Synthesis and Enzymatic Degradation of Nylon 66 Copolymers with Poly(Ethyleneglycol)s

Abstract

Nylon 66 (N66) copolymers were prepared by melt polycondensation of adipic acid and hexamethylenediamine with 5–80 mol% poly(ethylene glycol) (PEG), where the molecular weight (MW) of PEG was 200–1000. The reduced specific viscosity of the copolymers was increased by the copolymerization. The crystallinity and melting temperature (T _m) of N66 components decreased with increasing PEG content, but T _m depression of copolymers at the same mole content decreased with increasing MW of PEG, suggesting that the copolymer structures are not of the random type but of the block type at the higher MW of PEG. The water absorption increased with increasing PEG content, and its increase was much higher at the higher MW of PEG. The enzymatic degradation was estimated by the weight loss of copolymer films in the buffer solution with and without a lipase at 37°C. The weight loss was enhanced appreciably by the presence of a lipase, and increased abruptly at higher PEG content, which was correlated to water absorption and the concentration of ester linkages. The enzymatic degradation of these N66 copolymers was much higher than that of previously reported PET copolymers with PEG. The abrupt increase of weight loss by alkali hydrolysis was fairly comparable to that of water absorption.     

Thermo-Responsive Hydrogels Based on Branched Poly(L-lactide)-poly(ethylene glycol) Copolymers

Summary: Branched poly(L -lactide)-poly(ethylene glycol) (PLLA-PEG) block copolymers were synthesized from trifunctional PLLA and amine functionalized methoxy poly(ethylene glycol)s. The copolymers in water formed hydrogels that showed thermo-responsive behavior. The hydrogels underwent a gel to sol transition with increasing temperature as determined with the vial tilting method and oscillatory rheology. For all copolymers, the transition temperature increased with increasing copolymer concentration. The transition temperature of corresponding branched copolymers also increased with increasing PEG molecular weight, and surprisingly decreased with increasing molecular weight of the PLLA branches. In general, the gel-sol transition is explained by disruption of micellar or aggregate interactions because of partial dehydration and shrinkage of the PEG chains. An increase in the molecular weight of the PLLA branches led to the formation of micelles and aggregates as observed with DLS at low concentrations. It is speculated that the non-uniform size distribution and possible crystallization of longer PLLA blocks may have a negative effect on the formation of micellar packing upon gelation, allowing the disruption of micellar or aggregate interactions to occur at lower temperatures. The transition temperature of the gels could be tuned closely to body temperature by varying the concentration of the solution or the molecular weight of the PEG block and the PLLA blocks, which implies that these polymers may be used as injectable systems for in-situ gel formation.     

Investigation of swelling and network parameters of poly(ethylene glycol)-crosslinked poly(methyl vinyl ether-co-maleic acid) hydrogels

The influence of poly(ethylene glycol) (PEG) plasticiser content and molecular weight on the physicochemical properties of films cast from aqueous blends of poly(methyl vinyl ether-co-maleic acid) was investigated using thermal analysis, swelling studies, scanning electron microscopy (SEM) and attenuated total reflectance (ATR)-Fourier transform infrared (FTIR) spectroscopy. FTIR spectroscopy revealed a shift of the CO peak from 1708 to 1731 cm⁻¹, indicating that an esterification reaction had occurred upon heating, thus producing crosslinked films. Higher molecular weight PEGs (10,000 and 1000 Da, respectively), having greater chain length, producing hydrogel networks with lower crosslink densities and higher average molecular weight between two consecutive crosslinks. Accordingly, such materials exhibited higher swelling rates. Hydrogels crosslinked with a low molecular weight PEG (PEG 200) showed rigid networks with high crosslink densities and, therefore, lower swelling rates. Polymer:plasticizer ratio alteration did not yield any discernable patterns, regardless of the method of analysis. The polymer-water interaction parameter (χ) increased with increases in the crosslink density. SEM studies showed that porosity of the crosslinked films increased with increasing PEG MW, confirming what had been observed with swelling studies and thermal analysis, that the crosslink density must be decreased as the M_w of the crosslinker is increased. Hydrogels containing PMVE/MA/PEG 10,000 could be used for rapid delivery of drug, due to their low crosslink density. Moderately crosslinked PMVE/MA/PEG 1000 hydrogels or highly crosslinked PMVE/MA/PEG 200 systems could then be used in controlling the drug delivery rates. We are currently evaluating these systems, both alone and in combination, for use in sustained release drug delivery devices.     

Rheological behaviour of irradiated wound dressing poly(vinyl pyrrolidone) hydrogels

The use of hydrogels as biomaterials has increased lately. Poly(vinyl pyrrolidone) (PVP) is an example of polymer hydrogels applied for the synthesis of hydrogel to be used in different biomedical applications. This paper describes a study on rheological properties of PVP hydrogels obtained by gamma radiation techniques. PVP hydrogels were obtained by gamma radiation of PVP water solutions with different radiation doses. It was studied the influence of additives such as poly(ethylene glycol) (PEG), poly(ethylene oxide) (PEO) and glycerol on the rheological behaviour of the gel. The rheological behaviour of hydrogel samples was characterized by measuring the shear storage modulus (G′) under dynamic shear loading. Besides this, sterility and cytotoxicity tests were performed. The study on rheological behaviour of hydrogels showed that G′ of PVP gels change according to the additive used. Glycerol increases the fluidity of the gel. The influence of PEG depends on the amount and on its molecular mass. The increase on PEG amount and molecular mass cause a decrease of G′ and an increase in the crosslinking density of PVP hydrogel network. The use of high molecular weight PEO allows the increase of the elasticity of the PVP gels.     

Poly(N-isopropylacrylamide-co-N-t-butylacrylamide)-block-poly(ethylene glycol)-block-poly(N-isopropylacrylamide-co-N-t-butylacrylamide) triblock copolymers: synthesis and thermogelation properties of aqueous solutions

Novel triblock copolymers with PEG middle blocks of 1–10 kDa and poly(N-isopropylacrylamide-co-t-butylacrylamide) statistical copolymer side arms with DP_n?≈?88 and different compositions, were synthesized by SET-LRP. The thermogelation properties of their aqueous solutions depended on both hydrophobic monomer content of the side blocks and molecular weight (MW) of the poly(ethylene glycol) (PEG) middle block, as proven by dynamic rheometry, DSC, and tube inversion method measurements. At constant PEG chain length, increasing TBAM proportions led to a gelation process occurring at progressively lower temperatures, as well as to a lower stability of the forming hydrogels in the case of shorter-PEG-chain block copolymers. By employing longer PEG blocks (M_PEG ≥6,000 Da), stable hydrogels with the gelation temperature below 37 °C could be obtained. For a constant composition of the copolyacrylamide blocks, the dependence of the phase transition temperature (T_ph) on M_PEG displayed a different shape at different polymer solution concentrations, because of the stronger variation of T_ph with polymer concentration as M_PEG increased. Also, the viscoelastic properties of the hydrogels resulting from 20 wt.% polymer aqueous solutions at 37 °C were stronger affected by the MW of the PEG middle block than by the hydrophobic character of the thermosensitive side blocks.     

Effects of Poly(Ethylene Glycol) on the Physical Properties of Blended Molecules of Starch and Poly(Ethylene-co-Acrylate,Ammonium Salt)

Abstract

A mixture of starch (36%) poly(ethylene-co-acrylate, ammonium salt) (41%), water (12.5%), urea (8.4%), and poly(ethylene glycol) (M _n 4600) (2.1%) were converted to plastic test pieces by extruding (130°C), drying and grinding (25°C), and hot pressing (175°C). After equilibration at ?50% relative humidity and 25°C, the test pieces contained 3.5–4.6% moisture and 2.3% poly(ethylene glycol) (PEG). Among wheat, corn, potato, and rice starches, the wheat starch (WS) blend showed the highest Young's modulus (181.3 MPa), whereas the corn starch (CS) blend had a modulus and elongation that almost matched those of lowdensity polyethylene. When PEG was eliminated from the WS formulation, tensile strength remained constant, but Young's modulus doubled. The modulus decreased continually as test pieces absorbed water up to 27% moisture, but elongation and argon laser light transmittance were optimum at ?12% moisture. Differential scanning calorimetry indicated that PEG formed a solid inclusion complex with amylose upon drying at 60°C, but no complex was detected in dilute alkali by optical rotation.     

Preparation and characterization of macroporous poly(N‐isopropylacrylamide) hydrogels for the controlled release of proteins

Macroporous, temperature‐sensitive poly(N‐isopropylacrylamide) (PNIPAAm) hydrogels were synthesized with poly(ethylene glycol)s (PEGs; molecular weight = 2000–6000) as the pore‐forming agents. The influence of the molecular weight and PEG content on the responsive kinetics of these macroporous hydrogels was investigated. The PEG‐modified PNIPAAm hydrogels were characterized by the swelling ratio, deswelling–reswelling kinetics, Fourier transform infrared, and differential scanning calorimetry. The morphology of these hydrogels was analyzed with scanning electron microscopy. The prepared macroporous hydrogels exhibited some unique properties in comparison with the gels with low molecular weight PEGs (molecular weight < 2000) as the pore‐forming agents. In addition, a preliminary study on the controlled release of bovine serum albumin from these macroporous hydrogels was carried out. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 152–159, 2003     

Macroporous Poly(Acrylamide) Hydrogels: Swelling and Shrinking Behaviors

Macroporous poly(acrylamide) hydrogels have been synthesized by using poly(ethylene glycol) (PEG) with three different molecular weights as the pore‐forming agent. Scanning electron microscope graphs reveal that the macroporous network structure of the hydrogels can be adjusted by applying different molecular weights of PEG during the polymerization reaction. The swelling ratios of the PEG‐modified hydrogels were much higher than those for the same type of hydrogel prepared via conventional method. However, the swelling/deswelling ratios of the PEG‐modified hydrogels were affected slightly by the change in the amount of the PEG. Scanning electron microscopy experiments, together with swelling ratio studies, reveal that the PEG‐modified hydrogels are characterized by an open structure with more pores and higher swelling ratio, but lower mechanical strength, compared the conventional hydrogel. PAAm has potential applications in controlled release of macromolecular active agents.     

Swelling characterization of novel ternary semi‐IPNs: acrylamide/1‐vinylimidazole/PEG hydrogels

New ternary semi interpenetrating polymer networks (semi‐IPNs) systems containing acrylamide (AAm), 1‐vinylimidazole (VI) and poly (ethylene glycol) (PEG) have been prepared. AAm/VI hydrogels and semi‐IPN's, poly (AAm/VI/PEG) with 0.25, 0.50, 0.75 and 1.00 g of PEG (per 1.00 g AAm) were prepared by free radical solution polymerization in aqueous solution of AAm with VI as comonomer and a multifunctional crosslinker such as 1,4 butanediol dimethacrylate (BDMA). Swelling experiments were performed in water at 25°C, gravimetrically. The influence of VI and PEG content in hydrogels were examined. AAm/VI and AAm/VI/PEG hydrogels showed large extents of swelling in aqueous media, the swelling being highly dependent on the chemical composition of the hydrogels. Percentage swelling ratio of AAm/VI hydrogels and AAm/VI/PEG hydrogels was shown as 650–4167%. The values of equilibrium water content (EWC) of the hydrogels are between 0.8990 and 0.9750. Diffusion behavior was investigated. Water diffusion into hydrogels was found to be non‐Fickian in character. Copyright © 2007 John Wiley & Sons, Ltd.     

Morphology of Photopolymerized End-linked Poly(ethylene glycol) Hydrogels by Small Angle X-ray Scattering

Due to the biocompatibility of poly(ethylene glycol) (PEG), PEG-based hydrogels have attracted considerable interest for use as biomaterials in tissue engineering applications. In this work, we show that PEG-based hydrogels prepared by photopolymerization of PEG macromonomers functionalized with either acrylate or acrylamide end-groups generate networks with crosslink junctions of high functionality. Although the crosslink functionality is not well controlled, the resultant networks are sufficiently well ordered to generate a distinct correlation peak in the small angle x-ray scattering (SAXS) related to the distance between crosslink junctions within the PEG network. The crosslink spacing is a useful probe of the PEG chain conformation within the hydrogel and ranges from approximately 6 to 16 nm, dependent upon both the volume fraction of polymer and the molecular weight of the PEG macromonomers. The presence of a peak in the scattering of photopolymerized PEG networks is also correlated with an enhanced compressive modulus in comparison to PEG networks reported in the literature with much lower crosslink functionality that exhibit no scattering peak. This comparison demonstrates that the method used to link together PEG macromonomers has a critical impact on both the nanoscale structure and the macroscopic properties of the resultant hydrogel network.     

Supramolecular hydrogels induced rapidly by inclusion complexation of poly(epsilon-caprolactone)-poly(ethylene glycol)-poly(epsilon-caprolactone) block copolymers with alpha-cyclodextrin in aqueous solutions

On the basis of the synthesis of water-soluble poly(epsilon-caprolactone)-poly(ethylene glycol)-poly(epsilon-caprolactone) (PCL-PEG-PCL) block copolymers, the supramolecular hydrogels were fabricated rapidly in aqueous solutions by their inclusion complexation with alpha-cyclodextrin. X-ray diffraction (XRD) analyses confirmed the supramolecular self-assemblies of alpha-cyclodextrin threaded onto amphiphilic PCL-PEG-PCL block copolymers. The resulting hydrogels display a high degree of elasticity, with the storage modulus (G') greater than the loss modulus (G') over the entire range of frequency. Moreover, their viscosity greatly diminished as they were sheared. By controlling the molecular weight of the PEG component in the block copolymers and the content of the block copolymer, their rheological properties could be modulated. Such hydrogel materials have the potential to be used as tissue engineered scaffolds, biosensors in the human body, and carriers for controlled drug delivery.     

Biodegradable Polymers for Orthopedic Applications: Synthesis and Processability of Poly (l-Lactide) and Poly (Lactide-co-€-Caprolactone)

Abstract

The synthesis of poly(l-lactide) (PLLA), poly(l-lactide-co-e-caprolactone), and poly(DL-lactide-co-e-caprolactone) by ring-opening bulk polymerization was investigated. Polymerization temperature had a significant effect on the PLLA molecular weight. At 184°C a polymer with a molecular weight of only 10 × 10⁴ resulted. This was lower by a factor of 2 than that obtained at 103 and 145°C. The stannous octoate (SnOct) concentration, with a monomer/SnOct molar ratio in the range of 1,000 to 10,000, was not found to have a significant effect on the PLLA molecular weight. A heterogeneous structure in polymerized PLLA was observed. The intrinsic viscosity of poly(lactide-co-€-caprolactone), obtained at 130°C, monomer/SnOct molar ratio 5,000, and polymerization time of 30 hours, decreased with increasing €-caprolactone content within the first 9 wt% and then leveled off. Die-drawing of PLLA cylinders, for the purpose of increasing the polymer's mechanical strength, was unsuccessful due to the brittleness of the polymer. The drawability of poly(l-lactide), however, was greatly improved by copolymerization with €-caprolactone. With only 3 wt% of €-caprolactone, for example, the tensile strength of die-drawn poly(l-lactide-co-e-caprolactone) was increased by a factor of more than 3. Polymer processing temperature was also investigated. The requirement for low processing temperatures in melt manufacture of controlled release matrix devices containing thermal sensitive drugs was accomplished by three methods: through the use of low molecular weight poly(DL-lactide), adding (DL-lactic) acid oligomer to high molecular weight PDLLA, and copolymerizing DLLA with €-caprolactone. The glass transition temperatures of the modified high molecular weight PDLLA decreased significantly. Melt extrusion below 100°C could be performed.     

Aqueous Dispersion of Polyurethane Anionomer from Aliphatic Diisocyanates and Poly(Hexamethylene Carbonate) Diol

Abstract

Water dispersible polyurethanes (PUs) were prepared from poly(hexamethylene carbonate) (PHC) diol, isophorone diisocyanates (IPDI), hexamethylene diisocyanate (HDI), and dimethylolpropionic acid (DMPA) as latent anionic sites. After neutralization of the carboxyl group from the DMPA unit with triethylamine (TEA), the PU anionomers were dispersed by adding water, following by crosslinking using triethylenetetramine (TETA). The particle size of the dispersion decreased with the content of DMPA and increased with HDI in the HDI-IPDI system, and it exhibited a minimum when the number-average molecular weight (M _n) of the prepolymer was 3000 and 4500, respectively. PUs with a higher content of hard segments from DMPA or TETA, or with a higher content of IPDI rather than HDI, had higher tensile moduli and storage moduli at room temperature. Ultimate tensile properties increased with an increase of the prepolymer molecular weight and the DMPA and HDI content.     

PEG作为成孔剂对聚(N-异丙基丙烯酰胺-co-丙烯酸)水凝胶性能的影响

以PEG400,1000,6000为成孔剂,合成了一系列聚(N-异丙基丙烯酰胺co丙烯酸)水凝胶,研究了成孔剂分子量和数量对凝胶性能的影响.结果表明,聚乙二醇(PEG)分子充当成孔剂,不参与反应.PEG分子量越大,投料越多,所得凝胶孔的孔径越大,孔数目越多,在室温时可以容纳更多的水分子,因而溶胀率也越大.凝胶的大孔结构有利于水分子的进出,所以响应速率比普通共聚凝胶快.随着PEG分子量增大,孔数目增多,响应速率相应变快.     

Synthesis and swelling characterizations of a poly(gamma-glutamic acid) hydrogel

Natural, biosynthesized poly(gamma-glutamic acid) (γ-PGA) was crosslinked using dihalogenoalkanes yielding hydrogels with various features. Crosslinking reactions of the polymer and swelling of the hydrogels were studied. Various reaction parameters, like temperature and catalyst content, were adjusted to give highest yields in the network production. Swelling of the hydrogels showed dramatic changes when varying experimental conditions such as the molecular weight of γ-PGA, the nature and concentration of the crosslinker, and the solution used for the swelling (ionic strength, pH). © 1996 John Wiley & Sons, Inc.     

ENHANCED WATER SORPTION OF A SEMI-INTERPENETRATING POLYMER NETWORK (IPN) OF POLY(2-HYDROXYETHYL METHACRYLATE) (PHEMA) AND POLY(ETHYLENE GLYCOL) (PEG)

ABSTRACT

An attempt was made to enhance the water-sorption capacity of polymers of 2-hydroxyethyl methacrylate (HEMA) by preparing its semi-interpenetrating polymer network (IPN) with a hydrophilic polymer such as poly(ethylene glycol) (PEG). The effects of various factors, such as history of the polymer sample, chemical architecture of the IPN, presence of salt ions in the swelling medium, and temperature of the swelling medium, were investigated on the water sorption kinetics of the IPNs. The IPN was characterized by IR spectral analysis and various structural parameters, such as molecular weight between crosslinks (M_c), crosslink density (q) and number of elastically effective chains (V_e), were evaluated. The IPNs were also assessed for their antithrombogenic potential.     

A novel sodium carboxymethylcellulose/poly(N‐isopropylacrylamide)/Clay semi‐IPN nanocomposite hydrogel with improved response rate and mechanical properties

A novel semi‐IPN nanocomposite hydrogel (CMC/PNIPA/Clay hydrogel) based on linear sodium carboxymethylcellulose (CMC) and poly(N‐isopropylacrylamide) (PNIPA) crosslinked by inorganic clay was prepared. The structure and morphology of these hydrogels were investigated and their swelling and deswelling kinetics were studied in detail. TEM images showed that the clay was substantially exfoliated to form nano‐dimension platelets dispersed homogeneously in the hydrogels and acted as a multifunctional crosslinker. The CMC/PNIPA/Clay hydrogels swell faster than the corresponding PNIPA/Clay hydrogels at pH 7.4, whereas they swell slower than the PNIPA/Clay hydrogels at pH 1.2. The CMC/PNIPA/Clay nanocomposite hydrogels showed much higher deswelling rates, which was ascribed to more passway formed in these hydrogels for water to diffuse in and out. The deswelling process of the hydrogels could be approximately described by the first‐order kinetic equation and the deswelling rate decreased with increasing clay content. The mechanical properties of the CMC/PNIPA/Clay nanocomposite hydrogels were analyzed based on the theory of rubber elasticity. It was found that with increasing clay content, the effective crosslink chain density, v_e, increased whereas the molecular weight of the chains between crosslinks M_c decreased. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 1546–1555, 2008     

Effects of poly(ethylene glycol) (PEG) concentration on the permeability of PEG-grafted liposomes

Poly(ethylene glycol)-grafted liposomes (PEG-liposomes) were prepared from dipalmitoylphosphatidylcholine (DPPC) with various amounts of distearoyl-N-monomethoxy poly(ethylene glycol)-succinyl-phosphatidylethanolamines (DSPE-PEG) with PEG molecular weights of 1000, 2000, 3000 and 5000. The effects of DSPE-PEG concentration on the permeability of PEG-liposomes were investigated using carboxyfluorescein (CF). In the gel state, the CF leakage from PEG-liposomes was decreased with increasing mole fractions of DSPE-PEG for all PEG molecular weights. In the liquid-crystalline state, the CF leakage from PEG-liposomes containing DSPE-PEG1000 gradually increased with increasing mole fractions of DSPE-PEG, while that of PEG-liposomes whose molecular weight in PEG units was above 2000 rapidly decreased by the addition of DSPE-PEG. Furthermore, no effect of PEG molecular weight on CF leakage was observed. The relationship between the fluorescence polarization of 1,6-diphenyl-1,3,5-hexatriene (DPH) (or 1-(4-trimethylammoniumphenyl)-6-phenyl-1,3,5-hexatriene (TMA-DPH)) and the mole fraction of DSPE-PEG for PEG-liposomes was also investigated. No significant changes in fluorescence polarization of DPH for liposomal bilayer membranes was observed in the gel and liquid-crystalline states due to the addition of DSPE-PEG, while that of TMA-DPH was decreased compared with that of liposomes without DSPE-PEG in both states.     

Poly (caprolactone)/poly (ethylene glycol) pervaporation blend membranes: Synthesis,characterization, and performance

Poly (caprolactone) membranes with addition of different poly (ethylene glycol) concentrations were prepared for separation of water/isopropanol azeotropic mixture by pervaporation process. Different characterization tests including Fourier transform infrared, scanning electron microscopy, water contact angle, and thermogravimetric analysis were carried out on the prepared membranes. In addition, the effect of poly (ethylene glycol) PEG content on the swelling degree and the performance of the prepared membranes in pervaporation process were investigated. According to the obtained results, all the membranes were water selective and the blend membrane containing 3 wt% PEG exhibited the best pervaporation performance with a water flux of 0.517 kg/m² hour and separation factor of 1642 at the ambient temperature. Hydrophilicity improvement of the blend membranes was confirmed by constant decrease in water contact angle of the membranes as PEG content increased in the casting solution. Scanning electron microscopy cross‐sectional images indicated that the blend membranes containing PEG had a closed cellular structure. Furthermore, mechanical and thermal properties of the membranes decreased by adding PEG.     

Photo Polymerized Interpenetrating Polymer Network of Poly(antimony acrylate) and Poly(arsenic acrylate): Synthesis and Characterization

A series of IPN based on poly(antimony acrylate) and poly(arsenic acrylate) have been synthesized by a sequential mode of synthesis. Formation of complex based on “polymer solvent” method reflects the contraction of the polymer coils by determining the value of mutual interaction constant (k_AB) in different solvents such as dimethylsulphoxide (DMSO) (k_AB=0.60); dimethylformamide (DMF) (k_AB=0.42); dioxane (k_AB=0.26) predicting weak Vander Waal interaction. The scanning electron microscopy reveals dual phase morphology of both metal acrylates. The infrared spectrum indicates characteristic frequencies of (>C?O) at 1730 cm^?1,thus giving structural evidence for IPN. The properties namely percentage swelling, average molecular weight between crosslinks(M_c),Young's modulus, increases with concentrations of linear polymer(polyantimony acrylate) and initiator (benzoyl peroxide). However, it decreases with concentrations of monomer (arsenic acrylate) and crosslinker (divinyl benzene).The value of activation energy calculated from thermo gravimetric analysis is 15 KJ/mol.