Living Carbocationic Polymerization. XXIII. Analysis of Slow Initiation in Living Isobutylene Polymerization

The aim of this research was to develop a quantitative treatment of the consequences of relatively slow initiation on M _n and N (the number of molecules formed, W_p/M _n , where W_p =weight of polymer formed) in living carbocationic polymerizations, particularly for the case of the incremental monomer addition (IMA) technique. This has been achieved by analysis of the effect of initiator efficiency (I_eff (%) = 100N/[I ₀], where [I ₀] = initiator input) on M _n versus W_p , and N versus W_p plots. Three types of systems have been discerned: 1) I_eff equal to 100%; 2) I_eff constant but less than 100%; and 3) I_eff less than 100% but increasing with increasing number of monomer increments j by the IMA technique. Thus conditions can be found under which slowly initiating systems yield close to “ideal” product, i.e., one with M _n = [M₀ ]/[I₀ ] and narrow molecular weight distribution (M _w /M _n ≈ 1.1). The corresponding equations and plots can be used to diagnose the mechanism. Subsequently, this quantitative analysis was used to describe a novel living system, trans‐2,5‐diacetoxy‐2,5‐dimethyl‐3‐hexene (DiOAcDMH₆)/BCI₃/isobutylene/CH₃CI. This system produces linear t‐chlorine‐telechelic polyisobutylenes under homogeneous conditions. Surprisingly, cationation seems to be rate determining. This conclusion is illustrated by chemical equations.     

Quasiliving Carbocationic Polymerization. VII. Block Polymerization of α-Methylstyrene from Quasiliving Poly(isobutyl Vinyl Ether) Dication

Poly(α-methylstyrene-b-isobutyl vinyl ether-b-α-methylstyrene) triblock polymers have been prepared by blocking α-methyl-styrene (αMeSt) from biheaded quasiliving poly(isobuty1 vinyl ether) (PIBVE) cations generated with the bifunctional p-dicumyl chloride/AgSbF₆ initiating system in methylene chloride solvent at -90°C. The products were fractionated with 2-propanol, a good solvent for PIBVE and a nonsolvent for PaMeSt. The 2-propanol-insoluble fractions had much higher molecular weights (M _n = 30,500–69,100) than the starting PIBVE (M _n =6,600–10,600) and contained 13–29 wt% IBVE together with 87–71 wt% αMeSt units. The 2-propanol-soluble fractions (M _n = 7,300–11,600) contained ～90 wt% IBVE and ～10 wt% αMeSt units.     

Living Carbocationic Polymerization. XLIX. Two-Stage Living Polymerization of Isobutylene to Di-tert-chlorine Telechelic Polyisobutylene

Abstract

A two-stage process was developed for the living polymerization of isobutylene (IB) employing di-tert-alcohol initiators in conjunction with BCl₃ coinitiator in the first or initiation stage, followed by TiCl₄ coinitiator in the second or propagation stage; the process was shown to yield high molecular weight (up to M ⁿ 20,000), narrow molecular weight distribution (MWD) M ^w/M ⁿ = 1.1–1.2) di-tert-chlorine telechelic polyisobutylenes (^tCl-PIB-Cl^t). The initiation stage involves the homogeneous solution living polymerization of IB induced by the di-tert-alcohol/BCl₃ combination in the presence of an electron donor such as N,N-dimethylacetamide in CH₃Cl solvent at ?80°C and proceeds up to M ⁿ < 5000; this is followed by the propagation stage in which TiCl₄ and the bulk of IB plus a sufficient amount of n-C₆H₁₄ are added to the charge to bring the solvent composition to CH₃Cl/n-C₆H₁₄ 60/40 v/v and the living polymerization is continued until high M ⁿ product is obtained. This two-stage process was developed because 1) it employs very inexpensive chemicals; 2) di-tert-alcohol/BCl₃ combinations initiate living IB polymerization in CH₃Cl but the product after reaching M ⁿ ≤ 5000 precipitates out of the CH₃Cl solution, and di-tert-alcohol/BCl₄ combinations do not initiate IB polymerization; and 3) di-tert-alcohol/BCl₃ systems do not initiate (or only very slowly) the living polymerization of IB in CH₃Cl/n-C₆H₁₄ mixtures, whereas similar TiCl₄-based systems do. The polymerization remains living during both stages although the propagating species and solvent polarity are profoundly altered. The livingness of the system has been analyzed by kinetic experiments and the structure of the ^tCl-PIB-Cl^t product by routine spectroscopic means.     

Preliminary Study of Cationic Copolymerization of α-Methylstyrene and Isobutyl Vinyl Ether. II

α-Methylstyrene (α-MS) and isobutyl vinyl ether (IBVE) were copolymerized by using the H₂O/EtAlCl₂ initiator system and CH₂Cl₂ and CH₃Cl solvent in the temperature range from -30 to -90°C. As compared to homopolymerization of α-MS, both yields and molecular weights are reduced upon addition of small amounts of IBVE to the feed. The reactivity ratios were calculated by the method of Kelen and Tödös as well as the Fineman and Ross method, and the combined effect of change of solvent and temperature on reactivity ratios was determined. Effects of feed composition and temperature on the copolymer yield, composition, and number-average molecular weight M _n were studied in detail. M _n showed a novel exponential dependence on the IBVE concentration in the feed. The overall activation energies of molecular weight were determined from the Arrhenius plots for both homo-and copolymerization systems. Based on these and the yield data, a speculation is made regarding reaction mechanism for molecular weight control. NMR and DTA data are reported, which establish the random nature of the copolymers.     

New Interpretations: Molecular Weight Averages for a Polymer

The statement is often made in the polymer literature, without proof, that M _z ≤ M _w ≤ M _n, where M _z, M _w, and M _n are the z-, z weight-, and number-average molecular weights respectively. Four proofs of a generalization of these inequalities are given. It is shown that a higher-order molecular weight average is larger than a lower-order one, regardless of the form of the molecular weight distributions, except for the case when all the molecules have the same molecular weight. A brief discussion of the viscosity-average molecular weight is also included.     

Quasiliving Carbocationic Polymerization. VIII. Quasiliving Polymerization of Methyl Vinyl Ether and Its Blocking from Quasiliving Poly(isobutyl Vinyl Ether) Dication

Quasiliving carbocationic polymerization of methyl vinyl ether (MVE) was achieved with the p-dicumyl chloride (p-DCC)/AgSbF₆ initiator system by the slow and continuous monomer-addition (quasiliving) technique. A polar solvent (CH₂Cl₂) and a low reaction temperature (-70°C) were optimum for the quasiliving MVE polymerization. Under these conditions, the number-average molecular weight (M _n) of poly(MVE) increased linearly with the cumulative weight of added monomer (W_MVE), and linear M _n versus W_MVE plots passed through the origin. M _n's were inversely proportional to the initial initiator (p-DCC) concentration. Reactions in a nonpolar solvent (toluene) at -70°C or in a polar solvent (CH₂Cl₂) at ?30°C resulted in deviations from these quasiliving characteristics. Block polymerization of MVE from quasiliving poly(isobutyl vinyl ether) dications by the quasiliving technique (p-DCC/AgSbF₆ initiator, CH₂Cl₂ solvent,(-70°C) led to novel isobutyl vinyl ether (IBVE)-MVE block polymers in high yield (>93 wt%) and at high blocking efficiency. The block polymers, most likely poly(MVE-b-IBVE-b-MVE), having M _n = 10,900–14,000 [M _n(center block) = 6,200–9,0001, were soluble in n-heptane and insoluble in water, and gave hazy homogeneous solutions when dissolved in methanol at room temperature.     

Quasiliving Carbocationic Polymerization. II. The Discovery: The α-Methylstyrene System

A detailed analysis of elementary reactions of carbocationic polymerization culminated in the prediction and subsequent experimental demonstration of quasiliving polymerization. Quasiliving polymers are formed in a system provided that the process of chain termination and chain transfer to monomer are absent or reversible, i.e., the propagating ability of the chain end is maintained throughout the experiment, and the molecular weight increases in proportion to the cumulative amount of monomer added. The chain end can be active (carbocation) or dormant (reactivable polymeric olefin or cation source). Chain transfer is suppressed by keeping the monomer concentration low. Quasiliving polymerizations are maintained by continuous slow feeding of dilute monomer to a charge containing the initiating or propagating species (quasiliving polymerization technique). A comprehensive kinetic scheme has been developed that describes quasiliving polymerization in quantitative terms. Quasiliving polymerization was demonstrated experimentally in the “H₂O”/BCl₃/α-methylstyrene and cumyl chloride/BCl₃/α-methylstyrene systems. M _n versus monomer input plots are linear over wide ranges, indicating quasiliving conditions, and poly(α-methylstyrenes) with M _n > 2 × 10⁵ have been obtained, Molecular weight distributions were found progressively to narrow and dispersion ratios M _w/M _n to decrease.     

Crystallizable Polyphenylacetylene-Preparation and Solution Properties

The molecular weight distribution (MWD) of crystallizable polyphenylacetylene prepared near room temperature in the presence of ferric acetylacetonate and triethylaluminum was determined through use of fractions characterized by vapor pressure osmometry and gel permeation chromatography (GPC). The number- and weight-average molecular weights (M _n and M _w) are both less than the molecular weight corresponding to the maximum of the weight distribution function, which lacks a high molecular weight tail. M _wandM _n is less than is consistent with models allowing for chain termination characteristic of vinyl polymers. GPC elution volumes are much less than those characteristic of polystyrene of similar molecular weight, and the Mark-Houwink exponent is high (2.4 for M _v 4800 to 6800). These data indicate more rodlike behavior than for polystyrene of equivalent molecular weight. The MWD and other data suggest intramolecular chain termination, possibly associated with the molecule's tendency to form paramagnetic defect states.     

Ultrasonic Solution Degradations of Polystyrene and Substituted Polystyrenes in Tetrahydrofuran as Solvent

Abstract

Ultrasonic (70 W, 20 kHz) solution (2% THF) degradations of polystyrene (PS), poly(α-methylstyrene) (PαMeS), poly(p-isopropyl α-methylstyrene) (PpiPrαMeS), poly(p-chlorostyrene) (PpCIS), poly(p-bromostyrene) (PpBrS), and poly(p-methoxystyrene) (PpOMeS) have been carried out in tetrahydrofuran at 27° C. The average number of chain scissions S (where S = [(M _n)₀/(M _n)_t] - 1), computed from the overall values of [(M _n)₀ and (M _n)_t, were found to be different from those of S' (where S' = α([(M _n)₀/(M _n)_t] - 1)) based on the component (only that part of the polymer which is involved in degradation) data of the weight fraction (α), (M _n)₀, and (M _n)_t), S' for polystyrene and substituted polystyrene follows the order PS gt; PpCIS gt; PpiPrαMeS gt; PpBrS gt; PpOMeS gt; PαMeS. In the case of PS where degradations were also carried out at -20°C, lowering of the temperature increased the weight fraction of polymer degraded as well as S. Based on the viscosity and GPC data, it is concluded that the ultrasonic solution degradation of PS does not lead to branched polymers.     

Living Carbocationic Polymerization. Li. Living Carbocationic Copolymerization of Indene and p-Methylstyrene. 1. Demonstration of the Living and Random Copolymerization of Indene and p-Methylstyrene

Abstract

The living carbocationic polymerization and copolymerization of indene (Ind) and p-methylstyrene (pMeSt) have been investigated by the use of the 2-chloro-2,4,4-trimethylpentane (TMPCl)/TiCl₄ and the 2-chloro-2-propylbenzene (cumyl chloride, CumCl)/BCl₃ initiating systems in the presence of triethylamine (Et₃N) as electron donor and CH₃Cl or CH₃Cl/QH14 mixed solvents at ?80°C. The TMPCl/TiCl₄ initiating system gives essentially living copolymerization with slow initiation up to M _n ≈ 20,000. The CumCl/BCl₃ initiating system also induces living Ind homopolymerization up to at least M _n ≈ 13,000. The homopolymerization of pMeSt with the latter initiating system, however, is not living as it shows evidence for a large amount of chain transfer. Thus, with the CumCl/BCl₃ combination a small amount of chain transfer has apparently been observed in the presence of 50% of pMeSt in the charge. Reactivity ratio studies, fractionation, ¹H- and ¹³C-NMR spectroscopy, and glass transition temperature (T_g ) investigations indicate that virtually random Ind-co-pMeSt copolymers of M _n ≈ 20,000 can be obtained under suitable conditions. The T_g of the copolymers can be controlled between ≈115°C (the T_g of PpMeSt) and ≈194°C (the T_g of PInd) by the relative composition of the two monomers in the charge.     

Cationic copolymerization of indene with styrene derivatives: Synthesis of random copolymers of indene with high molecular weight

Random copolymers with high molecular weights of indene and p‐methylstyrene (pMeSt) were synthesized by cationic polymerization with trichloroacetic acid/tin tetrachloride in CH₂Cl₂ at low temperatures. When indene and pMeSt (1:1 v/v), for example, were polymerized at ?40 °C, both monomers were consumed at very similar rates to give a copolymer with high molecular weight [number‐average molecular weight (M_n): 8–9 × 10⁴]. This is indeed quite unexpected behavior for the combination of these two monomers because pMeSt polymerized over 1000 times faster than indene in the homopolymerization under the reaction conditions previously described. The product copolymer of indene and pMeSt had a random monomer sequence in it that was confirmed by NMR analyses and thermal‐property measurements. In sharp contrast with pMeSt, styrene and p‐chlorostyrene, which have no electron‐donating groups on the phenyl ring, led to low molecular weight polymers (M_n < 10,000) in the copolymerization with indene (1:1 v/v). © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 2449–2457, 2002     

Dilute Solution Properties of Poly(methacrylonitrile-co-styrene) and Poly(acrylonitrile-co-styrene)

Poly(methacrylonitrile-co-styrene) (PMANS) and Poly(acrylo-nitrile- co- styrene) (PANS) having 1:1 composition were prepared with free-radical initiators. The polymers were fractionated into fractions having narrow molecular weight distribution. The dilute solution properties of the fractionated copolymers were studied by light scattering, viscometry, and osmometry in solvents (methyl ethyl ketone, dimethylformamide, and acetone), [n]-M _w and(r²)_w ^l/2?M _w relationships have been established. The validity of the various graphical methods for the determination of Flory′s constant, K _θ were observed.

From the values of the steric factors it was noticed that the copolymer coil of PANS is stiffer than that of PMANS.     

Quasiliving Carbocationic Polymerization. IV. Polymerization of p-tert-Butylstyrene

The mechanism of polymerization of p-tert-butylstyrene (ptBuSt) initiated by the cumyl chloride/BCl₃ initiating system in CH₂Cl₂ at -50°C has been investigated. At and below ～0.4 M ptBuSt, quasiliving polymerizations proceed, i.e., initiation is instantaneous, termination is absent or reversible, and chain transfer to monomer can be suppressed or eliminated. In the quasiliving range the M _n versus [ptBuSt]₀ plot is linear and passes through the origin, and a M _w/M _n decreases much below 2.0 with decreasing [ptBuSt]. GPC traces change from broad multimodal to narrow monomodal and the color of polymerization charges change from colorless to golden-yellow with decreasing [ptBuSt]. The effect of temperature jump subsequent to monomer addition has been examined; however, it does not explain the peculiar monomer concentration effect on the mechanism. Changes in the ionicity may be responsible for this phenomenon.     

Characterization of Copolymers and Polymer Mixtures by Gel Permeation Chromatography

Abstract

Estimation of molecular weights from GPC data is complicated when the polymer sample consists of a mixture of homopolymers or of statistical copolymers with nonuniform compositions. This is because sizes of solvated polymer coils depend on solvent interaction with both the homo-and hetero-units of the copolymers and because the extent of solvation of different homopolymers can differ. The overall degree of solvation may change effectively with composition and use of a single “average” set of Mark-Houwink constants in calibration procedures will then produce false molecular weight data from the GPC data. A new molecular weight average, M _x, is defined to overcome this problem. This average can be determined from the GPC chromatogram and intrinsic viscosity of the sample in the GPC solvent. Mark-Houwink coefficients are not needed. M _x lies between M _w and M _z.     

Living Carbocationic Polymerization. LII. Living Carbocationic Copolymerization of Indene and p-Methylstyrene. 2. Synthesis,Characterization, and Physical Properties of Poly((Indene-co-p-Methylstyrene)-b-Isobutylene-b-(Indene-co-p-Methylstyrene)) Thermoplastic Elastomers

Abstract

Novel thermoplastic elastomers (TPEs) consisting of a central rubbery polyisobutylene (PIB) segment flanked by two glassy outer segments comprising indene (Ind)-co-p-methylstyrene (pMeSt) random copolymers have been prepared. The synthesis was effected by sequential monomer addition in one reactor: The process starts by the biliving homopolymerization of isobutylene (IB) and yields the living dication ⁺PIB⁺; the latter, upon the introduction of Ind/pMeSt mixtures, induces the living copolymerization of these monomers and yields the target TPE P(Ind-co-pMeSt)-b-PIB-b-P(Ind-co-pMeSt) triblock. The length of the rubbery midblock and the composition of the Ind-co-pMeSt random copolymer outer blocks (i.e., the overall composition of the triblocks) can be readily controlled. The glass transition temperature (T_g ) of the outer blocks can be fine-tuned by controlling the relative Ind/ pMeSt composition. The triblocks are excellent TPEs; for example, a P(Ind-co-pMeSt)-b-PIB-b-P(Ind-co-pMeSt) of M _n ≈ 115,000 g/mol containing a PIB midblock of M _n ≈ 70,200 g/mol and glassy copolymer outer blocks of P(Ind-co-pMeSt) [Ind/pMeSt = 41/59 (w/w)] exhibited 23.4 MPa tensile strength and 460% elongation. Tensile strengths and 300% moduli increase with the relative amount of the glassy segment present. Hardness increases with increasing Ind content.     

Quasiliving Carbocationic Polymerization. XIV. Synthesis of Poly(styrene-b-Isobutylene)

The synthesis of poly(styrene-b-isobutylenes) by the sequential addition of styrene and isobutylene has been accomplished. First a stream of styrene was added to a cumyl chloride/TiCl₄ in nhexane/methylene chloride charge at -50°C under quasiliving conditions. After the polystyrene block has reached a desirable sequence-length (molecular weight), gaseous isobutylene was continuously introduced to the quasiliving polystyrene carbocation until the polyisobutylene block also reached a desirable molecular weight. The M _n versus monomer input plot was uninterrupted and linear over both monomer introduction phases, indicating quasi-living conditions over the entire regime of block copolymer synthesis. The block copolymers have been characterized by selective solvent extraction and GPC, and their compositions determined by ¹H-NMR spectroscopy.     

Copolymers from Castor Oil Prepolymers (COP). 2. Copolymerization of Styrene with COP

A study of copolymerization of castor oil prepolymers (COP) with styrene has been made at 75°C using benzoyl peroxide as initiator. It has been found that good yields of copolymers (high molecular weight M _n = 123,989) are obtained at a low concentration of COP. With an increasing concentration of COP in the binary mixture, copolymers with decreasing molecular weight are obtained. This is explained as due to presence of a high percentage of oxygen (from COP) in the system which is acting as a chain transfer agent.     

Molecular dynamics in the nematic,SA and SC phases of 8S5 and 9S5 as studied by dielectric methods

Abstract

Two experimental techniques—time domain spectroscopy (TDS) and a steady state frequency method—have been used to study dielectric spectra for the isotropic, nematic, S_A, S_C and S_Y phases of two thioesters (4-n-pentylphenyl-4′-n-octyloxy-and 4′-n-nonyloxythiobenzoates (C _n H_2n+1 O?C₆ H₄?COS?C₆H₄?C₅H₁₁, where n = 8 and n = 9) known as 8S5 and 9S5, in the frequency range from 10 Hz to 10 GHz. In the case of 8S5 a deuteriated sample (8S5-d ₂₈) has been used to study relaxation processes in the nematic and smectic phases.     

Molecular Weight and Functionality Determination of Polyisobutylenes Containing Tertiary Chlorine Chain Ends by Thermal Dehydrochlorination

A sensitive thermal dehvdrochlorination method has been used to determine quantitatively the HCl arising from -CH₂C(CH₃)₂Cl endgroups in polyisobutylenes synthesized by BCb as the co-initiator. Quantitative endgroup analyses provided number-average molecular weights, M _n and functionality, F _n. Select M _n data obtained by this endgroup analysis is in agreement with those obtained by osmometry, GPC, and NMR techniques; indeed, M _n's obtained by this dehydrochlorination technique appears to be more accurate (2-3% error) than conventional methods (～5-10% error). The rate of HCl loss from -CH₂C(CH₃)₂Cl termini is first order in HCl with an ΔE_a of 19.1 kcal/mol in the 170-200°C range. This relatively low activation energy is most likely due to internal strain in the -CH₂C(CH₃)₂CH₂C(CH₃)₂Cl endgroup. These studies quantitatively substantiate earlier conclusions in regard to the mechanism of endgroup formation in BC13 coinitiated isobutylene polymerization.     

Copolymers of p-Nitrobenzyl Acrylate with Methyl Acrylate: Synthesis,Characterization, and Monomer Reactivity Ratios

Abstract

Copolymers of p-nitrobenzyl acrylate and methyl acrylate with different feed ratios are synthesized in ethyl methyl ketone using benzoyl peroxide as a free radical initiator at 70 ± 1°C. The copolymers were characterized by IR and ¹H-NMR spectroscopic techniques. Copolymer compositions were determined by ¹H-NMR analysis of the polymers. The monomer reactivity ratios were determined by the application of conventional linearization methods such as Fineman–Ross and Kelen–Tüdös. Gel permeation chromatography was used for determining the molecular weights M _n and M _w, and the polydispersity index. The intrinsic viscosities and the thermal properties of the homo- and copolymers are also discussed.