中空Ta_2O_5/TiO_2复合光催化剂的可控氧化制备及性能

以钛粉、钽粉为原料,炭黑作为反应性模板,通过熔盐法在炭黑表面原位生长了TaTiC_2纳米碳化物涂层,并以所得TaTiC_2/C复合物为碳化物前驱体,再经可控氧化制备出中空Ta_2O_5/TiO_2复合光催化剂。采用X射线粉末衍射(XRD)、扫描电子显微镜(SEM)、透射电子显微镜(TEM)、紫外-可见(UV-Vis)漫反射(DRS)及N2物理吸附等手段对所制备的光催化剂进行形貌、显微结构及孔结构表征。以高压汞灯为紫外光源,以亚甲基蓝为目标降解物,通过光催化降解实验评价中空Ta_2O_5/TiO_2复合光催化剂的光催化活性。结果表明,熔盐法生长碳化物涂层厚度均匀(20~30 nm),碳化物主要以TaTiC_2晶相存在且具有纳米级的颗粒尺寸。中空Ta_2O_5/TiO_2复合光催化剂同时具有200 nm左右的中空大孔结构及壳层10 nm左右的介孔结构。中空大孔和介孔的存在提高了所制备催化剂对亚甲基蓝的吸附能力。此外,TiO_2与Ta2O5通过电子能带结构的耦合,有效提高了光生电子和空穴的分离效率,从而显著提高了光催化活性。nTi∶nTa=2.5∶1.5时,相应的中空Ta_2O_5/TiO_2复合光催化剂表现出最佳的光催化活性,对亚甲基蓝的紫外光催化降解率高达97%。     

中空Ta2O5/TiO2复合光催化剂的可控氧化制备及性能

以钛粉、钽粉为原料,炭黑作为反应性模板,通过熔盐法在炭黑表面原位生长了TaTiC₂纳米碳化物涂层,并以所得TaTiC₂/C复合物为碳化物前驱体,再经可控氧化制备出中空Ta₂O₅/TiO₂复合光催化剂。采用X射线粉末衍射（XRD）、扫描电子显微镜（SEM）、透射电子显微镜（TEM）、紫外-可见（UV-Vis）漫反射（DRS）及N₂物理吸附等手段对所制备的光催化剂进行形貌、显微结构及孔结构表征。以高压汞灯为紫外光源,以亚甲基蓝为目标降解物,通过光催化降解实验评价中空Ta₂O₅/TiO₂复合光催化剂的光催化活性。结果表明,熔盐法生长碳化物涂层厚度均匀（20~30 nm）,碳化物主要以TaTiC₂晶相存在且具有纳米级的颗粒尺寸。中空Ta₂O₅/TiO₂复合光催化剂同时具有200 nm左右的中空大孔结构及壳层10 nm左右的介孔结构。中空大孔和介孔的存在提高了所制备催化剂对亚甲基蓝的吸附能力。此外,TiO₂与Ta₂O₅通过电子能带结构的耦合,有效提高了光生电子和空穴的分离效率,从而显著提高了光催化活性。n_Ti∶n_Ta=2.5∶1.5时,相应的中空Ta₂O₅/TiO₂复合光催化剂表现出最佳的光催化活性,对亚甲基蓝的紫外光催化降解率高达97%。     

Adsorption properties and photocatalytic activity of TiO2 and La-doped TiO2

Photocatalysts of TiO₂ and La-doped TiO₂ were prepared by calcining the pure TiO₂ sols and the sols mixed with La(NO₃)₃⋅6H₂O at 873 K, respectively. These photocatalysts were characterized by X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM) and N₂ adsorption-desorption isotherms measurement. As results, the BET surface area, pore diameter, mesopore volume and micropore volume slightly increased, while the crystallite size and the phase structure were little affected by lanthanum doping. The equilibrium adsorption of methylene blue (MB) on the photocatalysts were measured in a dark room. The adsorption isotherms were confirmed to fit to the Langmuir theory. Photocatalytic activities of the photocatalysts were studied by employing the photocatalytic degradation of MB in water and degradation of acetaldehyde in air under UV-irradiation using a black light. Kinetic analysis revealed that the rate controlling steps could be the surface reaction of the adsorbed MB on the catalyst surface for MB degradation and the reaction of adsorbed acetaldehyde with the gaseous acetaldehyde for degradation of acetaldehyde, respectively.     

Photocatalytic activities of poly(methyl methacrylate)/titanium dioxide nanofiber mat

This study aimed to evaluate the photocatalytic activities of poly(methyl methacrylate) (PMMA)/titanium dioxide (TiO₂) nanofiber mat. TiO₂ nanoparticles in crystal phase were first prepared by sol-gel process and then PMMA/TiO₂ nanofiber mat was prepared through electrospinning. The composite (PMMA/TiO₂) nanofiber mat was compared with that of pure PMMA nanofiber mat through performing FTIR and UV-Vis spectroscopy, scanning electron microscopy, thermogravimetric analysis, weight loss and water contact angle measurements. The photocatalytic activity of PMMA/TiO₂ nanofiber mat was evaluated by investigating both the photocatalytic decomposition of a model dye, methylene blue, and photocatalytic degradation of the composite nanofiber mat in the ambient air under ultraviolet light irradiation.     

Effect of Cl− anions on photocatalytic decomposition of gaseous ozone over Au @ Ag/TiO2 catalyst

Au core Ag shell composite structure nanoparticles were prepared using a sol method. The Au core Ag shell composite nanoparticles were loaded on TiO₂ nanoparticles as support using a modified powder–sol method, enabling the generation of Au @ Ag/TiO₂ photocatalysts for photocatalytic decomposition and elimination of ozone. The sols were characterized by means of ultraviolet–visible light (UV–Vis) reflection spectrometry, X-ray photoelectron spectroscopy (XPS), and transmission electron microscopy (TEM). The activity of the Au @ Ag/TiO₂ photocatalysts for photocatalytic decomposition and elimination of ozone was evaluated and the effect of Cl^? anions on the photocatalytic activity of the catalysts was highlighted. Results showed that Au @ Ag/TiO₂ prepared via the modified powder–sol route in the presence of an appropriate amount of NaCl solid as demulsifier had better activity in the photocatalytic decomposition and elimination of ozone. At the same time, Au @ Ag/TiO₂ catalysts had better ability to resist poisonous Cl^? anions than conventional Au/TiO₂ catalyst. The reasons could be, first, that NaCl was capable of reducing the concentration of free Ag⁺ by adsorption on the surface of Ag particles forming AgCl and enhancing the formation of Au core Ag shell particles, leading to a better resistance to Cl^? anions of the catalysts, and, second, AgCl took part in the photocatalytic decomposition of ozone together with Au @ Ag/TiO₂ catalysts and had a synergistic effect on the latter, resulting in better photocatalytic activity of Au @ Ag/TiO₂ catalysts.     

Surface morphology and active sites of TiO<Subscript>2</Subscript> for photoassisted catalysis

The main aim of this work is to discriminate the closely related adsorption and catalytic degradation processes that occur during a photocatalytic reaction. Very high-surface-area TiO₂ and Pd-doped TiO₂ were synthesized by microwave-assisted hydrothermal synthesis and used for degradation of methylene blue as a model pollutant dye. Thorough structural, morphological, and surface analyses of the synthesized catalysts were conducted to investigate key material properties that influence adsorption and catalytic performance. The adsorption capacity of the catalysts was determined by fitting adsorption data using the Langmuir isotherm model, and the photocatalytic activity of the synthesized samples was evaluated by periodically measuring the concentration of methylene blue as it was photocatalytically degraded under ultraviolet (UV) light. The results indicated that noble-metal incorporation compromised adsorption but favored catalytic performance.     

生物质C-N-P自掺杂TiO_2的合成及其对亚甲基兰的光催化降解活性

采用溶胶-超声辐照技术同步合成了生物质C-N-P自掺杂TiO_2复合催化剂,通过X射线光电子能谱(XPS)、X射线衍射(XRD)、扫描电子显微镜(FESEM)、紫外-可见漫反射光谱(UV-Vis-DRS)及光致发光光谱(PL)对样品进行了表征.以亚甲基兰(MB)为目标污染物,研究了C-N-P共掺杂TiO_2的可见光光催化性能.实验结果表明,在可见光照射下,光催化反应时间为2 h时,C-N-P共掺杂TiO_2复合催化剂对亚甲基兰的降解效率最高可达9 8.5%;相比纯TiO_2,C-N-P共掺杂TiO_2复合催化剂的比表面积增大,吸收边带红移,禁带宽度减小,相变温度升高,光生载流子复合率降低.     

Gamma irradiation induced preparation of poly(acrylamide–itaconic acid)/zirconium hydrous oxide for removal of Cs-134 radionuclide and methylene blue

Adsorption experiments were carried out to investigate the removal of Cs-134 radionuclide and methylene blue (MB) from aqueous solution using poly(acrylamide–itaconic acid)/N,N′-methelyenediacrylamide/zirconium hydrous oxide composite [poly(AM–IA)/DAM/Zr(OH)₄] as an adsorbent. The effects of initial pH value, initial concentration of Cs or MB, adsorbent dose, contact time and temperature on adsorption were investigated. Characterization of the prepared composite was carried out using FT-IR, XRD, TGA, DTA, and SEM. The adsorption behaviors showed that the adsorption kinetics and isotherms were in good agreement with the pseudo-second-order and the Langmuir models indicating the chemosorption mechanism. Thermodynamic studies were carried out and it was found that the process was spontaneous exothermic in nature. Discussion of the results of the adsorption behavior showed that the prepared composite can be used as a promising adsorbent for removal of Cs-134 or MB.     

The photocatalytic properties of Ti–Mo oxides prepared by a simple sol–gel route

Powders containing mixtures of titania and molybdite in different ratios were prepared by sol–gel processing. The sols were dried and subsequently calcined at 300, 500 and 700 °C. Depending on the ratio of Ti and Mo in the initial sol and the calcination temperature, Ti-doped MoO₃, TiO₂/MoO₃ or Mo-doped TiO₂ have been formed. The as prepared samples were characterised by scanning electron microscopy with attached X-ray dispersive energy analysis, X-ray diffractometry, Raman spectroscopy, gas adsorption and optical characterisation by ultraviolet/visible spectroscopy. The latter was used for the analysis of the photocatalytic properties on the decolourisation of methylene blue solutions under visible light irradiation. The phase composition, the specific surface and the photocatalytic activity were influenced by the molybdenum content and the calcination temperature. The final molybdenum content in the samples additionally depends on the calcination temperature. The optimum photocatalytic properties were observed or Ti-doped MoO₃.     

非共价修饰碳纳米管/二氧化钛复合材料的合成及性能

采用溶胶-凝胶法在聚乙烯吡咯烷酮(PVP)非共价修饰的碳纳米管表面均匀沉积二氧化钛粒子制得纳米复合材料。用TEM、XRD、FTIR、N2吸脱附等对复合材料进行了表征。结果表明:纳米二氧化钛纳米粒子均匀沉积在被修饰碳纳米管表面,且二氧化钛为纯锐钛矿晶体结构,没有金红石和板钛矿相。非共价修饰碳纳米管/二氧化钛复合材料具有良好的介孔结构,其孔径分布主要集中在6～10 nm,且比表面积与纯的二氧化钛相比明显增大,在紫外光照射下降解亚甲基蓝,相比纯的二氧化钛和碳纳米管/二氧化钛,具有较高的催化活性。     

Photocatalytic activity of polyaniline/Fe-doped TiO2 composites by in situ polymerization method

This study was focused on the photocatalytic activity of polyaniline (Pani)/iron doped titanium dioxide (Fe–TiO₂) composites for the degradation of methylene blue as a model dye. TiO₂ nanoparticles were doped with iron ions (Fe) using the wet impregnation method and the doped nanoparticles were further combined with Pani via an in situ polymerization method. For comparison purposes, Pani composites were also synthesized in the presence undoped TiO₂. The photocatalyst and the composites were characterized by standard analytical techniques such as FTIR, XRD, SEM, EDX and UV–Vis spectroscopies. Fe–TiO₂ and its composites exhibited enhanced photocatalytic activity under ultraviolet light irradiation. Improved photocatalytic activity of Fe–TiO₂ was attributed to the dopant Fe ions hindering the recombination of the photoinduced charge carriers. Pani/Fe–TiO₂ composite with 30?wt.% of TiO₂ nanoparticles achieved 28% dye removal and the discoloration rate of methylene blue for the sample was 0.0025?min^?1. FTIR, XRD, SEM, EDX and UV–Vis spectroscopies supported the idea that Fe ions integrated into TiO₂ crystal structure and Pani composites were successfully synthesized in the presence of the photocatalyst nanoparticles. The novelty of this study was to investigate the photocatalytic activity of Pani composites, containing iron doped TiO₂ and to compare their results with that of Pani/TiO₂.     

可见光下具有高光子效应和光催化活性的CuS-石墨烯氧化物/TiO2复合材料的制备（英文）

CuS-graphene oxide/TiO2 composites were prepared using a sol-gel method to improve the photocatalytic performance of the photocatalyst. The composites were characterized by X-ray diffraction, scanning electron microscopy, energy-dispersive X-ray analysis, and transmission electron microscopy. The photocatalytic activities were examined by the degradation of methylene blue (MB) under visible-light irradiation. The photodegradation of MB under visible-light irradiation reached 90.1% after 120 min. The kinetics of MB degradation was plotted alongside the values calculated from the Langmuir-Hinshelwood equation. The CuS-graphene oxide/TiO2 sample prepared using 0.2 mol of TiO2 showed the best photocatalytic activity. This was attributed to a cooperative reaction as a result of increased photoabsorption by graphene oxide and an increased photocatalytic effect by CuS.     

Characterization of TiO2 Loaded on Activated Carbon Fibers and Its Photocatalytic Reactivity

In this paper, TiO2 loaded on activated carbon fibers （ACF） was prepared by a coating treatment, followed by calcination at different temperatures in air atmosphere. The photocatalyst developed was characterized by SEM, XRD, XPS and UV-Vis adsorption spectroscopy. It was observed from SEM images that TiO2 loaded on ACF was in the form of small clusters with nanometer size. As confirmed by XRD and XPS determinations, the crystalline pattern of immobilized TiO2 was still anatase-form after calcination, and the micrographic structure and surface properties of ACF have not been damaged by the deposition process and calcination at different temperatures. Photocatalytic degradation of methylene blue （MB） in aqueous .solution was investigated using TiOE/ACF as photocatalyst. The comparison of photolysis, absorption and photocatalysis was carded out. The results indicated that the photocatalysis process of combined photocatalyst showed much higher degradation rate than that of photolysis and absorption processes. In addition, the possibility of cyclic usage of the photocatalyst was also confirmed.     

Sol–gel preparation of pure and doped TiO2 films for the photocatalytic oxidation of ethanol in air

Stable sols of TiO₂ were synthesized by a non-aqueous sol–gel process using titanium (IV) isopropoxide as precursor. The microstructure, optical and morphological properties of the films obtained by spin-coating from the sol, and annealed at different temperatures, were investigated using scanning electron microscopy, transmission electron microscopy, diffuse reflectance spectroscopy and ellipsometry. The crystalline structure of the films was characterized by X-ray diffraction and their photocatalytic activity was evaluated for the oxidation of ethanol in air. The influence of the calcination temperature, pre-heat treatment and the number of layers was studied. Simultaneous thermo-gravimetric and differential thermal analysis measurements were carried out to ascertain the thermal decomposition behavior of the precursors. In order to obtain a higher photoresponse in the visible region, a series of vanadium-, niobium- and tantalum-doped TiO₂ catalysts was synthesized by the same sol–gel method. For V doping two different precursors, a vanadium alkoxide and V₂O₅, were used. The effect on the crystallization and photocatalytic activity of the doped TiO₂ films was investigated. Furthermore, to identify the effective composition of the samples, they were characterized by X-ray photoelectron spectroscopy and the surface area of the powders was measured by N₂ adsorption. The 10 wt.% doped catalysts exhibit high photocatalytic activity under visible light and among them the best performance was obtained for the sample containing Ta as dopant. The crystallite sizes are closely related to the photocatalytic activity.     

Synthesis of TiO2/Bi2WO6 nanofibers with electrospinning technique for photocatalytic methyl blue degradation

TiO₂/Bi₂WO₆ composite nanofibers have been successfully synthesized by a simple electrospinning process. XRD, SEM, HR-TEM, nitrogen adsorption–desorption isotherms and UV–visible diffuse reflectance spectra were used to characterize the composite nanofibers. The composite fibers with diameters about 100 nm was composed of nanoparticles and possessed of high specific surface area (49.6 m² g^?1) and porous structure. Besides, the TiO₂/Bi₂WO₆ composite nanofibers exhibited excellent visible photocatalytic property in the photodegradation of methylene blue (MB), and over 97.2 % of MB was degraded within 5.5 h.     

Microstructure of SiO<Subscript>2</Subscript>/TiO<Subscript>2</Subscript> hybrid electrospun nanofibers and their application in dye degradation

SiO₂/TiO₂ hybrid nanofibers were prepared by electrospinning and applied for photocatalytic degradation of methylene blue (MB). The phase structure, specific surface area, and surface morphologies of the SiO₂/TiO₂ hybrid nanofibers were characterized through thermogravimetry (TG), X-ray diffraction (XRD) analysis, Brunauer–Emmett–Teller (BET) analysis, scanning electron microscopy (SEM), etc. XRD measurements indicated that doping of silica into TiO₂ nanofibers can delay the phase transition from anatase to rutile and decrease the grain size. SEM and BET characterization proved that silica doping can remarkably enhance the porosity of the SiO₂/TiO₂ hybrid nanofibers. The MB adsorption capacity and photocatalytic activity of the SiO₂/TiO₂ hybrid nanofibers were distinguished experimentally. It was found that, although increased silica doping content could enhance the MB adsorption capacity, the intrinsic photocatalytic activity gradually dropped. The SiO₂ (10 %)/TiO₂ composite nanofibers exhibited the highest MB degradation rate, being superior to SiO₂ (20 %)/TiO₂ or pure TiO₂.     

Synthesis,characterization and photocatalytic properties of tungsten-doped hydrothermal TiO<Subscript>2</Subscript>

Crystalline anatase phase TiO₂ with photocatalytic properties was obtained through a sol–gel low-temperature hydrothermal process. TiO₂ samples doped with tungsten oxide were also obtained by using this synthetic approach. The photocatalytic oxidation of methylene blue in water was monitored to study the influence of the tungsten doping degree on the photocatalytic degradation performance of TiO₂. The degradation rate constant was further increased by adjusting the tungsten doping degree of hydrothermal TiO₂. Also, a much faster photodegradation of methylene blue was achieved using tungsten doped samples baked at 450°C. The results were compared with those obtained with Degussa P25 used as photocatalyst. The structure and optical properties of tungsten-doped TiO₂ were studied by SEM, X-ray diffraction, UV–vis and DRIFT spectroscopy techniques.     

Template‐free Fabrication of ZnS/TiO2 Photocatalyst with Macrochannels

Constructing a porous structure in photocatalysts is an effective strategy for improving the photocatalytic activity because of its enhanced molecule transfer capability and light capturing efficiency. In this work, a hierarchical macro‐/mesoporous ZnS/TiO₂ composite with macrochannels was successfully synthesized without using templates by the simple dropwise addition of an ethanol solution of tetrabutyl titanate and zinc acetate into a sodium sulfide aqueous solution, which was then calcined at 450°C. Compared with pure TiO₂, the ordered porous ZnS/TiO₂ composite exhibited an enhanced photocatalytic activity on methylene blue removal under UV‐light irradiation. The results indicate that the macro‐/mesoporous structure, the large specific surface area, and the heterostructure combination between ZnS and TiO₂ play a synergistic effect on the enhanced photocatalytic activity via improving the light absorption and the diffusion of organic molecules, providing more reactive sites for the photocatalytic reaction and improving the separation of photogenerated electron–hole pairs, respectively. Radical trapping experiments demonstrated that holes (h⁺) and superoxide anion radicals (O₂⁻) play an important role in the photocatalytic oxidation process.     

F and Fe co-doped TiO2 with enhanced visible light photocatalytic activity

Four different sols, pure TiO₂, F doped TiO₂, Fe doped TiO₂, and F–Fe co-doped TiO₂ sols, were prepared by peroxidation at low temperature. The crystal structure, morphology, light adsorption, and photocatalytic properties of the pure and doped TiO₂ were examined by X-ray diffraction, transmission electron microscopy, and ultraviolet–visible spectrophotometry. The relationship between the average size, crystal type, range of visible light absorption, and photocatalytic activity and content and type of doped ions were investigated. The results showed that the average size of the F–Fe co-doped TiO₂ composed of both the anatase and rutile phases was the same as that of pure TiO₂. Furthermore, the visible light photocatalytic activity of the F–Fe co-doped TiO₂ was significantly improved over pure TiO₂, F-doped TiO₂, and Fe-doped TiO₂ due to the large red shift in the light adsorption edge.     

Mesoporous titania photocatalyst: effect of relative humidity and aging on the preparation of mesoporous titania and on its photocatalytic activity performance

Mesoporous TiO₂ has been synthesized by the sol–gel method, using a nonionic triblock copolymer P123 as surfactant template under acidic conditions. The as-prepared samples were characterized by thermogravimetry–differential thermal analysis (TG–DTA), nitrogen absorption–desorption (BET), field emission scanning electron microscopy, and transmission electron microscopy. The photocatalytic activity of the mesoporous TiO₂ was evaluated by degradation of methylene blue under high-intensity UV light irradiation; the amount of methylene blue was measured by UV–visible spectroscopy. TG–DTA analysis revealed that the surfactant had been removed partly in as-synthesized samples. BET analysis proved that all the samples retained mesoporosity with a narrow pore-size distribution (4.5–6.3 nm) and high surface area (103–200 m²/g). All calcined mesoporous TiO₂ had high photocatalytic activity in the photodegradation of methylene blue.