Molecular Design of TPD-based Organic A-π-D-π-A Dyes for Dye-sensitized Solar Cells

An interesitng class of organic A-π-D-π-A dyes based on an N,N,N′,N′-tetraphenylbenzidine(TPD) unit as donor was designed and synthesized for dye-sensitized solar cells(DSSCs). TPD-4-based DSSCs gave a short circuit photocurrent density(J_sc) of 16.67 mA/cm², a open circuit voltage(V_oc) of 0.635 V and a fill factor(ff) of 0.68, achieving a solar-to-electricity conversion efficiency(η) of 7.22% in preliminary tests. The N3-sensitized device gave an η value of 8.02% with a J_sc of 18.81 mA/cm², a V_oc of 0.630 V and an ff of 0.68 under the same conditions. The incident photo-to-current efficiency(IPCE) values above 70% observed in a range of 460 to 600 nm with a maximum value of 80% at 500 nm indicate that the TPD-4-based DSSC shows a high performance. Under the same conditions, the DSSC based on N3 provided the IPCE values above 70% in a range of 490 to 580 nm with a maximum value of 76% at 500 nm. Both further optimization of the device processing and structural modification of these dyes are anticipated to make the device give even better performances.     

Effect of organic dye on the performance of dye-sensitized solar cell utilizing TiO2 nanostructure films synthesized via CTAB-assisted liquid phase deposition technique

This work is concerned with the growth of TiO₂ nanostructures as photovoltaic materials of dyesensitized solar cell (DSSC) via phase liquid deposition technique treated with CTAB surfactant. This work investigates the influence of organic dyes, N719, N3 and Z907 as photosensitizer on the photovoltaic parameters of TiO₂ nanostructures dye-sensitized solar cells (DSSCs). It also highlights the effect of the concentration of the best dye, N719 on the performance of the cell. The platinum films as counter electrode of the DSSC were prepared by sputtering platinum pellet on ITO substrate. The redox couple of the electrolyte utilized in the DSSC was iodide/triiodide. The cell sensitized with N719 dye demonstrated the best performance compared with the cell sensitized with another two dyes, N3 and Z907. This is due to N719 dye possess the highest optical absorption in visible region. The cell sensitized with 0.8 mM N719 dye performs the highest short-circuit current density, J _sc and power conversion efficiency, η since it posses the highest absorption in visible region. The DSSC utilizing 0.8 mM N719 dye demonstrated the highest J _sc and η of 6.48 mA cm^?2 and 1.69%, respectively.     

Dipolar Compounds Containing Fluorene and a Heteroaromatic Ring as the Conjugating Bridge for High‐Performance Dye‐Sensitized Solar Cells

A novel series of dipolar organic dyes containing diarylamine as the electron donor, 2‐cyanoacrylic acid as the electron acceptor, and fluorene and a heteroaromatic ring as the conjugating bridge have been developed and characterized. These metal‐free dyes exhibited very high molar extinction coefficients in the electronic absorption spectra and have been successfully fabricated as efficient nanocrystalline TiO₂ dye‐sensitized solar cells (DSSCs). The solar‐energy‐to‐electricity conversion efficiencies of DSSCs ranged from 4.92 to 6.88 %, which reached 68–96 % of a standard device of N719 fabricated and measured under the same conditions. With a TiO₂ film thickness of 6 μm, DSSCs based on these dyes had photocurrents surpassing that of the N719‐based device. DFT computation results on these dyes also provide detailed structural information in connection with their high cell performance.     

Ethoxy‐substituted Oligo‐phenylenevinylene‐Bridged Organic Dyes for Efficient Dye‐Sensitized Solar Cells

Organic dyes with ethoxy‐substituted oligo‐phenylenevinylene as chromophores were synthesized for dye‐sensitized solar cells (DSSCs), and the detailed relationships between the dye structures, photophysical properties, electrochemical properties, and performances of DSSCs were described. The dye S3O showed broad IPCE spectra in the spectral range of 350–750 nm, and the dye S1P showed solar energy‐to‐electricity conversion efficiency (() of up to 4.23% under AM 1.5 irradiation (100 mW/cm²) in comparison with the reference Ru‐complex (N719 dye) with an η value of 5.90% under similar experimental conditions.     

应用于染料敏化太阳能电池的基于染料R6的含有不同吸电子基团的有机染料的理论研究

Dye-sensitized solar cells (DSSCs) are the most promising alternatives to traditional fossil energy because of their advantages of low production cost, facile structure, relatively low environmental impact, relatively high photoelectronic absorption efficiency, and overall high efficiency. In addition, several studies on sensitizers as vital components have been conducted over the last three decades. Compared to metal dyes, metal-free organic dyes have been considered as promising candidates because of their simple fabrication, multiple structures, high molar absorption coefficients, easily tunable properties, and environmental friendliness. In this study, we systematically investigated the optoelectronic properties of six metal-free organic donor-acceptor dyes (RD1–6) derived from the known dye R6 by using the density functional theory (DFT) and time-dependent DFT methods. Cell performance parameters were discussed, including the geometrical and electronic structures, absorption spectrum, adsorption energy, light harvesting efficiency (LHE) curve, predictive short circuit current density (J_sc^Pred.), predictive open circuit voltage (V_oc^Pred.), and theoretical power conversion efficiency (PCE). Results revealed that all the designed dyes exhibited high theoretical PCE. In particular, dyes RD1, 2, and 4–6 showed greater conjugations, and dyes RD1–3 had smaller energy gaps than those of the reference dye. In addition, dyes RD1–3, 5, and 6 exhibited better light harvesting capacities that covered the entire visible region and extended to the near-infrared region with obviously red-shift maximum absorption wavelengths (λ_max), wider LHE curves, and higher J_sc^Pred. as compared to the reference dye. It was critical that dyes RD1 and 2 not only have greater conjugations and narrow band gaps but also good light harvesting capacities with more than 56-nm red-shift maximum absorption wavelengths and broadened LHE curves than those of the reference dye. Notably, mainly because of an average increment of 12.0% of J_sc^Pred., a remarkable increment of the theoretical power conversion efficiency was observed from 12.6% for dye R6 to 14.1% for dyes RD1 and 2. Thus, dyes RD1 and 2 exhibited superior cell performances and could be promising sensitizer candidates for highly efficient DSSCs. These results could be used to guide effective synthetic efforts in the discovery of efficient metal-free organic dye sensitizers in DSSCs.     

Surface-treated TiO2 nanoparticles for dye-sensitized solar cells with remarkably enhanced performance

Dye-sensitized solar cells (DSSCs) were prepared by capitalizing on mesoporous P-25 TiO(2) nanoparticle film sensitized with N719 dyes. Subjecting TiO(2) nanoparticle films to TiCl(4) treatment, the device performance was improved. More importantly, O(2) plasma processing of TiO(2) film that was not previously TiCl(4)-treated resulted in a lower efficiency; by contrast, subsequent O(2) plasma exposure after TiCl(4) treatment markedly enhanced the power conversion efficiency, PCE, of DSSCs. Remarkably, with TiCl(4) and O(2) plasma treatments dye-sensitized TiO(2) nanoparticle solar cells produced with 21 μm thick TiO(2) film illuminated under 100 mW/cm(2) exhibited a PCE as high as 8.35%, twice of untreated cells of 3.86%.     

基于咔唑染料敏化剂的合成及电喷雾的DSSC器件制备

本文设计并合成了两个不含金属的新型纯有机染料CBR和CI,用核磁共振、MALDI-TOF、紫外可见吸收光谱和红外光谱对其结构进行了表征,将其应用到以电喷雾法制备Ti O2光阳极的染料敏化太阳能电池(DSSC)中,并测定了染料在Ti O2光阳极上的吸附量.结果表明,在AM 1.5 G的模拟光照下,基于染料CI的电池有更好的器件性能,短路电流(JSC)、开路电压(VOC)、填充因子(FF)和电池效率(η)分别为5.4 m A/cm2、0.73 V、0.58和2.3%.鉴于纯有机染料CBR和CI在350~450 nm区域的吸收较强,选择染料CBR或CI与传统染料N719共敏化,器件效率由5.2%(N719)分别提高到了5.6%(CBR-N719)和6.7%(CI-N719).     

Heteroleptic ruthenium complexes containing uncommon 5,5'-disubstituted-2,2'-bipyridine chromophores for dye-sensitized solar cells

Four new heteroleptic ruthenium sensitizers [Ru(4,4'-carboxylic acid-2,2'-bipyridine)(L)(NCS)(2)] (L = 5,5'-bis(4-octylthiophen-2-yl)-2,2'-bipyridine (1), 5,5'-bis(N,N-diphenyl-4-aminophenyl)-2,2'-bipyridine (2), 5,5'-bis(5-(N,N-diphenyl-4-aminophenyl)-thiophen-2-yl)-2,2'-bipyridine (3) and 5,5'-bis(4-octyl-5-(N,N-diphenyl-4-aminophenyl)-thiophen-2-yl)-2,2'-bipyridine (4)) were synthesized, characterized by physicochemical and computational methods, and utilized as photosensitizers in nanocrystalline dye-sensitized solar cells (DSSCs). The λ(max) of the metal-to-ligand charge transfer (MLCT) absorption of these four ruthenium dyes (527 nm for 1, 535 nm for 2, 585 nm for 3 and 553 nm for 4) can be tuned by various structural modifications of the ancillary ligand and it was shown that increasing the conjugation length of such ligand reduces the energy as well as the molar absorption coefficient of the MLCT band. The maximum incident photon to current conversion efficiency (IPCE) of 41.4% at 550 nm, 38.6% at 480 nm, 39.4% at 470 nm and 31.1% at 480 nm for 1-, 2-, 3- and 4-sensitized solar cells were obtained. Respectable power conversion efficiencies of 3.00%, 2.51%, 2.00% and 2.03% were realized, respectively, when the sensitizers 1, 2, 3 and 4 were used in DSSCs under the standard air mass (AM) 1.5 sunlight illumination (versus 5.9% for standard N719).     

Efficient thiocyanate-free sensitizer: a viable alternative to N719 dye for dye-sensitized solar cells

We have designed and synthesized a new thiocyanate-free sensitizer coded as SPS-01 and used it as the sensitizer in a TiO(2) based nanocrystalline dye-sensitized solar cell (DSSC). SPS-01 exhibits strong visible absorption properties with maximum peak around at 532 nm. The overall power conversion efficiency (PCE) of a DSSC sensitized with SPS-01 (7.96%) is higher than that of N719 (7.30%) under identical experimental conditions. This high PCE is attributed mainly due to the improvement in the short circuit current.     

苯基磷酸联吡啶钌络合物敏化纳晶多孔TiO2薄膜电极光电性能研究

用有机光敏染料敏化半导体,通过染料分子的吸附功能基团与半导体相互作用,使染料分子与半导体表面之间建立电性耦合,进行有效的电荷转移,可以形成有机-半导体复合新型光电功能材料。联吡啶钌络合物有较强的可见光吸收、氧化还原性能可逆、氧化态稳定性高,是一类性能优越的有机光敏染料。近来许多研究发现,羧酸联吡啶钌的强吸附与TiO₂纳晶薄膜的大比表面相结合,导致光生电荷快速注入TiO₂导带达到有效的电荷分离,得到了接近100%的单色光光电流效率^[1]。为研究联吡啶钌分子的不同吸附功能基团与TiO₂纳晶薄膜表面的相互作用对提高光电性能的影响,本文报道苯基磷酸取代的联吡啶钌络合物敏化纳晶多孔TiO₂薄膜的光电性能。     

Efficient co-sensitization of nanocrystalline TiO(2) films by organic sensitizers

Dye-sensitized solar cells based on co-sensitization of organic dyes having complementary spectral absorption in the visible region resulted in a panchromatic response, which exhibited 86% incident monochromatic photon-to-current conversion efficiency in the visible region; the optimized cell gave a short circuit current density of 15.5 mA cm(-2), an open circuit voltage of 685 mV and a fill factor of 0.70 corresponding to an overall conversion efficiency of 7.43% under solar simulated light irradiation of 100 mW cm(-2).     

Enhanced light harvesting efficiencies of bis(ferrocenylmethyl)-based sulfur rich sensitizers used in dye sensitized TiO2 solar cells

In this work, the photosensitizing properties of ferrocene (Fc)-based compounds FcCH(2)CS(3)CH(2)Fc (1) and FcCH(2)SSCH(2)Fc (2) were investigated and significant enhancement in the light harvesting efficiency was observed compared to those achieved with previously reported compounds from our lab. The compounds were fully characterized by spectroscopy and X-ray crystallography, and their electrochemical properties studied. DSSCs based on these dyes display efficiencies comparable to those of a standard cell based on N719 under similar experimental conditions. These studies demonstrate that ferrocenyl-based sulfur rich compounds with proper orientation of the Fc groups assisted via suitable linkers, together with desired redox properties and visible region electronic absorption features could constitute a new class of photosensitizers targeting light driven reactions.     

High-Performance Dipolar Organic Dyes with an Electron-Deficient Diphenylquinoxaline Moiety in the π-Conjugation Framework for Dye-Sensitized Solar Cells

We report here the synthesis and electrochemical and photophysical properties of a series of easily prepared dipolar organic dyes and their application in dye-sensitized solar cells (DSSCs). For the six organic dyes, the molecular structures comprised a triphenylamine group as an electron donor, a cyanoacrylic acid as an electron acceptor, and an electron-deficient diphenylquinoxaline moiety integrated in the π-conjugated spacer between the electron donor and acceptor moieties. The incorporation of the electron-deficient diphenylquinoxaline moiety effectively reduces the energy gap of the dyes and broadly extends the spectral coverage. DSSCs based on dye 6 produced the best overall cell performance of 7.35?%, which translates to approximately 79?% of the intrinsic efficiency of the DSSCs based on the standard N719 dye under identical experimental conditions. The high performance of DSSCs based on dye 6 among the six dyes explored is attributed to the combined effects of high dye loading on a TiO(2) surface, rapid dye regeneration, and effective retardation of charge recombination.     

Panchromatic ruthenium sensitizer based on electron-rich heteroarylvinylene π-conjugated quaterpyridine for dye-sensitized solar cells

The first example of a heteroarylvinylene π-conjugated quaterpyridine Ru(II) sensitizer (N1044) was synthesized and used in dye-sensitized solar cells; the dye has an effective panchromatic absorption band, covering the entire visible spectrum up to the NIR region, and superior electrochemical characteristics (HOMO/LUMO and bandgap energies) with respect to previous representative Ru(II) bi- and quaterpyridine sensitizers. A record IPCE curve ranging from 360 to 920 nm has been measured with a maximum of 65% at 646 nm and still 33% efficiency at 800 nm; this leads to substantially increased photocurrent (19.2 mA cm(-2)) when compared to the prototype N719 Ru(II) sensitizer.     

Coupling of titania inverse opals to nanocrystalline titania layers in dye-sensitized solar cells

We report a quantitative comparison of the photoaction spectra, short circuit current densities, and power conversion efficiencies of dye-sensitized solar cells (DSSCs) that contain bilayers of nanocrystalline TiO2 (nc-TiO2) and titania inverse opal photonic crystals (PCs). Cells were fabricated with PC/nc-TiO2 and nc-TiO2/PC bilayer films on glass/tin oxide anode of the cell, as well as in a split configuration in which the nc-TiO2 and PC layers were deposited on the anode and cathode sides of the cell, respectively. Incident photon current efficiencies at single wavelengths and current-voltage curves in white light were obtained with both cathode and anode side illumination. The results obtained support a model proposed by Miguez and co-workers, in which coupling of the low refractive index PC layer to the higher index nc-TiO2 layer creates a standing wave in the nc-TiO2 layer, enhancing the response of the DSSC in the red region of the spectrum. This enhancement is very sensitive to the degree of physical contact between the two layers. A gap on the order of 200 nm thick, created by a polymer templating technique, is sufficient to decouple the two layers optically. The coupling of the nc-TiO2 and PC layers across the gap could be improved slightly by treatment with TiCl4 vapor. In the bilayer configuration, there is an enhancement in the IPCE across the visible spectrum, which is primarily caused by defect scattering in the PC layer. There is also an increase of 20-50 mV in the open circuit photovoltage of the cell. With anode side illumination, the addition of a PC layer to the nc-TiO2 layer increased the efficiency of DSSCs from 6.5 to 8.3% at a constant N719 dye loading of 155-160 nmol/cm2.     

A convenient route to high area, nanoparticulate TiO2 photoelectrodes suitable for high-efficiency energy conversion in dye-sensitized solar cells

Ethanol-soluble amphiphilic TiO(2) nanoparticles (NPs) of average diameter ～9 nm were synthesized, and an α-terpineol-based TiO(2) paste was readily prepared from them in comparatively few steps. When used for fabrication of photoelectrodes for dye-sensitized solar cells (DSSCs), the paste yielded highly transparent films and possessing greater-than-typical, thickness-normalized surface areas. These film properties enabled the corresponding DSSCs to produce high photocurrent densities (17.7 mA cm(-2)) and a comparatively high overall light-to-electrical energy conversion efficiency (9.6%) when deployed with the well-known ruthenium-based molecular dye, N719. These efficiencies are about ～1.4 times greater than those obtained from DSSCs containing photoelectrodes derived from a standard commercial source of TiO(2) paste.     

Kinetics of electron recombination of dye-sensitized solar cells based on TiO2 nanorod arrays sensitized with different dyes

The performance and electron recombination kinetics of dye-sensitized solar cells based on TiO(2) films consisting of one-dimensional nanorod arrays (NR-DSSCs) which are sensitized with dyes N719, C218 and D205, respectively, have been studied. It has been found that the best efficiency is obtained with the dye C218 based NR-DSSCs, benefiting from a 40% higher short-circuit photocurrent density. However, the open circuit photovoltage of the N719 based cell is 40 mV higher than that of the organic dye C218 and D205 based devices. Investigation of the electron recombination kinetics of the NR-DSSCs has revealed that the effective electron lifetime, τ(n), of the different dye based NR-DSSCs shows the sequence of C218 > D205 > N719. The higher V(oc) with the N719 based NR-DSSC is originated from the more negative energy level of the conduction band of the TiO(2) film. In addition, in comparison to the DSSCs with the conventional nanocrystalline particles based TiO(2) films, the NR-DSSCs have shown over two orders of magnitude higher τ(n) when employing N719 as the sensitizer. Nevertheless, the τ(n) of the DSSCs with the C218 based nanorod arrays is only ten-fold higher than that of the nanoparticles based devices. The remarkable characteristic of the dye C218 in suppressing the electron recombination of DSSCs is discussed.     

Hierarchical TiO2 Flower-spheres with Large Surface Area and High Scattering Ability: an Excellent Candidate for High Efficiency Dye Sensitized Solar Cells

Hierarchical TiO₂ flower-spheres assembled from porous nanosheets-stacked of nanoparticles were synthesized by a simple hydrothermal method with one-step. The as-prepared TiO₂ flower-spheres showed a diameter range from 200 nm to 550 nm and a large surface area of 188 m²/g. A double layer photoanode made of P25 nanoparticles and as-prepared TiO₂ flower-spheres was fabricated for the dye sensitized solar cells(DSSCs). The efficient light scattering and dye absorption of the photoanode can be attributed to the top-layer of hierarchical TiO₂ flower-spheres. DSSCs based on the double layers photoanode exhibit a higher energy conversion efficiency of 8.11% with a short-circuit photocurrent density of 17.87 mA/cm², indicating that there is an increase of 38% in the conversion efficiency compared to those based on electrode P25(5.91%, 14.09 mA/cm²).     

Improvement of dye-sensitized solar cells' performance via co-sensitization of new azo thiazole organic dyes with ruthenium (II) based N-719 dye

Three novel azo thiazole organic dyes, NA-1–3, have been synthesized and utilized as co-sensitizers in dye-sensitized solar cells (DSSCs). These co-sensitizers were designed with a thiazole ring π-bridge that mediates between the diazo (–N = N–) functional group and carboxylic acid anchoring unit. They possess a rod-like molecular structure and exhibit strong UV–vis absorption near 600 nm. Co-sensitization studies were also conducted with the ruthenium complex N719. The co-sensitized DSSCs showed enhanced short-circuit and open-circuit photocurrents (Jsc) and voltages (Voc), resulting in more efficient photovoltaic performance compared to N719 (PCE 7.25%). Electrochemical impedance spectroscopy (EIS) and incident photon to current efficiency (IPCE) were employed to investigate the underlying reasons for these improvements. It was found that co-sensitization effectively reduced electron recombination, resulting in a higher Voc without compromising photocurrent loss.     

聚乙烯吡咯烷酮基碘凝胶电解质的制备及在染料敏化太阳能电池中的应用

采用聚乙烯吡咯烷酮(PVP)和聚偏氟乙烯(PVDF)为凝胶剂, 以碘化锂和碘单质为碘源, 碳酸乙烯酯(EC)和碳酸丙烯酯(PC)为溶剂, 制备了染料敏化太阳能电池(DSSCs)用凝胶聚合物电解质(GPE). 使用拉曼光谱、 循环伏安曲线和交流阻抗谱等对GPE进行表征. 结果表明, 聚合物的配比与浓度及碘与碘化锂比例对该电解质性能有很大影响, 当聚合物质量分数为10%、 PVP与PVDF质量比为80∶20、 I₂浓度为0.042 mol/L且LiI与I₂摩尔比为30∶1时, 制备的GPE在室温下电导率达最大值(3.27 mS/cm). 使用该GPE组装的DSSCs在100 mW/cm²的模拟太阳光照射下, 开路电压为0.64 V, 短路电流为13.6 mA/cm², 填充因子为0.595, 能量转化效率为5.18%, 并在30 d内表现出了良好的稳定工作性能.