多组分纳米纤维体系中载流子动力学的有效级联调制及其高效光催化产氢性能研究（英文）

利用半导体作为催化剂,将水光催化还原为H₂,为缓解全球能源危机以及环境污染问题提供了一种经济环保的途径。优化调控载流子动力学行为对提高半导体光催化分解水还原为绿色燃料-H₂的活性具有十分重要的意义。目前,基于半导体异质结效应或局域表面等离激元共振的敏化过程来设计和调控半导体基异质结构体系已成为调控载流子动力学行为的一种经典策略。然而,通过精细设计异质结构,合理耦合上述敏化过程,实现载流子动力学的级联调制,从而获得高效的光催化产H₂活性仍然任重道远。在本文中,我们通过原位氧化(g-C₃N₄的剥离和Ag₂S)和还原(Ag)反应,将等离激元Ag纳米颗粒(NPs)和两种不同的半导体Ag₂SNPs和g-C₃N₄纳米片(NSs)组装在电纺TiO₂纳米纤维(NFs)中,形成了一种新型四元异质组分纳米纤维(HNFs)体系。结合时间分辨光致发光光谱,3D时域有限差分模拟以及对照实验,我们...     

二氧化钛纳米颗粒/还原氧化石墨烯修饰玻碳电极在对硝基苯酚检测中的应用

本文报道了用二氧化钛纳米颗粒（TiO₂NPs）/还原氧化石墨烯（RGO）的复合物修饰玻碳电极检测微量对硝基苯酚（4-NP）的电化学方法. 本研究用扫描电子显微镜（SEM）对该复合材料形貌进行表征,用循环伏安法和交流阻抗谱对该复合物电极的电化学性能进行检测,表现出良好的电化学特性,采用差分脉冲伏安法对4-NP进行微量检测,结果令人满意,这主要得益于TiO2NPs/RGO复合物对4-NP有较高的催化活性,其电流峰值与浓度呈较高的线性关系,DPV的检测范围为10μmol·L^-1 ~ 350μmol·L^-1,检测限为0.13 μmol·L^-1. 与其他报道的一些电化学传感器相比,该传感器检测范围大,检测限低,且工作稳定,成本低,分析简单快速,具有很好的应用前景.     

贵金属在Ag_2S纳米颗粒中由内向外的迁移现象

纳米颗粒具有明显区别于块体材料的新奇特性,本文利用透射电镜观察,描述并讨论一种发生在贵金属(Au、Ag、Pd和Pt)和硫化银(Ag_2S)构成的核壳结构纳米颗粒中的有趣现象,即贵金属在Ag_2S纳米颗粒中由内向外的迁移。迁移可在室温下进行,其最终结果使最初的核壳结构颗粒演变成由贵金属和Ag_2S构成的异质纳米二聚体结构,如Au-Ag_2S、Ag-Ag_2S、PdAg_2S和Pt-Ag_2S。电镜表征表面实验条件下贵金属在Ag_2S的迁移类似于一种整体迁移的模式且迁移过程中伴随着颗粒形貌结构的演变。贵金属在Ag_2S中的经空位互换的扩散机制或半导体纳米颗粒的自纯化机制可以用来解释这种迁移现象。     

Ag/Ag_3PO_4/g-C_3N_4复合光催化剂的合成与再生及其可见光下的光催化性能(英文)

研究了用离子交换沉淀法制备的Ag/Ag3PO4/g-C3N4的可见光光催化性能及再生方法.通过X射线衍射(XRD)、场发射扫描电子显微镜(FESEM)、紫外-可见(UV-Vis)吸收光谱及X射线光电子能谱(XPS)对其进行了结构特性分析.XRD结果显示再生后催化剂的结构未发生改变.FESEM及UV-Vis分析结果说明催化剂由Ag3PO4与g-C3N4复合而成.XPS分析结果表明催化剂表面出现少量的银单质.利用可见光(λ420nm)照射下的苯酚降解实验评价了样品的光催化活性,并通过活性物种及能带结构的分析对催化剂的光催化机理进行了推测.研究表明,Ag/Ag3PO4/g-C3N4的光催化活性明显高于纯Ag3PO4及纯g-C3N4,主要原因归结为单质银、Ag3PO4及g-C3N4的协同效应.经过氧化氢和磷酸氢铵钠(NaNH4HPO4)的再生可完全恢复催化剂的活性,这表明该绿色环保的再生方法可实现Ag/Ag3PO4/g-C3N4催化剂在环境中的实际应用.     

Kinetics and mechanism of the reaction between silver(III) and thiourea in aqueous alkaline media

The tetrahydroxoargentate(III) ion, Ag(OH)₄⁻, is rapidly reduced by thiourea (tu) in accordance with the three term rate law RATE = {k₁+(k₂+k₃[OH⁻])[tu]}[Ag^III] where k₁ = 1.08 s⁻¹, k₂ = 1.46 x 10³ M⁻¹ s⁻¹, and k₃ = 2.02 x 10³ M⁻² s⁻¹. The k₁ path occurs via the rate-determining aquation of Ag(OH)₄⁻ while the other two paths involve axial attack of thiourea on silver. The higher values of k₂ and k₃ compared to the ethylenediamine reaction, which obeys the same rate law, is a reflection of the greater nucleophilicity of tu.

Following the redox reaction, solutions become brown in a reaction that obeys pseudo-first-order kinetics. Similar behaviour is observed when tu is replaced by Na₂S or thio-acetamide and when Ag^I reacts with any of these sulphur containing compounds. We attribute this process to the Ag^I promoted formation of sulphide species which eventually precipitate as Ag₂S.     

太阳光响应型Ag2S/Ag3PO4复合材料的制备及催化降解水杨酸

以AgNO₃, Na₂HPO₄和硫粉为原料, 采用共沉淀-水热法合成了具有太阳光响应型Ag₂S/Ag₃PO₄复合材料, 运用扫描电子显微镜(SEM)、 X射线粉末衍射(XRD)、 X射线光电子能谱(XPS)和紫外-可见漫反射(UV-Vis DR)光谱等方法对样品进行了表征, 并在模拟太阳光条件下, 考察了Ag₂S/Ag₃PO₄对水杨酸的光催化降解效率. 结果表明, 与Ag₃PO₄相比, Ag₂S的负载量为1%(质量分数)时Ag₂S/Ag₃PO₄粒径变小, 呈立方晶相结构; Ag₂S/Ag₃PO₄复合材料可以有效促进光生电子-空穴分离, 使Ag₃PO₄禁带宽度降低到2.24 eV, 并增强了可见光的吸收能力. 在Ag₂S负载量为1%, 120 ℃水热4 h条件下, Ag₂S/Ag₃PO₄复合材料具有最佳光催化活性, 经模拟太阳光照射60 min对10 mg/L的水杨酸去除率达到88.2%.     

Ag/Ag2WO4等离子体共振催化剂可见光催化还原CO2

转化CO₂为有机组分是缓解全球变暖和保障持续能源供给的有效方法之一.采用简易的离子交换结合水合肼还原法制备了一系列不同晶相Ag₂WO₄载银(Ag/Ag₂WO₄)的等离子共振光催化剂,并用X射线衍射(XRD)、X射线光电子能谱(XPS)、扫描电子显微镜-能量色散X射线光谱(SEM-EDS)、紫外-可见(UV-Vis)吸收光谱和比表面积测试对催化剂进行了表征.较之Ag₂WO₄, Ag/Ag₂WO₄在可见光催化还原CO₂生成CH₄时显示了明显提高的量子产率(QY)、能量投入产出比(EROEI)、转换数(TON),就Ag/α-Ag₂WO₄, Ag/β-Ag₂WO₄和Ag/γ-Ag₂WO₄而言,最佳催化剂为Ag/β-Ag₂WO₄,其实际最佳Ag:Ag₂WO₄摩尔比为4:96,该催化剂还原CO₂为CH₄的QY、EROEI、TON和拟一级反应速率常数分别为0.145%、0.067%、9.61和1.96×10^-6 min^-1.此外,制备的等离子共振Ag/Ag₂WO₄光催化剂在可见光辐照下进行循环反应仍能保持稳定性.局域表面等离子共振效应是强化Ag/Ag₂WO₄光催化剂活性和稳定性的主要原因.     

Dealloyed Silver Nanoparticles as Efficient Catalyst Towards Oxygen Reduction in Alkaline Solution

Silver nanoparticles(Ag NPs) were prepared by dealloying Mg-Ag alloy precursor. The obtained Ag NPs have an average ligament size of (50±10) nm. Electrocatalytic activity of Ag NPs towards oxygen reduction reaction(ORR) in 0.1 mol/L NaOH solution was assessed via cyclic voltammetry(CV), rotating ring disk elec-trode(RRDE) techniques, and electrochemical impedance spectroscopy(EIS). The electrochemical active area for the ORR was evaluated by means of the charge of the underpotential deposition(UPD) of lead(Pb) on Ag NPs. The CV results indicate that Ag NPs have a higher current density and more positive onset potential than the bulk Ag electrode. RRDE was employed to determine kinetic parameters for O₂ reduction. Ag NPs exhibit a higher kinetic current density of 25.84 mA/cm² and a rate constant of 5.45×10^-2 cm/s at -0.35 V vs. Hg/HgO. The number of electrons(n) involved in ORR is close to 4. Further, EIS data show significantly low charge transfer resistances on the Ag NPs electrode. The results indicate that the prepared Ag NPs have a high activity and are promising catalyst for ORR in alkaline solution.     

磁性AgBr/Ag3PO4/ZnFe2O4复合催化剂的制备及光催化性能

水热法结合原位沉淀法成功制备新型磁性溴化银/磷酸银/铁酸锌(AgBr/Ag₃PO₄/ZnFe₂O₄)复合催化剂,并通过X射线衍射、能量色散X射线、场发射扫描电子显微镜、透射电子显微镜和紫外-可见漫反射光谱对其晶相结构、组成、形貌及吸光性能进行了表征。在可见光照射下,所制备的AgBr/Ag₃PO₄/ZnFe₂O₄复合催化剂光催化降解罗丹明B (RhB)的活性优于Ag3PO4/ZnFe₂O₄、AgBr/ZnFe₂O₄和P25 TiO₂。在酸性和碱性溶液中,AgBr/Ag₃PO₄/ZnFe₂O₄光催化剂呈现出优良光催化性能。在AgBr/Ag₃PO₄/ZnFe₂O₄体系中,光催化降解RhB的速率随着反应体系温度的升高而增大,由阿伦尼乌斯方程计算获得反应体系活化能为31.9 kJ·mol^-1。AgBr/Ag₃PO₄/ZnFe₂O₄复合材料优异的可见光催化活性归因于光生电荷的有效分离,所产生的超氧自由基和空穴是RhB降解的主要活性物种。     

无定型钼硫化物/还原氧化石墨烯的辐射合成及其电催化析氢性能

钼硫化物被认为是一种高效的电催化析氢反应的催化剂,因此其合成方法受到了广泛的研究和关注。本文以四硫代钼酸铵和氧化石墨为前驱体,利用γ射线对其辐照还原,一步法制备了钼硫化物/还原氧化石墨烯(Mo S_x/RGO)复合材料。通过X射线光电子能谱、X射线衍射、透射电子显微镜、Raman光谱等表征手段确认复合材料中的Mo Sx为无定型结构,且氧化石墨烯得到了有效的还原。同时系统研究了吸收剂量、前驱体配比对复合材料作为析氢反应催化剂性能的影响。结果发现,Mo Sx/RGO复合材料具有优异的催化性能,其催化起始电压为110 m V,在电流密度为10 m A·cm~(-2)时过电势仅为160 m V,Tafel斜率为46 m V·dec~(-1),说明该催化剂催化析氢机理为Volmer-Heyrovesy机理。此外,Mo Sx/RGO复合材料还具有良好的催化稳定性。     

Interfacial properties of precipitate-based ion-selective electrodes : Rotating disk impedance measurements of the Ag2S/Ag (aqueous) interface

Three-electrode rotating disk impedance measurements were made from 31.6 kHz to 0.0178 Hz on Ag₂S/Ag⁺ (aqueous) and Ag₂S/Ag systems. Membranes were prepared from materials precipitated in excess of silver or sulfide ions, and stoichiometric mixtures. Impedances were analyzed, as a function of rotation rate and bathing activities, to isolate bulk conductivities, internal diffusion, surface kinetic and dissolution/crystallization impedances. High-frequency bulk resistivities, R_∞, varied by four with precipitation and pressing conditions. Resistivities were the same for solution and ohmic configurations for each preparation. For ohmic contacts, R_∞ and R(DC) were identical. Solution contact cells in 10^-1 M and 10^-2 M bathing silver ion solution gave identical frequency-dependent impedances which were independent of rotation rate. Thus, solution diffusional impedances and solution dependent surface kinetics were eliminated, and a finite Warburg, interior-Ag⁺-defect, diffusion impedance was indicated. Summation of bulk membrane and contact resistances, and this Warburg impedance served as a 'background' correction in analyzing dilute bathing solution interfacial impedances for surface effects. Corrected impedances in 10^-3 –10^-5 M AgNO₃ showed solution diffusional behaviour combined with surface kinetic and dissolution impedances. An iterative linear least-squares method resolved these quantities. The surface resistance suggests a potential-dependent rate constant; dissolution time constants were solution-independent and smaller than those for solution diffusion. Thus, dissolution can be a rate-limiting step in establishment of steady-state potentials.     

CuS/Ag2S纳米复合物的制备及类过氧化物酶性质

采用水热法合成了一种微球状的CuS/Ag₂S纳米复合物. 通过透射电子显微镜、 紫外-可见吸收光谱和拉曼光谱等对其形貌及光学性质进行了表征; 考察了其类过氧化物酶性质, 并通过表面增强拉曼散射原位监测了类过氧化物酶催化反应. 以3,3',5,5'-四甲基联苯胺(TMB)为底物进行显色反应, 结果表明, 在H₂O₂存在下CuS/Ag₂S 纳米复合物具有类过氧化物酶的性质, 可以将无色的TMB氧化成蓝色的oxTMB. 基于此实现了对微量H₂O₂的检测.     

An efficient and easily retrievable dip catalyst based on silver nanoparticles/chitosan-coated cellulose filter paper

Re-use of a catalyst is an important task, which is usually achieved by loading it on easily separable supports such as magnetic substrates. However, we demonstrate here the process of easy and fast catalyst separation from a reaction medium by loading it onto an economically feasible and microscopically high surface substrate of filter paper (FP) made up of cellulose microfibers as catalyst support. To achieve the goal, we coated chitosan (CH) on filter paper (CH-FP) to impart a high affinity of the substrate for metal ion absorption. AgNO₃ dissolved in water with a 0.1 M concentration was used as the Ag ion carrier solution, and CH-FP strips with known rectangular dimensions were submerged into it for the metal ion absorption. The metal ion-laden CH-FP strips were dip treated with sodium borohydride (NaBH₄) aqueous solution to prepare Ag-nanoparticle loaded CH-FP (Ag/CH-FP). X-ray diffraction and energy dispersive X-ray spectroscopy confirmed the formation of the Ag/CH-FP hybrid. Ag/CH-FP morphology was examined through scanning electron microscopy analysis, which showed the presence of Ag nanoparticles attached to the cellulose microfibers. The prepared Ag/CH-FP was employed as a dip catalyst for the degradation of nitroarene compounds of 2-nitophenol (2-NP) and 4-nitrophenol (4-NP) by NaBH₄. Remarkably, the rate constants for 4-NP and 2-NP were 3.9 × 10^?3 and 1.7 × 10^?3 s^?1, respectively. In addition, we discussed the ease of the catalyst retrievability from the reaction mixture and its re-usability.     

还原氧化石墨烯/TiO2复合材料在钠离子电池中的电化学性能

二氧化钛(TiO₂)作为有前景的钠离子电池负极材料, 具有良好的循环稳定性, 但由于其导电率较低, 而导致容量和倍率性能不佳限制了其实际应用. 本文采用喷雾干燥技术制备了氧化石墨烯/纳米TiO₂复合材料(GO/TiO₂), 通过热处理获得还原氧化石墨烯/TiO₂复合材料(RGO/TiO₂). 电化学测试结果表明, 还原氧化石墨烯改性的RGO/TiO₂复合材料的电化学性能得到显著提升, RGO含量为4.0%(w)的RGO/TiO₂复合材料在各种电流密度下的可逆容量分别为183.7 mAh·g^-1 (20 mA·g^-1), 153.7 mAh·g^-1 (100 mA·g^-1)和114.4 mAh·g^-1 (600mA·g^-1), 而纯TiO₂的比容量仅为93.6 mAh·g^-1 (20 mA·g^-1), 69.6 mAh·g^-1 (100 mA·g^-1)和26.5 mAh·g^-1 (600mA·g^-1). 4.0%(w) RGO/TiO₂复合材料体现了良好的循环稳定性, 在100 mA·g^-1电流密度下充放电循环350个周期后, 比容量仍然保持146.7 mAh·g^-1. 同等条件下, 纯TiO₂电极比容量只有68.8 mAh·g^-1. RGO包覆改性极大提高了TiO₂在钠离子电池中的电化学嵌钠/脱钠性能. RGO包覆改性技术在改进钠离子电池材料性能中将有很好的应用前景.     

Complexes of cationic coinage metal clusters Mn (M=Cu, Ag, Au; n=1–4) and H2S: a theoretical study

Geometries and vibrational frequencies of complexes of cationic coinage metal clusters M_n⁺ (M=Cu, Ag, Au; n=1–4) and H₂S are computed using density functional theory. Thermochemical values for M_n⁺H₂S decomposition channels involving loss of an H atom, H₂ molecule, M atom, or M₂ molecule are also computed. Significantly different results are obtained for closed-shell (n odd) and open-shell (n even) complexes.     

YSZ传导膜H_2S固体氧化物燃料电池

研究了Y2O3稳定的ZrO2(YSZ)氧离子传导膜H2S固体氧化物燃料电池性能。掺杂NiS、电解质、Ag粉和淀粉制备了双金属复合MoS2阳极催化剂,掺杂电解质、Ag粉和淀粉制备了复合NiO阴极催化剂,用扫描电镜对YSZ和膜电极组装(MEA)进行了表征,比较了不同电极催化剂的性能和极化过程,考察了不同温度对电池性能的影响。结果表明,双金属复合MoS2/NiS阳极催化剂在H2S环境下比Pt和单金属MoS2催化剂稳定,复合NiO阴极催化剂比Pt性能好,在电极催化剂中加入Ag可显著提高电极的导电性;与Pt电极相比,复合MoS2阳极和复合NiO阴极催化剂的过电位较小,阳极的极化比阴极侧小;温度升高,电池的电流密度与功率密度增加,电化学性能变好。在750℃、800℃、850℃和900℃及101.13 kPa时,结构为H2S、(复合MoS2阳极催化剂)/YSZ氧离子传导膜/(复合NiO阴极催化剂)、空气的燃料电池最大功率密度分别为30 mW/cm2、70 mW/cm2、155 mW/cm2及295 mW/cm2、最大电流密度分别为120 mA/cm2、240 mA/cm2、560 mA/cm2和890 mA/cm2。     

可见光响应的Co3(PO4)2/Ag3PO4纳米复合光催化剂的制备及表征

采用简单的化学偏聚法合成出Ag3PO4纳米颗粒、磷酸钴(Co3(PO4)2,CoP)纳米片以及它们两者的纳米复合结构(CoP/Ag3PO4),同时还比较了它们的可见光催化活性.采用场发射扫描电镜(FESEM)、X射线衍射(XRD)、紫外-可见(UV-Vis)吸收光谱以及光致发光谱等手段对其形貌、结构、光学以及可见光催化性能等进行表征.结果表明,CoP/Ag3PO4复合纳米结构的可见光降解甲基橙(MO)的速率和循环稳定性均明显优于其它两种物质.这表明CoP应该起着共催化剂的作用,它能够抑制光生电子与空穴之间的复合,并且提供大量高活性的光生空穴.此外,我们还发现CoP/Ag3PO4降解另一种阳离子型染料——罗丹明B(RhB)的能力则远不如纯Ag3PO4,这可能是与光催化剂的表面性质发生改变有关,造成更低的RhB吸附能力.本文提供了一种廉价制备高效可见光催化剂的新方法.     

硫化氢对钴改性活性焦脱除煤气中汞的影响机理

采用等体积浸渍煅烧法制备钴改性活性焦(Co-AC),并采用BET、XRD等分析手段进行表征。 利用固定床吸附实验台,研究了模拟煤气(N₂、H₂、CO、H₂S)气氛下汞的吸附特性,重点关注H₂S对汞吸附的影响。 结果表明,5%负载量的Co-AC在120 ℃和H₂S作用下具有优异的脱汞能力,2 h内平均脱汞效率高达97.8%。 此外基于密度泛函理论,首先计算了H₂S、HS及S在Co₃O₄(110)表面的吸附能及键长,通过比较H—S键键长的变化得出H₂S会逐步解离成HS与S,然后将优化后的S-Co₃O₄(110)作为Hg的吸附基底,研究其吸附特性,得出Hg与S反应生成稳定的HgS,吸附能为-3.503 eV,证明了汞的吸附遵循Eley-Rideal机制。 Co-AC吸附剂在高温下脱汞性能受到极大的抑制,因为随吸附温度升高,表面活性硫的减少及硫和汞的反应平衡常数下降显著,导致汞的脱除能力下降。 本文采用了实验加模拟的手段,探明了H₂S存在时Hg⁰在钴基吸附剂表面的反应机理,为协同脱除煤气中的H₂S和Hg⁰提供了理论指导。     

Colorful Silver/Carbon Nitride Composites Obtained by Photoreduction

The Ag⁺ photoreduction by graphitic carbon nitride(g-CN) materials in a high concentration of Ag⁺ solution is reported, and a series of colorful Ag/g-CN composites is prepared and characterized. The chromatic change correlates to the carbon nitride materials synthesized at different heating temperatures(CN_T, where T means heating temperature), taking advantage of the different photocatalytic activities of different CN_T. The mechanism beneath this phenomenon is attributed to two factors:the particle size of Ag NPs and the coordinate effect of Ag NPs on CN_T sheets. Interestingly, the multi-colors of Ag/g-CN composites display only on the CN_T materials synthesized from heating melamine-cyanuric acid precursor, but not on the CN_T from heating pure melamine. The color of the as-prepared Ag/g-CN composites can endure the corrosion of HNO₃ and ethanol, which shows a good chemical stability and may hint its application as chromophores.     

Highly Selective and Active Pd‐In/three‐dimensional Graphene with Special Structure for Electroreduction CO2 to Formate

Electrocatalytic reduction of CO₂ to formate on carbon based electrodes is known to suffer from low electrochemical reaction activity and product selectivity. Pd/three‐dimensional graphene (Pd/3D‐RGO), In/3D‐RGO and Pd‐In/3D‐RGO for the electrochemical reduction of CO₂ were prepared by a mild method that combines chemical and hydrothermal. The metal/3D‐graphenes (metal/3D‐RGO) were characterized by scanning electron microscopy, X‐ray diffraction, transmission electron microscopy and X‐ray photoelectron spectroscopy (XPS). Cyclic voltammetry and the ion chromatography were performed to investigate the electrochemical performance of the metal/3D‐RGO. The morphology and dispersion of metal/3D‐RGO are 3D structure with amount of interconnected pores with metal NPs loading on the fold. And the Pd_0.5‐In_0.5/3D‐RGO show excellent surface performance with well dispersion and smallest particle size (12.8 nm). XPS reveal that binding energy of Pd (In) NPs is shifted to negative energy, for the metal lose electrons in metal and combine with C, which is demonstrated in the HNO₃ experiment. The peak potential of Pd_0.5‐In_0.5/3D‐RGO is −0.70 V (vs. Ag/AgCl), which is more positive than In_1.0/3D‐RGO (−0.73 V) and Pd_1.0/3D‐RGO (−1.2 V). The highest faradaic efficiency (85.3 %) happens in Pd_0.5‐In_0.5/3D‐RGO at −1.6 V vs. Ag/AgCl. In these experiments, the special structure that metal NPs combine with C and the bimetal NPs give a direction to convert CO₂ to formate.