Effect of vinyltriethoxysilane addition on the pyrolytic conversion of tetraethoxysilane based silica gel

The effect of vinyltriethoxysilane (VTES) addition on the pyrolytic conversion of tetraethoxysilane (TEOS) based silica gel had been studied. Thermogravimetric analysis coupled with mass spectroscopy was carried out to study the thermal decomposition behavior of precursor gels. The ceramic yield of precursor gels was decreased with the increase of the VTES content. ²⁹Si magic angle spinning nuclear magnetic resonance indicated that the incorporation of VTES into TEOS not only changed the composition and structure of precursor gels, but also increased carbon-enriched SiO _x C_4?x units of silicon oxycarbide ceramics during the pyrolysis conversion. The carbon content of SiOC ceramic was almost unchanged between 1,000 and 1,500 °C. However, the O/Si ratio of the silicon oxycarbide ceramic was reduced and the free carbon content was increased with the increasing molar ratios of VTES/TEOS. Moreover, the carbothermal reduction reaction led to the free carbon content decreased with the increase of the sintering temperature.     

Micropatterning of Inorganic-Organic Hybrid Coating Films from Various Tri-Functional Silicon Alkoxides with a Double Bond in Their Organic Components

Inorganic-organic hybrid coating films were prepared from various trifunctional silicon alkoxides with a C=C double bond in their organic components, such as vinyltriethoxysilane (VTES), allyltriethoxysilane (ATES) or trimethoxysilylpropylmethacrylate (TMSPM), and zirconium n-tetrapropoxide modified with methacrylic acid. UV light from a high-pressure mercury lamp was irradiated through a photomask on the hybrid films, and this irradiation increased refractive index and microhardness of the films and decreased solubility of the films in alcohol or alkaline solution. IR spectra of the coating films have shown that C=C bonds in these trifunctional silicon alkoxides were polymerized with the UV irradiation. Patterns with a width of about 10 m and thickness of about 5–15 m were formed by the etching of unirradiated region of the films. Since VTES and ATES have a shorter organic chain than TMSPM, the hybrid films prepared from VTES or ATES are expected to show small optical loss in the near-infrared region due to C—H bonds in their use as waveguides.     

Formation of an in situ nanosilica nanomatrix via graft copolymerization of vinyltriethoxysilane onto natural rubber

Natural rubber (NR) with an in situ nanosilica nanomatrix was characterized in present work. The in situ nanosilica nanomatrix was prepared via graft copolymerization of a silane monomer, vinyltriethoxysilane (VTES), onto deproteinized NR (DPNR) in latex stage using tetrapentamine (TEPA)/tert‐butylhydroperoxide (TBHPO) as initiators. VTES conversion of more than 80% was obtained, and it depended on VTES concentration. The graft copolymer structure was characterized by Fourier transform infrared (FT‐IR), solution‐state proton nuclear magnetic resonance (¹H‐NMR), and solid‐state ²⁹Si‐NMR spectroscopy. FT‐IR analysis of the graft copolymer confirmed the formation of in situ silica particles, while solution‐state ¹H‐NMR and solid‐state ²⁹Si‐NMR revealed the partial hydrolysis of the ethoxy groups and polycondensation of the silanol groups. The formation of nanosilica particles enhanced thermal and mechanical properties of the graft copolymer. Morphology observations of the in situ nanosilica nanomatrix through scanning electron microscopy (SEM) and transmission electron microscopy (TEM) indicated that the spherical nanosilica particles form a nanomatrix surrounding NR particle. The formation of the nanomatrix was proved to enhance mechanical properties for NR materials.     

Sintering Anomaly in Silica-Titania Sol-Gel Films

Sol-gel processing has been successfully applied to the preparation of silica-titania planar waveguides for integrated optics. In order to achieve low loss guides, proper densification is essential. A series of single layer silica-titania films were deposited by spin-coating on Si substrates from precursor sols prepared by mixing tetraethylorthosilicate (TEOS) with titanium tetra-iso-propoxide (TPOT). The thermal densification behavior of these thin gel films was followed by measuring their refractive index, by ellipsometry, as a function of the temperature, between 300–900°C and the heating time; an anomalous sintering behavior was found, consisting of a rapid initial rise in film density (calculated from the refractive index) at any heat-treatment temperature, followed by a pronounced minimum at times of the order of 3 minutes, after which the density slowly increased until the maximum plateau value, reached at each temperature.In order to explain the above sintering anomaly, a detailed compositional and structural characterization was performed on the films by infrared spectroscopy (IR) and X-ray photoemission spectroscopy (XPS). A redistribution of the Ti⁴⁺ ions within the film thickness was detected, which may in part explain the observed anomaly and has implications regarding the possible occurrence of phase separation during film sintering.     

含氟高分子/SiO2杂化疏水材料的制备及涂层表面性质

采用自由基溶液聚合与溶胶-凝胶法相结合的方法制备了含氟高分子/SiO2杂化疏水材料.通过甲基丙烯酸十二氟庚酯(FA)与乙烯基三乙氧基硅烷(VTES)共聚合成了含氟硅共聚物(PFAS),进一步通过原硅酸乙酯(TEOS)与PFAS共聚物溶液共水解缩聚制备了具有含氟侧基的碳碳主链高分子和硅氧网络的含氟高分子/SiO2杂化疏水材料.研究结果表明,SiO2组分含量提高可以显著增加杂化材料薄膜的涂敷厚度,改善其耐久性能,而对杂化材料疏水性能的影响不大.     

Poly(vinyltriethoxysilane) modified MWCNT/polyimide nanocomposites—Preparation,morphological, mechanical,and electrical properties

Multi‐walled carbon nanotube (MWCNT) modified by vinyltriethoxysilane (VTES) via free radical reaction has been prepared (poly (vinyltriethoxysilane) modified MWCNTs, PVTES‐MWCNT). Precursor of polyimide, polyamic acid has been synthesized by reacting 4,4′‐oxydianiline with 3,3′,4,4′‐benzophenone tetracarboxylic dianhydride. PVTES‐MWCNT were then mixed with polyamic acid and heated to 300 °C to form CNT/polyimide composite. During the imidization processes, the silanes on CNT surface reacted with each other and may be connected together by covalent bond (Si? O? Si). The PVTES‐MWCNT was analyzed by Fourier transform infrared and X‐ray photoelectron spectroscopy. The PVTES‐MWCNT/polyimide composites were analyzed by CP/MAS solid state ²⁹Si nuclear magnetic resonance (NMR) spectroscopy. Morphological properties of the PVTES‐MWCNT/polyimide composites were investigated by scanning electron microscope and transmission electron microscope. Electrical conductivity increased dramatically comparing to the unmodified MWCNT/polyimide composites. Mechanical properties of nanocomposite were enhanced significantly by PVTES‐MWCNT. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 803–816, 2008     

Unusual inorganic phase formation in ultraviolet‐curable organic–inorganic hybrid films

Inorganic–organic hybrid materials were prepared with a cycloaliphatic epoxide adduct of linseed oil with tetraethylorthosilicate (TEOS) oligomers via a cationic UV‐curing process. The TEOS oligomers were prepared in the presence of water and ethanol with hydrochloric acid as a catalyst. The TEOS oligomers were characterized with ¹H and ²⁹Si NMR and matrix‐assisted laser desorption/ionization time‐of‐flight mass spectrometry. Hybrid films were cured, and the dynamic mechanical and thermal properties of the hybrid films were evaluated as a function of the TEOS oligomer content. The morphology of the hybrid films was examined with atomic force microscopy, transmission electron microscopy, and small‐angle light scattering. The microscopy and dynamic mechanical data indicated that the hybrid films were heterogeneous materials with various inorganic particle sizes dispersed within the organic matrix. In addition, ²⁹Si solid‐state NMR spectroscopy was used to investigate the coupling between the silicate region and organic regions. A schematic model is proposed to address structural features of hybrid materials. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 1607–1623, 2005     

Preparation and Spectroscopy of Aluminosilicate Films Deposited on Graphite Surfaces via an Anhydrous Sol-Gel Route

Anhydrous aluminosilicate sols with Al : Si molar ratio ranging from 1 : 10 to 1 : 5 were prepared by a two-step anhydrous sol-gel process, in which tetraethoxysilane (TEOS) is pre-hydrolysed by formic acid, followed by addition of aluminium ethoxide. Unlike the case of aqueous sol-gel routes, where the Si–O–Al network homogeneity is greatly restricted by precipitation of Al(OH)₃, this anhydrous route yields clear, homogeneous sols. The sol formation and densification processes were investigated by infrared spectroscopy and X-ray powder diffraction (XRD) techniques, and the existence of Al–O–Si linkages was confirmed. To demonstrate an application of the anhydrous sol-gel process, aluminosilicate films were deposited onto graphite surfaces by dip coating and densified at 800°C under nitrogen, and their protective effect was evaluated.     

Studies of the surface wettability and hydrothermal stability of methyl-modified silica films by FT-IR and Raman spectra

Fourier transform infrared (FT-IR) and Raman spectroscopy were employed to study the hydrothermal stability and the influence of surface functional groups on the surface wettability of methyl-modified silica films. The surface free energy parameters of the silica films were determined using the Lifshitz-van der Waals/acid–base approach. The thermal decomposition mechanisms of the CH₃ groups in the methyl-modified silica material are proposed. The results show that with the increase of methyltriethoxysilane (MTES)/tetraethylorthosilicate (TEOS) ratio, the surface free energy and surface wettability of the silica films decrease greatly. This is mainly because of the contribution of the acid–base term; the intensity of Si–CH₃ groups increases at the expense of the intensity of O–H groups in the samples. The surfaces of the methyl-modified silica films exhibited predominantly monopolar electron-donicity. The contact angle on the silica film surface reaches its maximum value when calcination is performed at 350 °C. Thermogravimetric analysis implies that some low molecular weight species, such as H₂, CH₄, and C, are eliminated upon thermal decomposition of the –CH₃ groups. The Si–CH₃ and –CH₃ vibrational bands diminish in intensity as the calcination temperature is increased, disappearing completely when the calcination temperature is increased to 600 °C. When the calcination temperature is increased to 750 °C, the free carbon and CSi₄ species will be formed.     

Immobilization and Characterization of Lactate Dehydrogenase on TEOS Derived Sol-Gel Films

Physical adsorption and physical entrapment techniques have been utilized for the immobilization of lactate dehydrogenase (LDH) on tetraethylorthosilicate (TEOS) derived sol-gel films. The enzyme (LDH) activity has been assayed as a function of time, temperature, pH and pyruvate concentration. The results of photometric measurements used for monitoring the reaction yield a response time of about 1 min, linearity over a concentration range of 0–1.5 × 10^-3 M and detection limit of 5 × 10^-5 M. The TEOS sol-gel films containing LDH have been found to be stable for about 30 days at temperatures 4 to 10°C.     

Preparation of Silica-Silk Fibroin-Polyurethane Composite Films via a Sol-Gel Route

A tetraethoxysilane (TEOS)-derived sol aged for 0 h–6 h at room temperature was mixed with a polyurethane (PU) matrix. A composite of silk fibroin (SF) powders and acrylamide (AAm) was dispersed in the sol-PU mixture and dried isothermally at temperatures between 25°C and 120°C to obtain composite films. Three competitive reactions take place, i.e., those between silica-silica, SF-PU and silica-organic phases, during formation of the composite films. These reactions determine the properties such as morphology and homogeneity of the composite films. IR absorption bands for amide groups (–CONH–), C=O (amide I, 1730 cm^–1) and N–H (amide II, 1530 cm^–1) become larger with decreasing aging time of TEOS-derived sol, or increasing drying temperature. DTA exothermic peak due to the thermal decomposition of SF-AAm composite, on the composite films prepared from the 0 h-aged sol or dried at more than 50°C, shifts toward higher temperature by 44 K or more than 63 K respectively, as compared to the SF-AAm composite. Shorter aging time of TEOS-derived sol and higher drying temperature increased the extent of dispersibility, among SF-AAm composite, PU and silica, to bring a composite film more homogeneous.     

Vibrational spectroscopic studies of vinyltriethoxysilane sol-gel and its coating

Infrared and Raman spectra of vinyltriethoxysilane (VTES), the VTES sol-gel, and the sol-gel coated aluminum have been collected. The assignments of the vibrational modes for the silane, the sol-gel, and the sol-gel films have been made based on the group frequencies and the spectral variation collected at different physical and chemical states of the sol-gel samples. Applying the sol-gels onto the metal grids allowed the drying and the high temperature treatment of the samples for the collection of infrared transmission spectra. From the variation of the sol-gel and the sol-gel coated aluminum IR spectra with temperature, it was noticed that the samples partially decomposed when the temperature was higher than 100 degrees C. Electrochemical experiments have demonstrated that the anticorrosion property of the coated aluminum has significantly increased. The water and the hexadecane contact angle measurements showed that the surface modified metal had a much higher hydrophobic property than the untreated metal.     

Preparation of Thick Films by Electrophoretic Deposition Using Surface Modified Silica Particles Derived from Sol-Gel Method

Thick films were prepared by the electrophoretic sol-gel deposition of organically modified, sub-micron silica particles. The silica particles were modified with 3-aminopropyltriethoxysilane (APS) and vinyltriethoxysilane (VTES). Smooth and crack-free films ca. 15 m thick were obtained when APS modified silica particles were used for the cathodic electrophoretic deposition. Thick films with decreased open spaces among particles were obtained when silica particles modified with VTES were co-deposited with an organic polymer, polyethylene maleate.     

Immobilization of Bromocresol Purple in Inorganic-Organic Sol-Gel Thin Film with Presence of Anionic and Non-ionic Surfactants

Sol-gel materials known as organically modified silicates (ORMOSILs) offer interesting features such as chemical and mechanical stability. In this paper VTES (vinyltriethoxysilane) and TEOS (tetraalkoxysilane) are mixed in 3:1 ratio. Sol-gel solution was prepared by hydrolysis process of precursors by using ethanol as solvent. After a while a pH-sensitive indicator bromocresol purple (BCP) and surfactant were incorporate into the sol-gel mixture. The percentage of sodium dodecyl sulfate (SDS) and polyethylene glycol (PEG) which act as surfactant were varied to observe the effect of improving host material's nanostructure as well as the interaction between BCP and sol-gel matrices. The absorption peak of the BCP dye changed significantly in the presence of surfactant compared to pure VTES: TEOS mixture (control) in the range of 400 to 450 nm. The presence of BCP dye in the sol-gel mixture can be determined via FTIR spectrum with a =C–H stretch in aromatics observed at 3100-3000 cm^-1 which represented the aromatic of the BCP structure. The addition of BCP and surfactant had influenced the FTIR spectra of VTES: TEOS sol-gel materials. Addition of an anionic surfactant to the sol-gel mixtures was found to increase the BCP dye and the sol-gel matrices interaction, thus reducing the dye's tendency to leach. This work shows that sol-gel derived matrices yield dyes with sufficient rigid environment and addition of the surfactant helps to improve the interaction of filler matrices. The anionic SDS shows better leaching resistant compared to non-ionic PEG surfactant. Results of this study offer an attractive possibility to optimize the doped sol gel matrices to be used as sensing material in aqueous condition.     

Small-angle X-ray scattering from wet gels prepared from co-hydrolysis of tetraethoxysilane and vinyltriethoxysilane

Small-angle X-ray scattering was used to study the structure of wet gels prepared from co-hydrolysis of tetraethoxysilane (TEOS) and vinyltriethoxysilane (VTES) in the VTES/(VTES + TEOS) molar ratio ranging from 0 to 1. The wet gels at pH = 6 behave as a mass-fractal structure with characteristic size ξ and fractal dimension D, both increasing with the amount of VTES from ξ = 6.78 nm and D = 2.25 for pure TEOS until an almost homogenous structure with ξ ~ 24.9 nm and D ~ 2.85 is obtained for the wet gel prepared with pure VTES. The mass-fractal structures are built up by small primary clusters of characteristic size between ~0.35 and ~0.85 nm, the size increasing with the quantity of VTES. These small particles of the gels are formed by a restructuring process of a few larger macromolecules in the stable sols (pH = 2) on passing from the acid to the increased-pH step of the process.     

Preparation and characterization of vinyltriethoxysilane grafted ethylene propylene diene terpolymer/linear low density polyethylene (EPDM‐g‐VTES/LLDPE) blends

Graft polymerization of vinyltriethoxysilane (VTES) onto ethylene‐propylene‐diene terpolymer (EPDM) was carried out in toluene using dicumylperoxide (DCP) as initiator. Effects of various parameters (EPDM content, VTES content, reaction time, reaction temperature and initiator concentration) on the grafting efficiency of VTES onto EPDM were investigated. At the optimum grafting efficiency conditions, EPDM‐g‐VTES was developed by melt mixing in a twin screw extruder and then linear (l), statically vulcanized (s) and dynamically vulcanized (d) blends of EPDM‐g‐VTES with linear low‐density polyethylene (LLDPE) with varying percentage compositions were prepared by melt mixing in the twin screw extruder. The grafting of VTES onto EPDM and its crosslinking was confirmed by FT‐IR. The characterization of mechanical properties such as tensile strength, elongation at break, Young's modulus and hardness, differential scanning calorimetry (DSC) analysis and morphology were studied and compared for the EPDM‐g‐VTES/LLDPE blends. The study reveals that the dynamically vulcanized blend improves the mechanical and thermal properties due to the presence of efficient interaction between component polymers when compared with other blends. Copyright © 2005 John Wiley & Sons, Ltd.     

三甲基氯硅烷对纳米多孔二氧化硅薄膜的修饰

以正硅酸乙酯为先驱体,采用溶胶-凝胶法,结合旋转涂胶、超临界干燥工艺在硅片上制备了纳米多孔SiO2薄膜.用三甲基氯硅烷(TMCS)对该SiO2薄膜进行了表面修饰,采用FTIR、TG-DTA、AFM和椭偏仪等方法研究了TMCS修饰前后薄膜的结构、形貌、厚度与介电常数等性能.超临界干燥后的SiO2薄膜含有Si－O－Si与Si－OR结构,呈疏水性.在空气中250 ℃以上热处理后SiO2薄膜因含有Si－OH而呈吸水性. TMCS修饰后的SiO2薄膜在温度不高于450 ℃时可保持其疏水性和多孔结构. SiO2薄膜经TMCS修饰后基本粒子和孔隙尺寸增大,孔隙率提高,介电常数可降低至2.5以下.     

Synthesis and surface properties of self-crosslinking core–shell acrylic copolymer emulsions containing fluorine/silicone in the shell

Stable emulsions of a core–shell acrylic copolymer (non-crosslinkable V0, and crosslinkable V2, V4, V6, and V8, where the numbers indicate the wt% of crosslinking agent based on the total acrylate monomer content) containing butyl acrylate (BA, 45 wt%), glycidyl methacrylate (GMA, 45 wt%), heptadecafluorodecyl methacrylate (PFA, 10 wt%), and various contents of crosslinking agent (vinyltriethoxysilane, VTES) were synthesized using a three-stage seeded emulsion polymerization process with a small amount of surfactant. The average particle size and viscosity of emulsions increased significantly with increasing VTES content. This study examined the effects of the VTES content on the surface/mechanical properties of self-crosslinked copolymer film samples containing a fixed acrylate monomer content to find the optimum VTES content. XPS showed that the film–air surface of the copolymer samples had a higher fluorine/silicone content than the film–dish interface. The tensile strength/modulus, thermal stability, and two Tgs (α and β Tgs) of the film samples increased significantly with increasing VTES content. The contact angle of the film samples increased with increasing VTES content up to approximately 6 wt%, and then decreased slightly. The optimum VTES content was approximately 6 wt% based on the total acrylate monomer content to obtain a high water/oil repellent coating material (V6) with the highest water/methylene iodide-contact angles (118.2°/81.8°) and lowest surface energy (18.4 mN/m).     

Enhancing the organic dye adsorption on porous xerogels

We investigate the adsorption of four different organic dyes (i.e., methyl orange, alizarin red S, brilliant blue FCF, and phenol red) on porous xerogels. To understand the factors affecting the adsorption capacity of the xerogels, we vary the hydrophobicity and the textural properties of the xerogels as well as the solution pH. We control the hydrophobicity by mixing two different precursors (i.e., vinyltriethoxysilane (VTES) and tetraethoxysilane (TEOS)) and the textural properties by using cetyltrimethylammonium bromide (CTAB) as a templating agent. We find that the adsorption capacity is enhanced as the organic/inorganic hybrid xerogel or the templated xerogel is used instead of the purely inorganic or the untemplated xerogel. In all the cases studied, adsorption decreases as the pH is increased due to the electrostatic repulsion between the dyes and the xerogel surface. We find that both the hydrophobic surface and larger pore size/volume are required to enhance the adsorption capacity significantly.     

嫁接Al改性MCM-41介孔分子筛催化合成双酚F

以十六烷基三甲基溴化铵和正硅酸乙酯为原料,合成纯硅MCM-41介孔分子筛。 再利用九水硝酸铝为改性剂来嫁接改性纯硅MCM-41介孔分子筛,NH3-TPD结果表明,嫁接后的AlMCM-41产生了中强酸。 用改性后不同n(Si)/n(Al)的AlMCM-41催化合成双酚F,在n（苯酚）/n（甲醛）=30、反应时间5 h、反应温度90 ℃、m（甲醛）/m（AlMCM-41）=7的反应条件下,在一定范围内,双酚F的产率随Al含量增加而增加,但在n（Si）/n（Al）＜50时,双酚F的产率反而下降,当n（Si）/n（Al）=50时,双酚F的产率最高,为42.28%。