Revisiting Non-Conventional Crystallinity-Induced Effects on Molecular Mobility in Sustainable Diblock Copolymers of Poly(propylene adipate) and Polylactide

This work deals with molecular mobility in renewable block copolymers based on polylactide (PLA) and poly(propylene adipate) (PPAd). In particular, we assess non-trivial effects on the mobility arising from the implementation of crystallization. Differential scanning calorimetry, polarized light microscopy and broadband dielectric spectroscopy were employed in combination for this study. The materials were subjected to various thermal treatments aiming at the manipulation of crystallization, namely, fast and slow cooling, isothermal melt- and cold-crystallization. Subsequently, we evaluated the changes recorded in the overall thermal behavior, semicrystalline morphology and molecular mobility (segmental and local). The molecular dynamics map for neat PPAd is presented here for the first time. Unexpectedly, the glass transition temperature, T_g, in the amorphous state drops upon crystallization by 8–50 K. The drop becomes stronger with the increase in the PPAd fraction. Compared to the amorphous state, crystallization leads to significantly faster segmental dynamics with severely suppressed cooperativity. For the PLA/PPAd copolymers, the effects are systematically stronger in the cold- as compared to the melt-crystallization, whereas the opposite happens for neat PLA. The local β_PLA relaxation of PLA was, interestingly, recorded to almost vanish upon crystallization. This suggests that the corresponding molecular groups (carbonyl) are strongly involved and immobilized within the semicrystalline regions. The overall results suggest the involvement of either spatial nanoconfinement imposed on the mobile chains within the inter-crystal amorphous areas and/or a crystallization-driven effect of nanophase separation. The latter phase separation seems to be at the origins of the significant discrepancy recorded between the calorimetric and dielectric recordings on T_g in the copolymers. Once again, compared to more conventional techniques such as calorimetry, dielectric spectroscopy was proved a powerful and quite sensitive tool in recording such effects as well as in providing indirect indications for the polymer chains’ topology.     

The production and properties of polylactide composites filled with expanded graphite

Composites have been produced by melt-blending biodegradable polylactide (PLA) with commercially available expanded graphite (EG). Using different techniques of addition, the manifold effects of EG on PLA molecular, thermo-mechanical and fire-retardant properties were evaluated. The EG nanofiller provides PLA composites with competitive functional properties. They have a high rigidity, with Young's modulus and storage modulus increasing with EG content. They also have excellent thermal stability while preserving the glass transition and melting temperature of the original PLA matrix. Purification and pre-dispersion of EG nanofiller proved beneficial for preserving PLA molecular weights and led to improved mechanical performance. The presence of dispersed graphene nanolayers in PLA significantly accelerated the polyester crystallization process. The flame retardant properties also displayed improvements with a large decrease in the maximum rate of heat release as recorded by cone calorimetry, whereas the horizontal burning test (UL94 HB) was successfully passed revealing non-dripping and char formation.     

The influence of matrix crystallinity,filler grain size and modification on properties of PLA/calcium carbonate composites

Thermal and mechanical properties of polylactide (PLA) composites with different grades of calcium carbonate, 40 nm and 90 nm nanoparticles, and also with submicron particles, unmodified and modified with calcium stearate or stearic acid, obtained by melt mixing, were compared. Films with amorphous and crystalline matrices were prepared and examined.T_g of PLA in the composites remained unaffected whereas its cold crystallization was enhanced by the fillers and predominantly depended on filler content. Filling decreased thermal stability of the materials but their 5% weight loss temperatures well exceeded 250 °C, evidencing stability in the temperature range of PLA processing. The amorphous nanocomposites with modified nanoparticles exhibited improved drawability and toughness without a significant decrease of tensile strength; nearly two-fold increase of the elongation at break and tensile toughness was achieved at 5 wt% content of the modified nanofiller. Lack of surface modification of the filler, larger grain size with an average of 0.9 μm, and matrix crystallinity had a detrimental effect on the drawability. However, the presence of nanofillers and crystallinity improved tensile modulus of the materials by up to 15% compared to neat amorphous PLA.     

The effect of heat treatment on water sorption in polylactide and polylactide composites via changes in glass‐transition temperature and crystallization kinetics

Water sorption into polylactide (PLA) and polylactide‐montmorillonite (PLLA‐MONT) composites containing 5 wt % of montmorillonite (MONT) under different heat treatment conditions was studied using the quartz crystal microbalance/heat conduction calorimetry (QCM/HCC) technique. Results showed that water sorption in neat polymer films and composite films increased with heat treatment temperature up to 120 °C. Differential scanning calorimetry was used to measure the glass‐transition temperature and isothermal crystallization kinetics of all samples. The mobility of the amorphous domain in all samples increased with heat treatment temperature, indicated by the decrease in glass‐transition temperature. PLA composites crystallized at a much faster rate than neat PLA did because MONT acted as a nucleating agent. Under the same heat treatment condition, water sorption in PLLA‐MONT composites was always higher than that in neat PLA due to the presence of the hydrophilic hydroxyl groups on the surface of MONT particles. © 2011 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2011     

The effect of halloysite nanotubes and N,N'- ethylenebis (stearamide) on the properties of polylactide nanocomposites with amorphous matrix

Amorphous polylactide/halloysite nanotube (PLA/HNT) nanocomposites were prepared and examined. Neat HNT and HNT treated with N,N'- ethylenebis(stearamide) (EBS) were used as nanofillers. The role of HNT and/or EBS content on the cold crystallization of amorphous PLA matrix, HNT dispersion, as well as on the dynamic mechanical and optical properties of the materials was determined.The PLA/HNT-based nanocomposites contained well-distributed nanotubes and occasionally micron-sized aggregates, especially at high loading. HNT, EBS treated HNT and EBS influenced the cold crystallization of PLA, therefore the formation of the disorder α′ and the order α crystallographic forms of PLA.The nanocomposites exhibited increased stiffness and decreased transparency compared to the neat PLA. Due to the reinforcing effect and additional specific features of HNT, the addition of the nanofiller allows tuning of the properties of the nanocomposites with amorphous PLA matrix.     

Thermal,mechanical and electroactive shape memory properties of polyurethane (PU)/poly (lactic acid) (PLA)/CNT nanocomposites

Polymer blend nanocomposites based on thermoplastic polyurethane (PU) elastomer, polylactide (PLA) and surface modified carbon nanotubes were prepared via simple melt mixing process and investigated for its mechanical, dynamic mechanical and electroactive shape memory properties. Chemical and structural characterization of the polymer blend nanocomposites were investigated by Fourier Transform infrared (FT-IR) and wide angle X-ray diffraction (WAXD). Loading of the surface modified carbon nanotube in the PU/PLA polymer blends resulted in the significant improvement on the mechanical properties such as tensile strength, when compared to the pure and pristine CNT loaded polymer blends. Dynamic mechanical analysis showed that the glass transition temperature (T_g) of the PU/PLA blend slightly increases on loading of pristine CNT and this effect is more pronounced on loading surface modified CNTs. Thermal and electrical properties of the polymer blend composites increases significantly on loading pristine or surface modified CNTs. Finally, shape memory studies of the PU/PLA/modified CNT composites exhibit a remarkable recoverability of its shape at lower applied dc voltages, when compared to pure or pristine CNT loaded system.     

Cooperativity length evolution during crystallization of poly(lactic acid)

Effects of stereoregularity and crystallization mode on the amorphous phase dynamics are investigated for poly(lactic acid) PLA. An isothermal crystallization from the melt and a cold crystallization are imposed. For each PLA, the cold crystallization leads to the appearance of a less perfect crystalline phase and to an important rigid amorphous fraction RAF content (35%), although only 10% of RAF is generated after crystallization from the melt. Temperature Modulated Differential Scanning Calorimetry is used to determine the Cooperative Rearranging Regions (CRR) size at the glass transition temperature in the mobile amorphous phase MAP. It is shown that the CRR size in the MAP is not modified by the appearance and the spherulite growth. For the intra-spherulite MAP, a confining effect is evidenced, causing an amorphous phase thickness decrease during crystallization, and inducing a drastic CRR size reduction.     

The effect of halloysite nanotubes and N,N′-ethylenebis (stearamide) on morphology and properties of polylactide nanocomposites with crystalline matrix

Poly(lactide)/halloysite nanotubes (PLA/HNT) nanocomposites with crystalline matrix were obtained by cold crystallization and examined. Neat HNT and HNT treated with N,N′- ethylenebis(stearamide) (EBS) were used as nanofillers. Reference materials, PLA and PLA/EBS blend, prepared in the same way, were also considered. The influence of HNT and/or EBS content on the crystallinity and morphology of PLA matrix, as well as on the dynamic mechanical and optical properties of the materials, was determined.The nanocomposites contained well-distributed HNT, with only occasional agglomerates. HNT, EBS-treated HNT and EBS influenced the morphology of the crystalline PLA matrix and the amounts of the disorder α’ (termed also δ) and order α crystallographic forms of PLA. Crystallinity increased stiffness of the materials compared to their counterparts with the amorphous matrix. Owing to the crystallinity and the presence of the nanofillers, the storage modulus at 20 °C and 60 °C increased by up to 30 and 60%, respectively, compared to neat amorphous PLA. Interestingly, at lower nanofiller content the crystalline nanocomposites with EBS were more transparent than neat crystalline PLA.     

Polylactide compositions. II. Correlation between morphology and main properties of PLA/calcium sulfate composites

Starting from calcium sulfate (gypsum) as fermentation by‐product of lactic acid production process, high performance composites have been produced by melt‐blending polylactide (PLA, L/D isomer ratio of 96:4) and β‐anhydrite II (AII) filler, that is, calcium sulfate hemihydrate previously dehydrated at 500 °C. Characterized by attractive mechanical and thermal properties due to good filler dispersion throughout the polyester matrix, these composites are interesting for potential use as biodegradable rigid packaging. Physical characterization of selected composites filled with 20 and 40 wt % AII has been performed and compared to processed unfilled PLA with similar amorphous structure. State of dispersion of the filler particles and interphase characteristic features have been investigated using light microscopy (LM) and scanning electron microscopy (SEM). Addition of AII did not decrease PLA thermal stability as revealed by thermogravimetry analyses (TGA) and allowed reaching a slight increase of PLA crystallizability during melt crystallization and upon heating from the glassy, amorphous state (DSC). It was found by thermomechanical measurements (DMTA) that the AII filler increased pronouncedly storage modulus (E′) of the composites in comparison with PLA in a broad temperature range. The X‐ray investigations showed stable/unchanged crystallographic structure of AII during processing with molten PLA and in the composite system. The notable thermal and mechanical properties of PLA–AII composites are accounted for by the good filler dispersion throughout the polyester matrix confirmed by morphological studies, system stability, and favorable interactions between components. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 2770–2780, 2007     

Pyrolysis-GC-MS reveals important differences in hydrolytic degradation process of wood flour and rice bran filled polylactide composites

Pyrolysis-GC-MS of polylactide (PLA) biocomposites before and after hydrolytic degradation revealed prominent differences in the hydrolytic degradation process of rice bran and wood flour filled biocomposites. The water uptake and mass loss for polylactide/wood flour composites were similar to that of plain PLA. Pyrolysis-GC-MS, however, showed that on prolonged ageing the hydrolysis of PLA led to increased wood flour concentration in the remaining biocomposite matrices. In contrast, the polylactide/rice bran composites exhibited larger water uptake and higher mass loss. Pyrolysis-GC-MS and FTIR analysis proved that the higher mass loss was caused by migration of rice bran from the composites. The type of natural filler could thus greatly influence the degradation process and/or the stability of the materials in aqueous or humid environments.     

Enhanced Nucleation and Crystallization in PLA/CNT Composites via Disperse Orange 3 with Corresponding Improvement in Nanomechanical Properties

The potential for the material property improvement through the addition of carbon nanotubes (CNTs) in composite materials is often limited due to CNT agglomeration. In this work, Disperse Orange 3 (DO3) was investigated to determine its effectiveness in dispersing CNTs in a poly (lactic acid) (PLA) matrix. First, adsorption studies of DO3 onto CNTs were performed to determine the appropriate amount of DO3 to add so that the CNT surface will be nearly saturated with DO3 while limiting the excess DO3 dissolved in the polymer. The resultant improvements in the mechanical properties were determined via nanoindentation. Highly stable dispersion of CNTs in tetrahydrofuran with DO3 was observed 72 hours after sonication. Scanning electron microscopy confirmed that DO3‐functionalized CNTs were able to separate and disperse well inside of the PLA matrix. Addition of DO3 to the nanocomposite resulted in an increase in the glass transition temperature and crystallinity of the composite due to the more effective dispersion of the nanofiller which serves as a nucleation agent. The CNTs treated with DO3 also increased the elastic modulus and hardness of the composite compared to neat PLA and untreated PLA‐CNT composites. From this study, DO3 was demonstrated to be an effective dispersing agent in the solvent and the PLA matrix which allowed for enhanced crystallization and improved nanomechanical properties in the resultant composite.     

Ultrahigh Molecular mass Polyethylene/ Carbon Nanotube CompositesCrystallization and melting properties

Ultrahigh molecular mass polyethylene (UHMMPE) is filled with carbon nano-tubes (CNTs) by solution in the presence of maleic anhydride grafted styrene-(ethylene-co-butylene)-styrene copolymer (MA-SEBS) as a compatibilizer. The UHMMPE/CNT composites crystallized from melt were prepared at a cooling rate of 20°C min^-1. The melting and crystallization behaviors of UHMMPE/ CNT composites were investigated by differential scanning calorimetry. The results showed that onset melting temperature (T _m) and degree of crystallinity (X _c) of UHMMPE/CNT composites crystallized from solution are higher than those from melt due to the larger crystalline lamellar thickness. The onset crystallization temperature (T _c) of UHMMPE/CNT composites tends to shift to higher temperature region with increasing CNT content in the composites. Tm and Tc of UHMMPE phase in UHMMPE/CNT composites decrease with the addition of MA-SEBS. Moreover, the crystallization rate of UHMMPE phase in UHMMPE/CNT composite is increased due to the introduction of CNTs. MA-SEBS acts as compatilizer, enhances the dispersion of CNTs in the UHMMPE matrix. Thereby, the crystallization rate of UHMMPE phase in UHMMPE/CNT composite is further increased with the addition of MA-SEBS. This revised version was published online in August 2006 with corrections to the Cover Date.     

Poly(cetyl trimethylammonium 4-styrenesulfonate)-wrapped carbon nanotubes filled in polylactide nanocomposites: Fabrication and properties

Poly(cetyl trimethylammonium 4-styrenesulfonate) (PSS-CTA) was synthesized by the ionic exchange reaction of poly(sodium 4-styrenesulfonate) (PSS-Na) with cetyl trimethylammonium bromide (CTAB). It was then used as a surface modifier for carbon nanotubes (CNTs) to improve dispersion in and interfacial adhesion with a polylactide (PLA) matrix to fabricate high performance PLA/CNT nanocomposites via a solution precipitation method. The morphology, electrical conductivity, crystallization and mechanical properties of the PLA nanocomposites were investigated in detail. The results indicate that CNTs wrapped (coated) with a suitable amount of PSS-CTA dispersed in the PLA matrix homogeneously. The electrical conductivity of PLA was enhanced by up to 10 orders of magnitude with the incorporation of 1.0 wt% PSS-CTA-modified CNTs (mCNTs). The crystallization rate of PLA was improved due to the nucleation effect of mCNTs towards the crystallization of PLA, but the crystallization mechanisms and crystal structure of PLA remained unchanged with the incorporation of mCNTs. Both the tensile strength and toughness of PLA were improved by the incorporation of mCNTs, and the fracture behaviour of PLA changed from brittle e to ductile during tensile testing.     

A feasible strategy to constructing hybrid conductive networks in PLA‐based composites modified by CNT‐d‐RGO particles and PEG for mechanical and electrical properties

Carbon nanotubes (CNTs) and reduced graphene oxide (RGO) were successfully assembled by chemical reaction to obtain CNT‐d‐RGO particles. Then, a home‐made dynamic impregnating device was used to prepare hybrid CNT‐d‐RGO/polyethylene glycol (PEG). Next, the different modifiers, including CNTs, GO, CNT‐d‐RGO, PEG, and CNT‐d‐RGO/PEG, were, respectively, added into poly‐(lactic acid) (PLA) matrix via melt‐compounding. The dispersed morphology for these different modifiers within the PLA matrix was confirmed by SEM and TEM observations. Especially, compared with the identical weight ratio of CNT‐d‐RGO, the hybrid CNT‐d‐RGO/PEG within the PLA matrix exhibited an excellent exfoliated and interconnected networks morphology. Moreover, compared with pure PLA, not only the crystallinity of all PLA‐based composites notably improved, but half‐crystallization time was also shortened. Furthermore, despite the addition of different modifiers, the crystal form of PLA‐based composites remained unchanged. Noticeably, compared with those of pure PLA, the tensile stress, strain, and modulus of PLA composite added with CNT‐d‐RGO/PEG increased by 29.4%, 4.1%, and 56.1%, respectively, and the V‐notch impact strength slightly improved. In addition, compared with pure PLA, volume resistivity of the PLA composite added with 1 wt% CNT‐d‐RGO/PEG decreased by 93.1%, and its volume conductivity increased by five orders of magnitude.     

The acquirement of desirable dielectric properties of carbon nanofiber composites based on the controlled crystallization

This study focused on uncovering the relationship among nanofiller, crystallization behavior, and dielectric property of polymer composites. The effects of carbon nanofibers (CNFs) and heat treatment on the crystalline structures and dielectric properties of the semi‐crystalline polymers were analyzed by using high density polyethylene (HDPE) as a matrix, which is a representative of non‐polar polymer and contains only one crystal structure. The experimental results showed that the degree of crystallinity, size distribution of crystallity, and relative amount of different crystal planes in the HDPE matrix were changing due to the addition of CNFs. With the increase of CNF loading, the dielectric constant, dielectric loss and AC conductivity of the HDPE composites were increased, presenting a typical percolation characteristic, and the dependence of the dielectric constant on frequency became more obvious. All kinds of electronic transmission, polarization effect, and relaxation behaviors in CNF/HDPE composite system were deeply analyzed. After heat treatment, the degree of crystallinity of HDPE composites was decreased with the enhanced cooling rate. For the CNF/HDPE composites with nanofiller content slightly higher than the percolation threshold, the significant increase of the dielectric constant and the dramatical reduction of the dielectric loss over a wide frequency range were realized simultaneously through rapid cooling treatment. The research indicated that a general commercial polymer material with excellent dielectric properties, which exhibited a high dielectric constant and a low dielectric loss, can be obtained by a simple technical approach different from traditional fabrication method of threshold composites.     

Microcellular foaming of polylactide and poly(butylene adipate‐co‐terphathalate) blends and their CaCO3 reinforced nanocomposites using supercritical carbon dioxide

Foamed polylactide (PLA), PLA–PBAT (poly (butylene adipate‐co‐terphathalate)) blend and their composites with CaCO₃ were prepared in a batch process using supercritical carbon dioxide (CO₂) at 12 MPa and 45°C. The solubility of CO₂ and its diffusion patterns in different PLA samples was investigated. PLA systems had a relatively high CO₂ solubility related to the carboxyl groups. CO₂ desorption behaviors in PLA systems first followed the Fickian diffusion mechanism in short time and then decreased slowly to a plateau. The addition of both PBAT and CaCO₃ into PLA impeded the desorption of CO₂. In the presence of second phase PBAT, nanoparticles CaCO₃ and dissolved CO₂, the PLA crystallization behavior investigated by DSC technique was greatly changed. As the desorption time increased, the gas induced crystallinity slightly decreased in consequence of less CO₂ content in each system and thus less plasticization effect. The cell morphology of foamed PLA and PLA composites showed interesting microstructure patterns. The prepared pure PLA foam exhibits a typical bimodal structure because of the foaming in both the amorphous and crystalline zones. With PBAT and CaCO₃ into PLA, the composite foam presented significant increase in cell uniformity and cell density. With less CO₂ content in each PLA sample, the cell structure showed interesting variation. Pure PLA foam presented transition from bimodal structure to more uniform cell structure with decreased cell density. In contract, PLA–PBAT foam show unfoamed regions because of none CO₂ left in the separated PBAT phase. Copyright © 2016 John Wiley & Sons, Ltd.     

Replication and surface properties of micro injection molded PLA/MWCNT nanocomposites

Multi-walled carbon nanotube (MWCNT) reinforced polylactide (PLA) nanocomposites were injected molded into a mold with micro needle patterns. In order to alleviate the hesitation effect caused by an increased melt viscositgy of PLA/CNT nanocomposites, the effects of the injection speed and holding pressure on the replication property were investigated. The effects of MWCNTs on the crystallization, thermal behavior, replication properties, replication and surface properties of micro injection molded PLA/CNT nanocomposites were investigated. An analysis of crystallinity and thermal behavior indicated that the MWCNTs promoted the unique α’ to α crystal transition of PLA, leading to an enhancement of surface modulus and hardness, as measured using a nanoindentation technique. The specific interaction between PLA and MWCNTs was characterized using an equilibrium melting point depression technique. Furthermore, the MWCNTs increased the activation energy for thermal degradation of PLA due to the physical barrier effect. The improved replication quality of the microfeatures in the PLA/MWCNT nanocomposites has been achieved by elevating injection speed and holding pressure, which enhances the polymer filling ability within the micro cavity. A replication ratio greater than 96% for the micro injection molded PLA/CNT nanocomposites were achieved at holding pressure of 100 MPa and injection speed of 120 mm/s. This study shows that processing conditions significantly influence the replication and surface properties of micro injection molded PLA/CNT nanocomposites.     

Effects of thermal history on the rigid amorphous phase in poly(phenylene sulfide)

The rigid amorphous phase of semicrystalline poly(phenylene sulfide) (PPS) has been studied as a function of thermal history using scanning calorimetry, dielectric relaxation, density, and small-angle x-ray scattering (SAXS). Based on the new heat of fusion of perfect crystalline PPS, which is 26.7±0.8 cal/gram, the weight fraction of rigid amorphous phase is shown to be nearly twice as large as previously reported [1]. The mass fraction of the rigid amorphous phase ranges from 0.24 to 0.42 and is dependent upon thermal treatment. We have taken the approach of assuming a three-phase model for the morphology of semicrystalline PPS consisting of crystalline lamellae, mobile amorphous, and rigid amorphous components. Using this three-phase model, we determine that the average density of the rigid amorphous fraction is 1.325 g/cc, which is slightly larger than the density of the mobile amorphous phase fraction and was insensitive to thermal history. From the SAXS long period, the layer thicknesses of the mobile amorphous phase, rigid amorphous phase, and crystal lamellae were estimated. Only the lamellar thickness shows a systematic variation with thermal history, increasing with melt or cold crystallization temperature, or with decreasing cooling rate.     

聚乳酸的非等温结晶行为

用差示扫描量热法(DSC)研究聚乳酸(PLA)从熔体及玻璃态为初始条件下的非等温结晶行为,采用Ozawa方程、Mo法、Khanna法和Kissinger法对结晶动力学参数进行计算处理。 实验结果表明,这几种方法均适合处理PLA的非等温结晶过程,而Khanna法提出的结晶速率系数(CRC)能够方便地评价PLA相对结晶速率的大小。 PLA从玻璃态升温结晶比从熔体降温结晶容易得多,升温过程有利于晶核生成,而降温有利于晶体生长。 升温结晶时,升温速率2.0 ℃/min时,结晶焓(ΔH_c)达到最大为27.1 J/g。 从熔体等速降温过程中,随着冷却速率的降低ΔH_c单调增加,冷却速率为0.25 ℃/min时ΔH_c增加到28.3 J/g。 在较低温度下从玻璃态结晶,主要表现为异相成核的二维生长方式。 在较高的温度下从玻璃态升温结晶及从熔体冷却结晶时,以均相成核的三维生长方式结晶为主。 与升温过程相比,冷却不利于晶核的生成,所以导致冷却过程总体ΔH_c偏低,扩散活化能偏大。     

聚乳酸/凹凸棒土纳米复合材料的结构与性能

采用熔融复合方法制备了不同填料质量分数的聚乳酸/纳米凹凸棒土复合材料,纳米凹凸棒土的加入可以显著提高聚乳酸纳米复合材料的拉伸强度和断裂伸长率.扫描电镜结果表明,凹凸棒土粒子在复合材料中实现了均匀分散.DSC曲线在降温过程中出现明显结晶峰,说明纳米凹凸棒土对聚乳酸有一定的成核作用.当纳米凹凸棒填料含量>8%时,在聚合物基体中可形成完善的网络状结构.填料粒子作为体系中的物理缠结点使得复合材料熔体的应力松弛时间延长.红外谱图显示纳米凹凸棒土和聚乳酸分子间存在较强的相互作用.我们推测,纳米凹凸棒土的加入减少了PLA基体层的厚度,使其由三维应力转变为二维应变状态,导致最大切应力可以达到剪切屈服强度,产生剪切滑移形变带,使得呈现出韧性材料性质,有效提高了材料的断裂伸长率.