Chemoselective O-tert-butoxycarbonylation of hydroxy compounds using NaLaTiO4 as a heterogeneous and reusable catalyst

A facile, efficient and chemoselective protocol for O-tert-butoxycarbonylation of various hydroxy compounds has been developed using NaLaTiO₄ (layered perovskite) as a novel catalyst. The catalyst showed remarkable activity and reusability affording high yields of the desired products under mild reaction conditions.     

水汽和空气焙烧制备LaY沸石的SiCl4气相超稳研究

为了考察不同焙烧条件制备的LaY沸石在SiCl₄气相超稳后性能的差异,采用离子交换和氨水沉淀相结合的方法将La离子负载到NaY沸石上,经水蒸汽焙烧或空气焙烧得到不同La负载量的LaYS和LaYB沸石,再经过SiCl₄气相超稳改性得到DLaYS和DLaYB沸石.XRD数据表明水蒸汽焙烧能使沸石发生更为明显的骨架脱铝;不同La负载量的LaY沸石经SiCl₄气相超稳改性都能顺利实现晶胞收缩.XRF数据表明气相超稳和洗涤过程伴随着稀土La的大量流失,DLaYB沸石中的La流失量相对较小.NH₃-TPD和Py-IR数据表明La负载量相同时,DLaYS沸石的总酸量少于DLaYB沸石的总酸量.固定流化床重油催化裂化评价结果显示,与参比催化剂相比,DLaYS催化剂和DLaYB催化剂都具有汽油收率高、柴油收率低,及总轻质油收率高的特点.La负载量相同时,DLaYS催化剂的汽油收率低于DLaYB催化剂.     

MgF2 as a non-conventional catalyst support

This review reports progress in the study of the surface structure of MgF₂ and its use as a support of catalytically active phases. Magnesium fluoride was applied first as a support in catalysis for systems containing individual oxides of transition metals (Mo, V, W, Cu, Cr) and then two different oxide phases (Cu-Cr, Cu-Mn), a metal phase (Ru, Pd) or heteropolyacids. Its use as a support enabled determination of the structure and surface properties of these catalysts. The MgF₂-supported catalysts are characterized by high activity and selectivity in such processes as: hydrodechlorination of chlorofluorocarbons (CFCs), hydrodesulfurization of organic compounds and purification of fuel combustion products from nitrogen oxides. Magnesium fluoride has been also used in MgF₂-doped chromium or aluminum fluoride catalysts for Cl/F exchange on hydrochlorocarbons.     

A one-pot synthesis of 5,5-disubstituted hydantoin derivatives using magnetic Fe3O4 nanoparticles as a reusable heterogeneous catalyst

A facile and rapid method for the one-pot synthesis of 5,5-disubstituted hydantoins in the presence of magnetic Fe₃O₄ nanoparticles has been developed. The multicomponent reactions of carbonyl compounds (aldehydes and ketones), potassium cyanide and ammonium carbonate were carried out under solvent-free conditions to obtain various hydantoin derivatives. The magnetic catalyst could be readily separated by an external magnet from the reaction mixture. This procedure has many advantages, such as the use of a reusable magnetic catalyst, high yields, short reaction times, simplicity and very easiness with implementing the methodology.     

Application of Li2SiO3 as a heterogeneous catalyst in the production of biodiesel from soybean oil

Biodiesel was synthesized from soybean oil by transesterification over Li₂SiO₃ catalyst.The Li₂SiO₃ can be used for biodiesel production directly without further drying or thermal pretreatment,no obvious difference in the FAME conversion（92.4-96.7%） between the air-exposed catalyst（24-72 h） and the fresh one（94.2%）.This leads to important benefits when considering industrial applications of Li₂SiO₃ as a solid catalyst for storing and handling catalyst without taking special actions.     

Ethylene/1-hexene copolymerization with TiCl4/MgCl2/AlCl3 catalyst in the presence of hydrogen

A TiCl₄/AlCl₃/MgCl₂ (Cat-B) catalyst containing 5.2 wt.% Al was prepared by the reaction of TiCl₄ with ethanol adduct of AlCl₃/MgCl₂ mixture. A TiCl₄/MgCl₂ catalyst (Cat-A) without doped AlCl₃ was also prepared by the same method. Ethylene-1-hexene copolymerization catalyzed by Cat-B in the presence of hydrogen showed slightly higher efficiency and higher 1-hexene incorporation than Cat-A. Comonomer incorporation was markedly increased when the cocatalyst AlEt₃ was replaced by Al(i-Bu)₃. Adding Ph₂Si(OMe)₂ as external donor in the catalyst system caused decrease in polymerization activity and 1-hexene incorporation. Each copolymer sample was fractionated into three fractions: n-heptane insoluble fraction (fraction A), n-heptane soluble and n-hexane insoluble fraction (fraction B) and n-hexane soluble fraction (fraction C). In most cases the amount of intermediate fraction (fraction B) was smaller than the other fractions and did not increase as the total 1-hexene content increase, indicating the presence of two classes of copolymer fractions with greatly different comonomer content and clear bimodality of the copolymer composition distribution. Doping AlCl₃ in the catalyst, changing cocatalyst and adding external donor mainly changed the weight ratio of fraction A to fraction C, but exerted little influences on their composition. According to the sequence distribution data of the fractions, doping AlCl₃ in the catalyst resulted in slight decrease of product of reactivity ratios (r₁r₂) in both fraction A and fraction C.     

Ring opening of epoxides with alcohols using Fe(Cp)2BF4 as catalyst

Fe(Cp)₂BF₄ is an efficient catalyst for the alcoholysis of aromatic, aliphatic, and cyclic epoxides giving excellent yields of the corresponding β-alkoxy alcohols under ambient conditions. The methanolysis of styrene oxide using Fe(Cp)₂BF₄ as a catalyst (5 mol %) gave excellent yield of 2-methoxy-2-phenylethanol with complete regio-selectivity. The ring opening of cyclic epoxides gave 77–97% yields of trans-β-methoxy alcohols, in 0.5–6 h. The use of 1,2-epoxyhexane and 1,2-epoxydodecane as substrates gave both regioisomers in excellent yields. The first order rate of reaction with respect to catalyst was observed for the kinetics of ring opening of 1,2-epoxyhexane with methanol.     

Fe（HSO4）3： An efficient,heterogeneous and reusable catalyst for the synthesis of 14-aryl- or alkyl- 14H-dibenzo[a,j]xanthenes

Fe（HSO4）3 has been used as an efficient and recyclable catalyst for the one-pot synthesis of 14-aryl- or alkyl-14Hdibenzo[aj]xanthene derivatives by the reaction of 2-naphtol and aldehydes. Different types of aromatic and aliphatic aldehydes are used in the reaction and in all cases the products were obtained in good to excellent yields.     

Supramolecular aggregation in new crystals with nonlinear optical properties: 2-aminophenol-HClO4, 3-aminophenol-HClO4 and 4-aminophenol-HClO4

Three new hybrid crystals of 2-aminophenol-HClO₄ (2-AP-HClO₄, 1), 3-aminophenol-HClO₄ (3-AP-HClO₄, 2) and 4-aminophenol-HClO₄ (4-AP-HClO₄, 3) were obtained and their crystal structures determined. The 1 crystallises in centrosymmetric space group C2/c of monoclinic system while the other two (2 and 3) crystallise in the non-centro symmetric space group P2₁ and P2₁2₁2₁, respectively. The oppositely charged units of the crystals, i.e. positively charged 2-APH⁺, 3-APH⁺ and 4-APH⁺ and ClO₄⁻, interact via weak N⁺–HO and O–HO hydrogen bonds forming 3D-supramolecular network. Relative to KDP the SHG efficiencies are 0.62 for 2 and 0.33 for 3, measured at 1064 nm using the Kurtz–Perry method.     

An efficient and convenient protocol for the synthesis of quinoxalines and dihydropyrazines via cyclization-oxidation processes using HClO4·SiO2 as a heterogeneous recyclable catalyst

A convenient and straightforward method has been developed for the synthesis of quinoxalines and dihydropyrazines (DHPs) using α-bromo ketones and 1,2-diamines in the presence of silica supported perchloric acid (HClO₄·SiO₂) at room temperature. The quinoxalines and DHPs were presumably formed via cyclization-oxidation. The catalyst works under heterogeneous conditions and can be recycled.     

锂离子电池片状四氧化三钴负极的合成及改性

采用液相沉淀法结合低温固相热解法合成了锂离子电池片状Co3O4负极.通过X射线粉体衍射(XRD)、Brunauer-Emmett-Teller(BET)比表面积分析、扫描电子显微镜(SEM)及恒电流充放电等表征手段,发现该Co3O4为立方相,结晶完整且无杂质,由直径为1.5-3.0μm、厚度约为100-300 nm的不规则片状颗粒组成,比表面积约为30.5 m2·g-1;其比容量高且容量保持率好,在0.1C倍率下,首次放电容量高达1444.5 mAh·g-1,50次循环后充电容量仍大于1100.0 mAh·g-1;但在高倍率(1C)下,50次循环后充电容量保持率仅为75.3%,倍率性能一般.故采用碳纳米管(CNTs)掺杂改性,结果表明:在1C倍率下,70次循环后复合材料充电容量保持率为96.3%;在2C倍率下,50次循环后充电容量保持率仍高达97.0%,倍率性能显著提升.     

MgAl2O4尖晶石对锂离子电池正极材料LiMn2O4的循环性能影响研究

MgAl₂O₄ spinel doping into cathode materials LiMn₂O₄ was used to improve the cyclic performance of the cathode. X-ray analysis results showed, when MgAl₂O₄ precursors were mixed with LiMn₂O₄ and sintered at 770 ℃ for 12 hour, MgAl₂O₄-LiMn₂O₄ mulriple spinel with the same physical characteristics as pure LiMn₂O₄ were synthesized. The electro-chemical performance testing showed, comparing with pure LiMn₂O₄, the first charge-discharge capacity of doping materials somewhat reduced, but the cyclic performance improved. The mechanism for doping material was also discussed.     

LiNi0.8Co0.15Al0.05O2正极材料的FePO4包覆改性

使用液相包覆工艺对LiNi_(0.8)Co_(0.15)Al_(0.05)O_2(NCA)材料进行FePO_4包覆改性,利用FePO_4优异的结构稳定性与热稳定性,对NCA的长期可靠性与安全性能进行改良。重点研究FePO_4包覆对NCA材料的改性效果,以及不同包覆量造成的NCA材料电化学性能差异。表面包覆的FePO_4保护层,能够防止NCA材料与电解液直接接触发生副反应,抑制长期循环过程中过渡金属离子的溶出,保持结构的长期稳定性。当包覆量为1.0%(w/w)时,NCA材料表现出最优的综合性能,充放电循环800次后,容量保持率依然高达95%,25℃下存储100 d后,容量保持率也高于95%,达到了兼顾能量密度、使用寿命及安全性能的理想效果。     

Controlling/living polymerization of MMA with RGO/BiVO4 as photoinitiator

In this study, reduced grapheme oxide (RGO)/BiVO₄ composite was prepared and characterized by FT-IR, XRD, and UV spectrum. Photo-chemically-mediated atom transfer radical polymerization (ATRP) of methyl methacrylate (MMA) was successfully performed at 25°C in N,N-dimethylformamide (DMF) with RGO/BiVO₄ as photoinitiator, FeCl₃·6H₂O/triphenylphosphine (PPh₃) as catalyst, and ethyl 2-bromoisobutyrate as ATRP initiator. MMAs were polymerized in a controlled manner under ultraviolet (UV) light and sunlight conditions. The results show that a first-order kinetics model was obeyed up to higher conversion. The reaction gave well-controlled PMMA with M_n,GPC close to the theoretical value and a narrow MWD (M_w/M_n<1.5). The experiments of light on and off reveal the photoredox cycle between Fe(III) and Fe(II) species. The living character was further verified by the chain extension experiments.     

一维纳米Co_3O_4,Ag/Co_3O_4及CuO/Co_3O_4的合成与电催化性能(英文)

采用水热合成法制备了Co3O4及复合Ag/Co3O4、CuO/Co3O4一维纳米产品。用XRD,FE-SEM和TEM手段对产品进行了表征。采用循环伏安法研究了合成产品修饰的玻碳电极在碱性溶液中对对硝基苯酚的电催化还原性能。与裸玻碳电极相比,1mmol·L-1的对硝基苯酚在用Co3O4、特别是CuO/Co3O4修饰的玻碳电极上还原的峰电流明显增大,用Ag/Co3O4(Ag/Co原子比分别为1∶5和2∶5)修饰的玻碳电极催化还原对硝基苯酚时,尽管还原峰电流增大不是太大,但其峰电位明显降低(分别降低0.265和0.371V)。     

Ag3PO4/Ag2S/g-C3N4复合光催化剂的制备与性能

通过沉积法和离子交换法成功地制备了Ag_3PO_4/Ag_2S/g-C_3N_4复合型光催化剂。利用X射线多晶粉末衍射仪(XRD)、扫描电子显微镜(SEM)、透射电子显微镜(TEM)、X射线光电子能谱(XPS)、N_2吸附-脱附等温线、紫外-可见漫反射光谱、荧光光谱等手段对样品进行了表征。通过降解罗丹明B考察其可见光催化活性及稳定性,研究了硫化钠与磷酸银物质的量的比值(n_(Na_2S)/n_(Ag_3PO_4))、g-C_3N_4添加量对所制备复合光催化材料性能的影响,同时对光催化机理进行了探讨。结果表明,随着n_(Na2S)/n_(Ag3PO4)的增加,所得复合催化材料活性先增加后降低;当n_(Na2S)/n_(Ag_3PO_4)为1.5%、g-C_3N_4与Ag_3PO_4的质量比为3∶7时制备的催化剂ASC1.5的光催化活性最好,在可见光照射下,40 min内可将罗丹明B完全降解,且5次循环使用后仍保持较高的催化活性。和Ag_3PO_4相比,Ag_3PO_4/Ag_2S/g-C_3N_4复合型光催化材料的活性与稳定性都得到明显提高,这主要归因于复合催化剂比表面积和孔结构的增加,载流子分离效率的提高。光催化机理研究表明,空穴(h~+)、超氧阴离子自由基(·O~(2-))和羟基自由基(·OH)都是光催化过程中的主要活性物种。三者作用大小依次为:h~+·O~(2-)·OH。     

可见光响应的Co3(PO4)2/Ag3PO4纳米复合光催化剂的制备及表征

采用简单的化学偏聚法合成出Ag₃PO₄纳米颗粒、磷酸钴（Co₃（PO₄）₂,CoP）纳米片以及它们两者的纳米复合结构（CoP/Ag₃PO₄）,同时还比较了它们的可见光催化活性. 采用场发射扫描电镜（FESEM）、X 射线衍射（XRD）、紫外-可见（UV-Vis）吸收光谱以及光致发光谱等手段对其形貌、结构、光学以及可见光催化性能等进行表征. 结果表明,CoP/Ag₃PO₄复合纳米结构的可见光降解甲基橙（MO）的速率和循环稳定性均明显优于其它两种物质. 这表明CoP应该起着共催化剂的作用,它能够抑制光生电子与空穴之间的复合,并且提供大量高活性的光生空穴. 此外,我们还发现CoP/Ag₃PO₄降解另一种阳离子型染料——罗丹明B（RhB）的能力则远不如纯Ag₃PO₄,这可能是与光催化剂的表面性质发生改变有关,造成更低的RhB吸附能力. 本文提供了一种廉价制备高效可见光催化剂的新方法.     

对BiVO4/BiPO4复合物可见光催化活性提高的研究

采用水热法合成出具有不同V、P物质的量之比的BiVO₄/BiPO₄复合物.n_V/n_P分别为:0.1/9.9、0.5/9.5、1/9、3/7、5/5.采用 XRD、FE-SEM、EDS、拉曼、可见光光度计、漫反射以及电化学等测试手段对BiVO₄/BiPO₄复合物进行表征.在可见光条件下降解亚甲基蓝来评价BiVO₄/BiPO₄复合物的光催化活性.结果显示,当n_V/n_P<3/7的时候,BiVO₄/BiPO₄复合物的光催化活性随着BiVO₄含量的增加而增加,当n_V/n_P=3/7的时候,复合物具有最佳的光催化性能,反应速率常数k为0.005 1 min^-1,是纯BiPO₄的23.2倍.BiVO₄/BiPO₄复合物的光催化机制主要是由于BiVO₄的加入,提高了电子-空穴的分离率,进而提高了光催化活性.     

Preparation of COF2 using CO2 and F2 in the electrochemical cell with PbSnF4 as a solid electrolyte

Tetragonal PbSnF₄ was prepared by precipitation method with Pb(NO₃)₂ and SnF₂ aqueous solutions. The product was characterized using X-ray diffraction (XRD), X-ray fluorescence spectroscopy (XFS), and the other chemical analyses. Tetragonal PbSnF₄ exhibited the highest electric conductivity of 3.2 Sm⁻¹ at 473 K in air as a fluoride ion conductor. We have investigated the possibility of COF₂ formation using CO₂ and F₂ in an electrochemical cell with PbSnF₄ as a solid electrolyte. At same time, we tried to produce an electric power from an electrochemical cell. This CO₂/F₂ electrochemical cell was constructed with a tetragonal PbSnF₄ disk having Au electrodes. The electromotive force was about 0.9 V at room temperature for 0.1 MPa CO₂/(0.01 MPa F₂ + 0.09 MPa Ar). However, the short circuit current density was 0.24 A m⁻², which was quite small. This current density was so small that no fluorocarbon compound was detected after 3 h discharge using FT-IR.     

BiVO4/BiPO4复合物的制备及可见光催化性能

采用水热法合成出具有不同V、P物质的量之比的BiVO₄/BiPO₄复合物.n_V/n_P分别为:0.1/9.9、0.5/9.5、1/9、3/7、5/5.采用 XRD、FE-SEM、EDS、拉曼、可见光光度计、漫反射以及电化学等测试手段对BiVO₄/BiPO₄复合物进行表征.在可见光条件下降解亚甲基蓝来评价BiVO₄/BiPO₄复合物的光催化活性.结果显示,当n_V/n_P<3/7的时候,BiVO₄/BiPO₄复合物的光催化活性随着BiVO₄含量的增加而增加,当n_V/n_P=3/7的时候,复合物具有最佳的光催化性能,反应速率常数k为0.005 1 min^-1,是纯BiPO₄的23.2倍.BiVO₄/BiPO₄复合物的光催化机制主要是由于BiVO₄的加入,提高了电子-空穴的分离率,进而提高了光催化活性.