纳米晶TiO2电极上半菁衍生物光敏染料

合成了具有不同共轭链长度的吡啶盐类及喹啉盐类半菁染料(E)-N-(4-磺酸丁基)-4-[2-(4-N, N-二甲基氨基苯基)乙烯基]吡啶鎓盐(P1)、(E)-N-(4-磺酸丁基)-4-[2-(4-N, N-二甲基氨基苯基)丁二烯基]吡啶鎓盐(P2)、(E)-N-(4-磺酸丁基)-4-[2-(4-N, N-二甲基氨基苯基)乙烯基]喹啉鎓盐(Q1)以及(E)-N-(4-磺酸丁基)-4-[2-(4-N, N-二甲基氨基苯基)丁二烯基]喹啉鎓盐(Q2).研究了它们的光物理性质，并将它们用作TiO2纳米晶电极的光敏化剂引入光电化学电池.与含有乙烯基共轭桥的染料P1和Q1相比，含有丁二烯基共轭桥的染料P2和Q2在甲醇和氯仿中的最大吸收均发生一定程度的红移，而且吸收光谱变宽.这两类染料都能很好地吸附于TiO2电极上.在比较了四个染料的吸收光谱、摩尔消光系数以及在TiO2电极表面的吸附量后，发现Q1具有最好的光电转化性质.     

长链双烷基次膦酸作为共吸附剂修饰TiO_2光阳极

对TiO2/染料/电解质界面进行修饰是提高染料敏化太阳电池(DSC)性能的有效手段,其中引入共吸附剂有机小分子和染料共同吸附在TiO2表面是一种简单有效提高DSC性能的方法.本文合成了长链的双正十二烷基次膦酸(DDdPA)作为染料的共吸附剂应用于染料敏化太阳电池.通过红外光谱(FT-IR)表征DDdPA在TiO2表面的吸附;借助电化学阻抗谱(EIS)及强度调制光电流谱(IMPS)/强度调制光电压谱(IMVS)等技术表征了电子的传输与复合动力学过程.研究发现,DDdPA可以很好地与染料共同吸附在TiO2表面;与二(3,3-二甲基丁基)次膦酸(DINHOP)相比,DDdPA的引入可以更好地抑制TiO2/染料/电解质界面处的电子复合;在优化浓度配比下,DDdPA的引入有效提高了器件的电子寿命,使TiO2导带边负移约30 mV,最终使器件的开路电压提高了47 mV,光电转换效率提升约10%.     

含二级供电基团的三苯胺类光敏染料合成及太阳能电池中的应用

以N,N-二甲基苯胺作为二级给电子单元, 合成两种具有不同长度共轭链的三苯胺类光敏染料XS19和XS22. 研究了它们的光物理与光电化学性质, 并将它们用作TiO₂纳米晶电极的光敏化剂引入太阳电池, 结果表明, N,N-二甲基苯胺的引入能够抑制染料敏化太阳能电池中的电子复合, 提高电池的光电转换效率. XS22表现出更好的光伏性能, 在AM1.5 (100 mW•cm^－2)的光强下, XS22敏化电池的开路电压(V_OC)为685 mV, 短路电流密度(J_SC)为9.6 mA•cm^－2, 填充因子(FF)为0.72, 总光电转换效率为4.7%.     

N3敏化Ho3+离子修饰TiO2纳米晶电极的光电化学性质

研究了Ho3+离子表面修饰对TiO2纳米晶电极光电性能的影响. TiO2表面氧化钬的存在一方面降低了染料和TiO2之间的电子注入速率, 而另一方面它也能够抑制电荷复合. 结果表明, 在TiO2纳米晶薄膜表面修饰一定厚度的Ho3+离子层, 在电极表面就形成了一个势垒, 能够有效抑制电极表面的电荷复合, 从而提高了染料敏化太阳能电池的光电压和光电转化效率. 在93.1 mW·cm-2白光照射下, TiO2/Ho-0.1 和TiO2/Ho-0.2(0.1 和0.2分别是修饰TiO2电极的Ho3+溶液的浓度, 单位是mol·L-1)两个电极的光电转化效率分别达到8.3%和7.6%, 与TiO2电极(7.2%)比较, 分别增大了15%和5%.     

基于铝离子掺杂二氧化钛薄膜的染料敏化太阳能电池的光电性能

采用水热法制备出Al3+掺杂二氧化钛薄膜,通过玻璃棒涂于导电玻璃上,在450°C的温度下烧结并将其用N3染料敏化制成染料敏化太阳能电池(DSSCs).通过X射线光电子能谱(XPS)、X射线衍射(XRD)、扫描电镜(SEM)及DSSCs测试系统对其进行了测试表征,研究了Al3+掺杂对TiO2晶型及染料敏化太阳能电池的光电性能影响.XPS数据显示Al3+成功掺杂到了TiO2晶格内,由于Al3+的存在,对半导体内电子和空穴的捕获及阻止电子/空穴对的复合发挥重要作用.莫特-肖特基曲线显示掺杂Al3+后二氧化钛平带电位发生正移,并导致电子从染料注入到TiO2的驱动力提高.DSSCs系统测试结果表明,Al3+掺杂的TiO2薄膜光电效率达到6.48%,相对于无掺杂的纯二氧化钛薄膜光电效率(5.58%),其光电效率提高了16.1%,短路光电流密度从16.5mA·cm-2提高到18.2mA·cm-2.     

N3敏化Ho~（3＋）离子修饰TiO2纳米晶电极的光电化学性质

研究了Ho3+离子表面修饰对TiO2纳米晶电极光电性能的影响.TiO2表面氧化钬的存在一方而降低了染料和TiO2之间的电子注入速率,而另一方面它也能够抑制电荷复合.结果表明,在TiO2纳米晶薄膜表面修饰一定厚度的HO3+离子层,在电极表面就形成了一个势垒,能够有效抑制电极表面的电荷复合,从而提高了染料敏化太阳能电池的光电压和光电转化效率.在93.1 mW·cm-2白光照射下,TiO2/Ho-0.1和TiO2/Ho-0.2(0.1和0.2分别是修饰TjO2电极的Ho3+液的浓度,单位是mol·L-1)两个电极的光电转化效率分别达到8.3%和7.6%,与TiO2电极(7.2%)比较,分别增大了15%和5%.     

利用强度调制光电流谱研究TiO2薄膜中染料不均匀分布现象

利用强度调制光电流谱(IMPS)研究了不同微结构的TiO2薄膜在不同的浸泡时间条件下的染料分布情况, 分析了染料分布对染料敏化太阳电池光伏性能的影响. 研究结果表明, TiO2薄膜中确实存在染料的不均匀分布现象, 染料不均匀分布对太阳电池的光伏性能有显著的影响.     

Ru(II)染料与聚3-甲基噻吩复合敏化纳米结构TiO_2电极的光电化学研究

利用光电流作用谱、循环伏安等光电化学方法研究了染料RuL2(SCN)2:2TBA(L=2,2'-bipydine-4,4'-dicarboxylicacid)与聚3-甲基噻吩(P3MT)复合敏化电极的光电化学性质.RuL2(SCN)2:2TBA/P3MT复合敏化TiO2纳米晶多孔膜电极比染料RuL2(SCN)2:2TBA敏化TiO2纳米结构电极的光电转换效率大幅度提高.复合敏化电极中存在p-n异质结有效地抑制了电子的反向复合,减少了电子的损失.     

N,N-二苯基取代的芳炔化合物的合成及光伏性能

以简单原料出发,通过Sonogashira偶联反应和三甲基硅基(TMS)的保护与脱保护,合成了一系列N,N-二苯基取代的芳炔化合物SC1～SC5.这类化合物是以N,N-二苯基为电子给体,羧基为电子受体,芳香炔体系为共轭桥的染料.将化合物SC5吸附到TiO2膜上制备成有机染料敏化太阳能电池,在AM 1.5,100 mW/cm2的模拟太阳光下,电池的光电转换效率(IPCE)值最大达到64%,而且在350～580 nm的范围内都可达到50%以上.电池的短路电流密度Jsc=8.0mW/cm2,开路电压Voc=0.75 V,填充因子为FF=0.70,总光电转换效率η=4.2%.     

染料敏化太阳电池中TiO2/染料/电解质界面的修饰

染料敏化太阳电池(DSC)作为新型太阳电池自问世以来受到了广泛关注, 其系统内部的接触界面尤其是TiO₂/染料/电解质界面一直是该领域的研究热点. 光敏染料的吸附以及电子的注入、传输和复合都发生在该界面, 其界面性质对DSC性能具有很大影响. 对染料敏化太阳电池中TiO₂/染料/电解质界面进行修饰可以有效抑制染料聚集和电子复合, 提高电子的注入效率与传输速率; 同时, 对TiO₂导带边的位置及染料吸附等也产生一定的影响, 最终提高电池的光电转换效率和稳定性. 本文主要从不同的修饰途径详细评述了TiO₂/染料/电解质界面修饰方法及机理研究进展,包括TiO₂光阳极的修饰改性、染料溶液中共吸附剂的引入和多种染料共敏化处理以及电解质中不同功能添加剂的应用. 指出了这些修饰方法目前存在的主要问题, 并对未来的发展方向进行了展望.     

Application of Triphenylamine-Based Sensitizers with Two Carboxylic Acid Groups to Dye-Sensitized Solar Cells

Two triphenylamine-based dyes (TPAR3 and TPAR6) containing two carboxylic acid groups with different conjugated lengths were synthesized and characterized with regard to their photophysical and photoelectrochemical properties. Experimental results showed that the λ_max of TPAR6 either in methanol solution or on TiO₂ film was red-shifted and broadened by extending the π-conjugated bridge. However, the performance of TPAR3-based dye-sensitized solar cell (DSC) was superior to that of TPAR6. This reason was due to the serious self-quenching of the electronically excited state in TPAR6 molecule, resulting from its cis-trans isomerization. The effects of addition of guanidinium thiocyanate (GT) in the electrolyte on the performance of DSCs based on TPAR3 were also investigated, revealing a maximum energy conversion efficiency of 4.02% at 0.100 mol·L⁻¹ GT.     

Gundelia tournefortii: Fractionation,Chemical Composition and GLUT4 Translocation Enhancement in Muscle Cell Line

Type 2 diabetes (T2D) is a chronic metabolic disease, which could affect the daily life of patients and increase their risk of developing other diseases. Synthetic anti-diabetic drugs usually show severe side effects. In the last few decades, plant-derived drugs have been intensively studied, particularly because of a rapid development of the instruments used in analytical chemistry. We tested the efficacy of Gundelia tournefortii L. (GT) in increasing the translocation of glucose transporter-4 (GLUT4) to the myocyte plasma membrane (PM), as a main strategy to manage T2D. In this study, GT methanol extract was sub-fractionated into 10 samples using flash chromatography. The toxicity of the fractions on L6 muscle cells, stably expressing GLUTmyc, was evaluated using the MTT assay. The efficacy with which GLUT4 was attached to the L6 PM was evaluated at non-toxic concentrations. Fraction 6 was the most effective, as it stimulated GLUT4 translocation in the absence and presence of insulin, 3.5 and 5.2 times (at 250 μg/mL), respectively. Fraction 1 and 3 showed no significant effects on GLUT4 translocation, while other fractions increased GLUT4 translocation up to 2.0 times. Gas chromatography–mass spectrometry of silylated fractions revealed 98 distinct compounds. Among those compounds, 25 were considered anti-diabetic and glucose disposal agents. These findings suggest that GT methanol sub-fractions exert an anti-diabetic effect by modulating GLUT4 translocation in L6 muscle cells, and indicate the potential of GT extracts as novel therapeutic agents for T2D.     

Syntheses of new model compounds related to an antigenic epitope from Bupleurum falcatum L. and their distributions in various ganglioside-phospholipid monolayers

6-N-[2-(Tetradecyl)hexadecanamido]hexyl beta-D-glucopyranosyluronic acid-(1-->6)-beta-D-galactopyranosyl-(1-->6)-beta-D-galactopyranoside (1) and its clustering compound (2) carrying a tetravalent sugar unit, which are new model compounds related to a major antigenic epitope from antiulcer pectic polysaccharide of Bupleurum falcatum L., were synthesized and the distributions of 1 and 2 in mixed ganglioside (GM1, GD1a or GT1b)/phospholipid (DPPC) monolayers were observed using atomic force microscopy (AFM). AFM images showed that 1 was distributed in the GM1, GD1a and GT1b region of the mixed monolayers, in which 1 was miscible with GD1a. Specific distribution of 1 was observed in the mixed GM1/DPPC monolayer. Compound 2 was miscible with GM1, while 2 formed associations with GD1a and GT1b in the mixed monolayers. The distribution mode of 1 and 2 was different among the mixed ganglioside/DPPC monolayers.     

Heavy Metal Resistances and Chromium Removal of a Novel Cr(VI)-Reducing Pseudomonad Strain Isolated from Circulating Cooling Water of Iron and Steel Plant

Three bacterial isolates, GT2, GT3, and GT7, were isolated from the sludge and water of a circulating cooling system of iron and steel plant by screening on Cr(VI)-containing plates. Three isolates were characterized as the members of the genus Pseudomonas on the basis of phenotypic characteristics and 16S rRNA sequence analysis. All isolates were capable of resisting multiple antibiotics and heavy metals. GT7 was most resistant to Cr(VI), with a minimum inhibitory concentration (MIC) of 6.5 mmol L^?1. GT7 displayed varied rates of Cr(VI) reduction in M2 broth, which was dependent on pH, initial Cr(VI) concentration, and inoculating dose. Total chromium analysis revealed that GT7 could remove a part of chromium from the media, and the maximum rate of chromium removal was up to 40.8 %. The Cr(VI) reductase activity of GT7 was mainly associated with the soluble fraction of cell-free extracts and reached optimum at pH 6.0～8.0. The reductase activity was apparently enhanced by external electron donors and Cu(II), whereas it was seriously inhibited by Hg(II), Cd(II), and Zn(II). The reductase showed a K _m of 74 μmol L^?1 of Cr(VI) and a V _max of 0.86 μmol of Cr(VI) min^?1 mg^?1 of protein. The results suggested that GT7 could be a promising candidate for in situ bioremediation of Cr(VI).     

Isolation and identification of cyclic oligomers of the poly(ethylene terephthalate)–poly(ethylene isophthalate) copolymer

New cyclic oligomers of the copolymer of poly(ethylene terephthalate) (PET) and poly(ethylene isophthalate) (PEI) were isolated and identified. A condensation polymerization was carried out at a high temperature, and the solid‐state polymerization that followed yielded the high molecular weight polymer. The oligomers were extracted from the high molecular weight PET–PEI copolymer and separated with preparative high performance liquid chromatography techniques. Their chemical structures and properties were analyzed and determined by ¹H NMR, differential scanning calorimetry, and mass spectroscopy. The oligomers observed at early retention times were a cyclic dimer and cyclic trimers and consisted of [GT]₃, [GI]₂, [GI]₃, [GT]₂[GI]₁, and [GT]₁[GI]₂. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 881–889, 2003     

Determination of ganglioside composition and structure in human brain hemangioma by chip-based nanoelectrospray ionization tandem mass spectrometry

We report here on a preliminary investigation of ganglioside composition and structure in human hemangioma, a benign tumor in the frontal cortex (HFC) in comparison to normal frontal cortex (NFC) tissue using for the first time advanced mass spectrometric methods based on fully automated chip-nanoelectrospray (nanoESI) high-capacity ion trap (HCT) and collision-induced dissociation (CID). The high ionization efficiency, sensitivity and reproducibility provided by the chip-nanoESI approach allowed for a reliable MS-based ganglioside comparative assay. Unlike NFC, ganglioside mixture extracted from HFC was found dominated by species of short glycan chains exhibiting lower overall sialic acid content. In HFC, only GT1 (d18:1/20:0), and GT3 (d18:1/25:1) polysialylated species were detected. Interestingly, none of these trisialylated forms was detected in NFC, suggesting that such components might selectively be associated with HFC. Unlike the case of previously investigated high malignancy gliosarcoma, in HFC one modified O-Ac-GD2 and one modified O-Ac-GM4 gangliosides were observed. This aspect suggests that these O-acetylated structures could be associated with cerebral tumors having reduced malignancy grade. Fragmentation analysis by CID in MS² mode using as precursors the ions corresponding to GT1 (d18:1/20:0) and GD1 (d18:1/20:0) provided data corroborating for the first time the presence of the common GT1a and GT1b isomers and the incidence of unusual GT1c and GT1d glycoforms in brain hemangioma tumor.      

Matrix isolation FTIR spectroscopic and theoretical study of dimethyl sulfite

The preferred conformations of dimethyl sulfite and their vibrational spectra were studied by matrix-isolation Fourier transform infrared spectroscopy and theoretical methods (density functional theory (DFT) and Moller-Plesset (MP2), with basis sets of different sizes, including the quadruple-zeta, aug-cc-pVQZ basis). Five minima were found at these levels of theory. At the MP2/6-31++G(d,p) and DFT/B3LYP/aug-cc-pVQPZ levels, the GG conformer (where the O-S-O-C dihedral angles are 73.2 and 70.8 degrees ) resulted in the conformational ground state. At the highest level of theory used, the GT conformer (O-S-O-C = +68.5 and -173.2 degrees ) is 0.83 kJ mol(-1) higher in energy than the GG form, while conformer GG' (O-S-O-C = +85.7 and -85.7 degrees ) has a relative energy of 1.18 kJ mol(-1). The remaining two conformers (G'T and TT) are high-energy forms and not experimentally relevant. In consonance with the theoretical predictions, conformer GG was found to be the most stable conformer in the gaseous phase as well as in the low-temperature matrices. Annealing of the argon matrices first promotes the GG'-->GT isomerization, which is followed by conversion of GT into the most stable conformer. There is no evidence of occurrence of GG'-->GG direct conversion in the low-temperature matrices. On the other hand, during deposition of the xenon matrices conformer GG' totally converts to conformer GT. Two observations demonstrated this fact: no evidence of bands corresponding to GG' were observed in xenon matrices and the GG/GT intensity ratio became similar to the GG/(GT + GG') intensity ratio observed in argon matrices. All these results could be explained by taking into account the relative values of the theoretically predicted energy barriers for the different isomerization processes: GG'-->GT, 1.90 kJ mol(-1); GT-->GG, 9.64 kJ mol(-1); and GG'-->GG, 19.46 kJ mol(-1).     

The mechanical properties and structure of poly(m-methylene terephthalate) fibers

A study has been carried out of the differences in mechanical properties of oriented fibers of poly(ethylene terephthalate) (2GT), poly(trimethylene terephthalate) (3GT), and poly(tetramethylene terephthalate) (4GT). The properties studied include the tensile stress–strain behavior, the recovery from strain, shrinkage at 100°C and the glass-transition temperatures. The stress–strain curves of the three materials differ markedly. 2GT shows a monotonic increase in stress with increasing strain up to failure, which occurs at ～20% strain, and the oriented fibers possess a comparatively high initial modulus. 3GT shows a much lower initial modulus and there is an inflection in the stress–strain curve at about 5% strain. The stress–strain curve of 4GT shows a number of distinct features. Although the initial modulus of 4GT is similar to that of 3GT, the stress–strain curve shows a pronounced plateau in the region between 4% and 12% strain. At higher strains the stresses rise rapidly before failure. These features of the stress–strain curves in the three polymers can be related to previous studies where the x-ray diffraction spectrum and the Raman spectrum have been examined for fibers under stress. The ranking of both the recovery and shrinkage behavior of these materials is in the order 3GT > 4GT > 2GT. These results can also be understood in terms of the results of the previous structural studies, and it is concluded that the molecular conformations in both the crystalline and noncrystalline regions play a key role in determining the mechanical behavior.     

Molecular dynamics, density functional and second-order Møller–Plesset theory study of the structure and conformation of acetylcholine in vacuo and in solution

 Molecular mechanics minimizations based on the CVFF force field and molecular dynamics simulation for a time of 2.5 ns were performed to examine the conformational behaviour and the molecular motion of acetylcholine in vacuo and in aqueous solution. Five low-lying conformations, namely the TT, TG, GG, G*G and GT, were obtained from molecular mechanics computations with the GT structure as the absolute minimum. Molecular dynamics trajectories in vacuo and in water show that only four (GT, GG, G*G and TG) and three (TG, TT and GT) conformations are present in the simulation time, respectively. Density functional B3LYP and second-order M?ller–Plesset (MP2) methods were then used to study all the five lowest-lying conformers of acetylcholine neurotransmitter in vacuo and in water by the polarizable continuum model approach. The B3LYP and MP2 computations show that in the gas phase all minima lie in a narrow range of energy with the G*G conformer as the most stable one. The relative minima GG, GT, TG and TT are located at 1.1 (3.3), 1.8 (4.2), 2.1 (4.5) and 4.3 (7.3) kcal/mol above the absolute one at the B3LYP (MP2) level. The preferred conformation in water is the TG. Solvation reduces the relative energy differences between the five minima in both computations. Received: 4 April 2001 / Accepted: 5 July 2001 / Published online: 30 October 2001     

Physical stability of oil-in-water emulsions in the presence of gamma irradiated gum tragacanth

Gum tragacanth (GT) exuding from an Iranian Astragalus species was γ-irradiated at 0, 0.75, 1.5, 3, 5, 7, and 10?kGy and used to stabilize a model oil-in-water emulsion system. Stability and physicochemical properties of emulsion samples were investigated with respect to the effect of irradiation treatment on functional properties of gum tragacanth. Particle size distribution, interfacial tension, zeta potential, steady shear, and oscillatory rheological measurements were used to characterize and evaluate the emulsion samples and obtain more information about the possible stability mechanism. Emulsions were prepared by homogenizing 10% w/w sun flower oil with 90% w/w aqueous gum dispersions and stored quiescently at 25°C for 120 days. The results indicated that using 1.5?kGy irradiated GT was more effective in providing optimum values of apparent viscosity, number mean diameter, electrosteric repulsion, and structure strength for getting the maximum emulsion stability. GT significantly reduced the interfacial tension of the oil and water system, but no significant differences were observed among all irradiation treated and non-irradiated samples. This study revealed that GT acts as a bifunctional emulsifier and irradiation treatment has a great positive influence on its ability to reduce droplets’ collision frequency and stabilize the oil-in-water emulsion.