Investigations on order and width of RZ super Gaussian pulse in pre-, post- and symmetrical-dispersion compensated 10 Gb/s optical communication system using standard and dispersion compensating fibers

We show the effect of varied order and width of super Gaussian pulse at 10 Gb/s in dispersion compensated optical communication system. The optical communication system consists of standard single-mode fiber of 16 ps/nm/km of a certain length, whose dispersion is compensated using pre-, post- and symmetrical-dispersion compensation schemes with proportionate length dispersion compensating fiber of −80 ps/nm/km. Performance of these three compensation schemes is compared at 14 dBm values of Er-doped fiber amplifiers (EDFA) power at 1st, 2nd and 3rd order RZ super Gaussian optical pulse. The pulse width, full width at half maximum (FWHM) is also varied from 5 to 30 ps to highlight the optimum performance. The graphical results obtained show a relationship among the attributes pulse width, order of RZ super Gaussian optical pulse and dispersion compensation scheme implemented. It shows that to decrease BER and timing jitter in the system, smaller width and 3rd order super Gaussian pulse should be used. It is recommended that to decrease dependency of BER and timing jitter in the communication system on the pulse width i.e. FWHM, the symmetrical compensation scheme should be implemented.     

On duty cycle selection of RZ optical pulse to optimize the performance of dispersion compensated 10 Gbps single channel optical communication system using dispersion compensating fibers

We present results for duty cycle selection of optical RZ pulse to optimize the performance in 10 Gbps single channel dispersion compensated optical communication system. The system has link length of 240 km with two spans. Each of the spans consists of 120 km standard single mode fiber (SSMF) of 16 ps/nm/km, whose chromatic dispersion is compensated using pre-, post- and symmetrical-dispersion compensation schemes by 24 km dispersion compensating fiber (DCF) of −80 ps/nm/km. The performance of the three compensation schemes is compared by taking 8, 10, 12 and 14 dBm Er-doped fiber amplifier (EDFA) power levels in the link with a duty cycle range (0.1-0.9) of RZ optical pulse. The graphical results obtained show a relationship among the duty cycle, EDFA power and dispersion compensation scheme which predicts the best performing duty cycle case. To optimize performance of the system, we recommend in general, duty cycle less than 0.3 and EDFA power below 8 dB irrespective of compensation scheme. However, with post compensation duty cycle less than 0.7 and EDFA power below 12 dBm give optimum performance. The results conclude that for the high value of duty cycle, post dispersion compensation scheme should be used.     

Reduction in timing jitter by chirp selection for externally modulated return to zero optical soliton pulse at 10 Gb/s

We investigate the chirp selection of externally modulated RZ soliton pulse at 10 Gb/s for fiber optical communication systems for the reduction in timing jitter. We have chosen single arm Mach-Zehnder amplitude modulator with sin² electrical shaped input-output (P-V) characteristic and its chirp range has been varied in the range of −5 to 5. The timing jitter, Q factor and bit error rate (BER) generated for the chirp range has been studied for various fiber lengths and post compensation has been demonstrated to reduce the timing jitter. The number of fixed output amplifiers after every 60 km span is varied from 2 to 10 and corresponding accumulated ASE noise has been studied to manage timing jitter and BER in permissible range, i.e. 5 ps and 10⁻⁹, respectively. It is observed that when two fiber spans are taken then the compensating fiber length for the system is less than 20 km for each case of the chirp considered. For 10 fiber spans, the compensating fiber length increases in the range 60-90 km depending upon the value of chirp taken. Finally it is shown that the chirp value of external modulator should be set to either 0 or −1 for externally modulated RZ soliton pulse in 10 Gb/s optical communication system which makes the system more insensitive to the timing jitter and the selection of dispersion compensating fiber length.     

Optimizing 10 Gbps optical communication system with duty cycle selection of return to zero pulse

We have investigated the return-to-zero (RZ) pulse duty cycle for single-channel Standard Single mode fiber (SSMF), Non Zero Dispersion shifted fibers (normal NZDSF and anomalous NZDSF fiber) for 10 Gbps optical fiber communication system. We give a comprehensive look on the behavior of variable duty cycle optical RZ pulse indicating that lowest bit error rate for duty cycle 0.8 among the duty cycle values 0.2, 0.4, 0.6 and 0.8 investigated for the case of SSMF. The single repeaterless mode fiber length is increased from existing 55 km at duty cycle 0.2 to fiber length 85 km by keeping duty cycle at 0.8. The result is also emphasized through the 10 dB Q value improvement and corresponding improvement in average eye opening diagram. The normal NZDSF show similar improvement but at greater fiber length, it offers BER 10⁻⁹ at length 110 km with duty cycle 0.2. NZDSF operating length can further be increased to length 160 km by keeping duty cycle 0.8. The corresponding 8 dB Q value improvement and Average eye opening improvement also supports the result through its graphical variation. Thirdly Anomalous NZDSF for same optical communication system showed that 0.2 duty cycle value give operational length of 130 km which could be extended to 160 km if 0.8 duty cycle is kept. The corresponding 8 dB Q value improvement, average eye-opening improvement endorsed the fact in the graphs.     

Timing jitter dependence on data format for ideal dispersion compensated 10 Gbps optical communication systems

Simulations for data formats Return to Zero (RZ), Non-Return to Zero (NRZ), RZ-Soliton, Duobinary and their subcategories have been done with and without ideal dispersion compensation for optical communication systems. The results show that, in general, dispersion compensation improves timing jitter. RZ-Rectangular pulses show the smallest value of jitter without compensation. It has been observed that the RZ-Raised Cosine, and Soliton, give minimum jitter after ideal compensation. It has been reported that the BER performance of optical communication system using Duobinary data format is 10⁻⁸ and 10⁻³⁷ before and after dispersion compensation, respectively. Further the comparative study shows that the timing jitter is the lowest in case of RZ-Soliton (0.0127 ns) after dispersion compensation and 0.0135 ns for RZ-Rectangular data format before dispersion compensation.     

2.50 Gbit/s optical CDMA over FSO communication system

Optical CDMA over FSO communication system is very effective to provide high data rate transmission with very low bit error rate and low amount of multiple access interference. In this paper, we have presented optical CDMA over FSO communication system to the range of 8000 m. The simulative results reveal that the transmission distance is limited mainly by the multi-access interference (MAI) which arises when there are number of users in the system because of the fact that one user data becomes noisy for all other users in the channel.     

Placement of optimized semiconductor optical amplifier in fiber optical communication systems

This paper deals with the placement of semiconductor optical amplifier for 10 Gb/s non-return to zero format in single mode and dispersion-compensated fiber link. We investigated post-, pre- and symmetrical power compensation methods for different positions of the SOA in fiber link. The effect of increase in signal input power for the three power compensation methods is compared in terms of eye diagram, bit error rate, eye closure penalty and output received power. It is found that the post-power compensation method is superior to pre- and symmetrical power compensation methods. Further, the effect of variation in length of the standard single mode fiber and dispersion-compensated fiber for three power compensation configurations has also been observed. The impact of eye closure penalty is observed for large transmission distances for different signal input powers.     

Crosstalk pattern penalty reduction at 2.5 Gb/s in an SOA employing an assist light around gain transparency wavelength

We evaluate the inter-channel crosstalk in a semiconductor optical amplifier when injecting a high optical power continuous wave, as assist light, inside its active region around the gain transparency wavelength. In this work, the crosstalk of signal₁ (1535 nm) modulated at 2.5 Gb/s, has been induced by signal₂ (1560 nm) modulated at 2.5 Gb/s as well and having an optical input power of −7.5 dBm to simulate a multi-channel transmission. By measuring the bit error rate of signal₁, we show that the pattern penalty induced by the cross-gain modulation can be significantly reduced or even in certain conditions suppressed by the assist light.     

Ultra high-speed optical signal processing based on single SOA at 60 Gb/s

The paper shows the design of all-optical logic gates OR, AND, NOT, NOR, XNOR, XOR at ultra high speed by using SOA. The simulations of all logic gates are obtained by XGM and FWM in SOA at 40 Gb/s and 60 Gb/s. The OR, AND, NOR logic between two data sources are obtained using a pump signal, while another logic XNOR using two data. The NOT, XOR obtained using FWM and XGM combined. Thus realization of these logics at 40 Gb/s and 60 Gb/s will lead revolution growth in optical signal processing for high-speed operation.     

10 Gb/s WDM-PON based on FP-LDs injection locked by downlink optical carrier

We propose and demonstrate a 10 Gb/s wavelength division multiplexed passive optical network (WDM-PON) where subcarriers are employed to transmit the downstream data and optical carriers of the downlink subcarrier modulated (SCM) lights are reused to injection lock Fabry-Perot laser diodes (FP-LDs) for uplink transmission. Experiment results show that a very good BER performance can be achieved for both uplink and downlink at 10 Gb/s. The impact of optical carrier to subcarrier ratio and wavelength mismatching is also investigated.     

Optimizing the thulium doped fiber amplifier (TDFA) gain and noise figure for S-band 16 × 10 Gb/s WDM systems

This paper aims to evaluate a comprehensive numerical model based on solving rate equations of a thulium-doped silica-based fiber amplifier. The pump power and thulium-doped fiber (TDF) length for single-pass thulium-doped fiber amplifiers (TDFA) are theoretically optimized to achieve the optimum gain and noise figure (NF) at the center of S-band region. The 1064 nm pump is used to provide both ground-state and excited state absorptions for amplification in the S-band region. The theoretical result is in agreement with the published experimental result.     

Optimisation of 40 Gb/s wavelength converters based on four-wave mixing in a semiconductor optical amplifier

The optimum operating powers and wavelengths for a 40 Gb/s wavelength converter based on four-wave mixing in a semiconductor optical amplifier are inferred from experimental results. From these measurements, some general rules of thumb are derived for this kind of devices. Generally, the optimum signal power should be 10 dB lower than the pump power (−16 dB conversion efficiency) whereas the wavelength separation between the signal and the pump carrier should not be lower than about four times the signal bitrate (1.3 nm for 40 Gb/s RZ signals).     

Impact of extinction ratio of single arm sin LiNbO3 Mach-Zehnder modulator on the performance of 10 and 20 Gb/s NRZ optical communication system

We investigate the impact of extinction ratio of single arm sin² LiNbO₃ Mach-Zehnder (MZ) amplitude modulator on the performance of 10 and 20 Gb/s single-channel optical communication system. For different fiber lengths, the system performance has been analyzed with the increase in the extinction ratio. The effect of variation in dispersion parameter has also been illustrated. The impact of extinction ratio (ζ), dispersion parameter and length of the fiber has been further optimized with minimum bit error rate (BER) at optimal decision threshold (10⁻⁹) for 10 and 20 Gb/s bit rate. It is found that the system gives optimum performance at extinction ratio (ζ) value 20 dB. The increase in the transmission distance from 468 km for 10 Gb/s to 532 km for 20 Gb/s has been reported, and 8 dB improvement in the Q value has been observed as the value of ζ is increased from 10 to 20 dB. At 20 Gb/s, the system gives optimum performance for dispersion parameter value only up to 4 ps/nm km; however, at 10 Gb/s the system can operate for dispersion values up to 14.3 ps/nm km. Further we investigate the self-phase modulation (SPM) effect for the increase in the input power. It is observed that the SPM effect is negligible below 3 dB m input power and it increases at higher power levels.     

10 Gb/s TDM passive optical networks using four wavelengths multiplexed channels

We propose a new architecture for 10 Gb/s upstream traffic in TDM-PON using externally injection-locked Fabry-Perot laser diodes (FP-LDs) in each optical network unit (ONU). Four directly modulated 2.5 Gb/s FP-LDs were injection-locked by continuous wave (CW) carriers distributed from the optical line terminal (OLT). Hence, a total of 10 Gb/s upstream traffic can be achieved. Experimental results show negligible power penalty at a transmission of 25 km standard single mode fiber (SMF) without dispersion compensation. The performance of the injection-locked FP-LD is also studied.     

Apodized chirped fibre Bragg gratings for dispersion compensation in a 10 Gbit/s IM-DD semiconductor laser system

Different fibre Bragg grating dispersion compensation schemes are studied for a directly modulated 1550 nm single-mode semiconductor laser signal through a standard nonlinear fibre link. The laser diode is simulated by its stochastic rate equations, while the nonlinear Schrödinger equation is used to simulate the propagation. The optimum length for dispersion compensation after transmission through 100 km SSM fibre is studied. Pulses with a FWHM of the order of 65 ps with any linewidth-enhancement factor are reconstructed using pre-compensation or post-compensation with an apodized 5.75 cm chirped fibre Bragg grating.     

Boost up of four wave mixing signal in semiconductor optical amplifier for 40 Gb/s optical frequency conversion

The 40 Gb/s optical frequency converter for non-return to zero differential phase shift keying (NRZ-DPSK) signal by using four wave mixing in semiconductor optical amplifier (SOA) have achieved sucessfully. The optimized signal-to-pump ratio for NRZ-DPSK by using optimized SOA structure with enhanced FWM effect is also evaluated. The optimum signal-to-pump ratio is 12 dB and 10 dB with Q factor penalty of 0.685 dB and 0.663 dB. The dependence of four wave mixing efficiency and converted signal power on signal input power is studied and it is evaluated that four wave mixing efficiency decreases with increase in the input power. The impact of pump power, signal-to-pump ratio, and SOA parameters with Q factor penalty for 40 Gb/s has been illustrated. It has shown that converted signal power increases up to the saturation power of semiconductor optical amplifier, then decreases. It is observed that for the optimum pump power, OSNR of converted signal varies little with signal input power.     

Head and bit patterned media optimization at areal densities of 2.5 Tbit/in and beyond

Global optimization of writing head is performed using micromagnetics and surrogate optimization. The shape of the pole tip is optimized for bit patterned, exchange spring recording media. The media characteristics define the effective write field and the threshold values for the head field that acts at islands in the adjacent track. Once the required head field characteristics are defined, the pole tip geometry is optimized in order to achieve a high gradient of the effective write field while keeping the write field at the adjacent track below a given value. We computed the write error rate and the adjacent track erasure for different maximum anisotropy in the multilayer, graded media. The results show a linear trade off between the error rate and the number of passes before erasure. For optimal head media combinations we found a bit error rate of 10⁻⁶ with 10⁸ pass lines before erasure at 2.5 Tbit/in².     

Enhanced performance for 10 Gb/s long reach RSOA based WDM-PON by using power pre-emphasized OFDM signal

An extended reach 10 Gb/s wavelength division multiplexing passive optical networks (WDM-PONs) system based on reflective semiconductor optical amplifier (RSOA) is proposed by using power pre-emphasized orthogonal frequency division multiplexing (OFDM) signal. Experimental results show that the proposed technique can effectively enhance the system performance against the limited bandwidth and chirp induced fading effect from direct modulation of RSOA. The receiver sensitivity is improved by 5 dB at the limit of BER for forward error correction (FEC) code over the 60 km and 85 km fiber transmission without any dispersion compensation module.     

10 and 20 Gb/s all-optical RZ to NRZ modulation format and wavelength converter based on nonlinear optical loop mirror

We present experimental and theoretical results on all-optical 10 and 20 Gb/s RZ to NRZ modulation format and wavelength converter based on a nonlinear optical loop mirror (NOLM). A vector model of converter was developed and the shape of converted pulses was found analytically for particular choice of polarization states. In the experiment, non-zero dispersion shifted fiber with a length 1200 m was used as a nonlinear medium. Pulses from a 10 GHz mode-locked semiconductor laser diode were modulated to form pseudorandom RZ signal and eventually time division multiplexed to 20 Gb/s. RZ pulses were subsequently converted to NRZ signal. The performance of the converter was evaluated experimentally using the data communication analyzer and bit error ratio tester.     

Transmission performance of 20 × 10 Gb/s WDM signals using cascaded optimized SOAs with OOK and DPSK modulation formats

We investigated 20 channels at 10 Gb/s wavelength division multiplexing (WDM) transmission over 1190 km single mode fiber and dispersion compensating fiber using cascaded inline semiconductor optical amplifier at a span of 70 km for RZ-DPSK (return zero differential phase-shift keying) modulation format by using same channel spacing, i.e. 100 GHz. We show for RZ-OOK (return zero on-off keying) format a transmission distance of up to 1050 km with Q factor more than 15 dB, without any power drops. We developed the SOA model for inline amplifier having minimum cross-talks and ASE (amplified spontaneous emission) noise power with sufficient gain. At optimal bias current of 400 mA, a high constant gain of 36.5 dB is obtained up to a saturation power of 21.36 mW. So reduction of cross-talk and distortion is possible by decreasing the bias current at appropriate amplification factor.The DPSK modulation format has less cross-talk as compared to OOK format for nonlinearities and saturation case. The impact of optical power received and Q factor at different distance for both RZ-OOK and RZ-DPSK modulation format has been illustrated. We have shown the optical spectrum and clear Eye diagram at the transmission distance of 1190 km in RZ-DPSK system and 1050 km in RZ-OOK systems.The bit error rate (BER) for all channels observed is less than 10⁻¹⁰ up to gain saturation for both DPSK and OOK systems. Finally, we investigated that the transmission distance decreases with a decrease in channel spacing of up to 20 GHz.