丙酮中除虫脲溶液标准物质研制

采用重量-容量法制备丙酮中除虫脲溶液标准物质。准确称量国家二级标准物质除虫脲溶解到色谱纯丙酮中,通过A级容量瓶定容至500 mL,摇匀后分装到2 mL安瓿瓶内共460瓶,每瓶为1 mL,保持低温迅速封口,配制过程中室温保持在(20±2)℃。采用液相色谱法进行均匀性、稳定性检验和定值结果验证。从样品中随机抽取16瓶进行均匀性检验,经F检验表明,在95%的置信区间范围内该标准物质均匀性良好;采用t检验对标准物质稳定性进行检验,标准物质在12月内稳定性良好。对该标准物质的不确定度进行了评定,研制的丙酮中除虫脲溶液标准物质定值结果为100μg/mL,相对扩展不确定度为2%(k=2)。结果表明,该标准物质均匀性与稳定性良好,量值准确,可用于日常分析检测中的方法评价和仪器校准。     

Rapid assays of clozapine and its metabolites in dried blood spots by liquid chromatography and microextraction by packed sorbent procedure

A novel analytical approach has been developed for the determination of clozapine and its metabolites in dried blood spots on filter paper, using a chromatographic method coupled with a microextraction by packed sorbent procedure. The analytes were separated on a RP-C18 column using a mobile phase composed of 20% methanol, 16% acetonitrile and 64% aqueous phosphate buffer. Coulometric detection was used, setting the guard cell at +0.050 V, the first analytical cell at -0.200 V and the second analytical cell at +0.500 V. Clozapine and its metabolites were extracted from dried blood spots with phosphate buffer and, then, a microextraction by packed sorbent procedure for the sample clean-up was implemented obtaining good extraction yields. The calibration curve was linear over the 2.5-1000 ng mL(-1) blood concentration ranges for all the analytes. The method validation gave satisfactory results in terms of sensitivity, precision, selectivity and accuracy. The analytical method was successfully applied to dried blood spots from several psychiatric patients for therapeutic drug monitoring purpose.     

硼亲和吸附剂的制备及其对苯甲酰脲类农药的萃取性能

以3-丙烯酰胺苯硼酸（APB）为单体,二乙烯基苯（DVB）为交联剂,“原位”聚合制备了聚（3-丙烯酰胺苯硼酸-二乙烯基苯）多孔硼亲和整体材料并作为搅拌饼固相萃取（SCSE-APBDVB）的萃取介质。以5种苯甲酰脲农药为目标化合物,详细考察了萃取过程中解吸溶剂、样品基底中pH值以及离子强度、萃取和解吸时间等实验条件对萃取效率的影响。在此基础上,与高效液相色谱-二极管阵列检测器联用建立了环境水样和果汁样品中苯甲酰脲农药残留的测定方法。在最佳条件下,在水样和果汁样品中,5种目标化合物的检出限（LOD,S/N=3）分别在0.055~0.11 μg/L和0.095~0.31 μg/L之间,所建立的方法具有理想的日内和日间重现性（RSD值均小于9.0%）。在对实际环境水样和果汁样品的测定中,不同加标浓度苯甲酰脲的回收率为75.6%~109%。研究表明,由于所制备吸附剂与目标化合物存在B-N配位作用、氢键和疏水等多种作用力,因此SCSE-APBDVB可对苯甲酰脲农药进行有效萃取,所建立的分析方法具有简便、灵敏和环境友好等特点。     

Influence of solvent effects on retention for a porous polymer sorbent in reversed phase liquid chromatography

Summary The influence of acetonitrile, methanol and isopropanol as retention selectivily modifiers in reversed phase liquid chromatography on a poly(styrene-divinylbenzene) macroporous polymer sorbent (PLRP-S) is evaluated using the solvation parameter model. Retention results from a combination of adsorption and partitioning and is influenced by the equilibrium absorption of organic solvent by the polymer from the mobile phase. The sorption of solutes is dominated by the ease of cavity formation in or on the solvated sorbent, with a small contribution from lone pair-lone pair electron interactions. All polar interactions, such as dipole-type and hydrogenbond formation, are more favorable in the mobile phase and reduce retention. Changes in the uptake of organic solvent from the mobile phase affect kinetic properties of the column such as band broadening and porosity as well as retention. The PLRP-S solvated sorbent is suitable for solid-phase extraction and is more retentive than typical silica-based, bonded phase sorbents for extraction from water. As a surrogate system for estimating solute lipophilicity and biological activity through retention-property correlations it provides a poor fit for hydrogen-bond acid solutes and is too dipolar/polarizable to fit some models.     

Influence of solvent effects on retention in reversed-phase liquid chromatography and solid-phase extraction using a cyanopropylsiloxane-bonded,silica-based sorbent

Summary The solvation parameter model is used to characterize the retention properties of a cyanopropylsiloxane-bonded, silica-based sorbent with methanol, acetonitrile, tetrahydrofuran, and isopropanol in water as mobile phases. The system constants over the composition range 1 to 50% (v/v) organic solvent indicate that retention occurs because of the relative ease of cavity formation in the solvated stationary phase compared to the same process in the predominantly aqueous mobile phase as well as from more favorable stationary phase interactions with solutes containing - and n-electrons. The capacity of the solute for dipole-type interactions is not important whereas all hydrogen-bond-type interactions result in reduced retention. Graphing the system constants as a function of mobile phase composition provides a simple mechanism for interpreting the change in capacity of the chromatographic system for retention in terms of changes in the relative weighting of fundamental intermolecular interactions. A comparison is also made with the retention properties of an octadecylsiloxane-bonded, silica-based sorbent with 30% (v/v) methanol in water as the mobile phase and the extraction characteristics of a porous polymer sorbent with 1% (v/v) methanol, acetonitrile, tetrahydrofuran, and isopropanol in water as the sample processing solvent. Changes in sorbent selectivity due to selective uptake of the processing solvent are much smaller for the cyanopropylsiloxane-bonded sorbent than the results found for a porous polymer sorbent.     

Influence of solvent effects on retention in reversed-phase liquid chromatography and solid-phase extraction using a cyanopropylsiloxane-bonded,silica-based sorbent

Summary The solvation parameter model is used to characterize the retention properties of a cyanopropylsiloxanebonded, silica-based sorbent with methanol, acetonitrile, tetrahydrofuran, and isopropanol in water as mobile phases. The system constants over the composition range 1 to 50 % (v/v) organic solvent indicate that retention occurs because of the relative ease of cavity formation in the solvated stationary phase compared to the same process in the predominantly aqueous mobile phase as well as from more favorable stationary phase interactions with solutes containing π- and n-electrons. The capacity of the solute for dipole-type interactions is not important whereas all hydrogen-bond-type interactions result in reduced retention. Graphing the system constants as a function of mobile phase composition provides a simple mechanism for interpreting the change in capacity of the chromatographic system for retention in terms of changes in the relative weighting of fundamental intermolecular interactions. A comparison is also made with the retention properties of an octadecylsiloxane-bonded, silica-based sorbent with 30 % (v/v) methanol in water as the mobile phase and the extraction characteristics of a porous polymer sorbent with 1 % (v/v) methanol, acetonitrile, tetrahydrofuran, and isopropanol in water as the sample processing solvent. Changes in sorbent selectivity due to selective uptake of the processing solvent are much smaller for the cyanopropylsiloxane-bonded sorbent than the results found for a porous polymer sorbent.     

Development of a microextraction by packed sorbent with gas chromatography‐mass spectrometry method for quantification of nitroexplosives in aqueous and fluidic biological samples

A new method for quantification of 12 nitroaromatic compounds including 2,4,6‐trinitrotoluene, its metabolites and 2,4,6‐trinitrophenyl‐N‐methylnitramine with microextraction by packed sorbent followed by gas chromatography and mass spectrometric detection in environmental and biological samples is developed. The microextraction device employs 4 mg of C₁₈ silica sorbent inserted into a microvolume syringe for sample preparation. Several parameters capable of influencing the microextraction procedure, namely, number of extraction cycles, washing solvent, volume of washing solvent, elution solvent, volume of eluting solvent and pH of matrix, were optimized. The developed method produced satisfactory results with excellent values of coefficient of determination (R² > 0.9804) within the established calibration range. The extraction yields were satisfactory for all analytes (> 89.32%) for aqueous samples and (> 87.45%) for fluidic biological samples. The limits of detection values lie in the range 14–828 pg/mL.     

Solute retention in the stationary phase of a liquid-solid chromatographic system

Summary Utilizing the UNIFAC group model of activity coefficients the retention behaviour of a solute in the stationary phase of a liquid-solid chromatographic system is studied. By comparison of experimentally observed capacity ratios and calculated activity coefficients of solutes in the mobile phase, varying the concentration of a polar moderator, it is shown that the calculated activity coefficients in the stationary phase fit very well the equation formally identical with the Langmuir function. Comparison of activity coefficients in the mobile and the stationary phase proves equivalence between the solvent interaction and the competition theory.     

Theory of swelling of a crosslinked substance in equilibrium with a pure solvent in various phases. Part II: The variation of the pressure

A theory of swelling is presented which describes the equilibrium swelling of a body in a solvent in its various states. The pressure dependence of the pressure-concentration swelling curves is treated for the swelling agent occurring in the liquid, crystalline or vapor phase. The slopes of the pressureconcentration swelling curves are dependent on the differential volume of dilution of the solvent and, additionally, on the volume changes of vaporization, crystallization, and sublimation of the solvent corresponding to the state of the swelling agent. At the melting and boiling pressure of the swelling agent the swelling curves change their slopes with a discontinuity, which is most distinct at the evaporation transition. By measurements of the slopes of the swelling curves at the transition pressure the derivative ₁/w₁ at constant temperature and pressure, which is the change of the chemical potential of the solvent with its weight fraction, is obtained. Thus, a further equation is given to test statistical theories at the transition pressures. Simultaneous variations of the swelling with changes of temperature are also treated.     

The theoretical basis of column chromatography in multicomponent separations. Part 1: Analytical requirements and peak resolution. Development of a high performance column system

The point of our published papers since 1957 is reviewed. The relations between the required value of peak resolution, K₁ (or R), and peak separation, K₃ (eqn 9); K₁ and relative accuracy of a peak height quantitative method, P_h (eqn. 10); K₁ and relative accuracy of a peak area method, P_a, (eqn. 12) at different concentration ratios, ?, are derived. The final result in Table 2 shows a large influence of ? on the required value of K₁. The approximately linear relation between peak width and retention value (eqn. 18) exists not only in GC. but also in HPLC. Plate height values H¹ and H^∞ for a solute with capacity ratio, k′, equal to unity or approaching infinity, respectively, are used to evaluate the column efficiency (eqn. 20). The measuring methods (eqn. 21,22,23) and parameters effecting on H¹ and H^∞ are given for GC packed column (eqn. 24), GC open tubular column (eqn. 25) and HPLC (eqn. 26). In the light of this, columns of high efficiency were developed. Some typical chromatograms for high speed analysis and separation of complex mixtures are given.     

Aqueous solution ofN-methylmorpholineN-oxide as a stationary liquid phase in steam chromatography

The retention of more than 70 voltatile organic compounds of different classes was studied by steam chromatography using aqueous solutions ofN-methylmorpholineN-oxide as the stationary liquid phase (SLP). The effects of temperature and composition of the mobile phase on the retention factors (k) for polar and nonpolar sorbates were elucidated. An unusual order of elution of aliphatic alcohols was noted, namely,tert-butyl alcohol <sec-butyl alcohol < isopentyl alcohol <isobutyl alcohol<isopropyl alcohol <n-pentyl alcohol <n-butyl alcohol <n-propyl alcohol <ethanol <methanol. The retention of cyclohexanol was longer than those of benzyl alcohol andn-hexyl alcohol. Nitrogen-containing compounds were selectively separated on the water-organic SLP studied. For example, the retention of aniline was much longer than those of its derivatives,N,N-dimethylaniline andN,N-diethylaniline, having higher boiling points. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 6, pp. 1077–1084, June, 2000.     

The chromatographic properties of a mixed-bed stationary phase combining reversed-phase and strong anion exchange properties

Summary The feasibility of using columns prepared by mixing together ion exchange and reversed-phase packing materials, for the simultaneous separation of ionised and unionised molecules, has been examined using a range of test solutes. Columns prepared in this way showed chromatographic properties which were intermediate between those of the individual phases. The dual nature of the retention mechanism allowed the retention of ionisable molecules to be adjusted using pH whilst that of uncharged compounds was unaffected. The simultaneous chromatography of model compounds and their glucuronide, sulphate and glycine conjugates, under a variety of conditions, was demonstrated.     

Microextraction by packed sorbent and liquid chromatography–tandem mass spectrometry as a tool for quantification of peptides in plasma samples: determination of sensory neuron‐specific receptors agonist BAM8‐22 and antagonist BAM22‐8 in plasma samples

Microextraction by packed sorbent (MEPS) is a miniaturized, solid‐phase extraction (SPE) technique that works online with gas chromatography (GC) and liquid chromatography (LC). Not only is the automation process with MEPS advantageous, but the much smaller volumes of the samples, solvents and dead space in the system also provide other significant advantages such as the speed and the simplicity of the sample preparation process. In this study MEPS has been evaluated for quantification of sensory neuron‐specific receptors agonist (BAM8‐22). Owing to the instability of BAMs, the focus was on fast extraction and determination of the peptide online using LC‐MS/MS. Sorbents such as C2, C8 and ENV+ (hydroxylated polystyrene–divinylbenzene copolymer) were investigated in the present study. MEPS‐C8 gave the best results compared with C2 and ENV and it was used for the method validation. The calibration curve was obtained within the concentration range of 20.0–3045 nmol/L in plasma. The regression correlation coefficients for plasma samples were ≥0.99 for all runs (n = 6). The between‐batch accuracy and precision for BAM8‐22 ranged from ?13 to ?2.0% and from 4.0 to 14%, respectively. Additionally, the accuracy and precision for BAM22‐8 ranged from ?13 to 7.0% and from 3.0 to 12%, respectively. The present method was used for pharmacokinetic studies for BAMs in plasma samples. Copyright © 2012 John Wiley & Sons, Ltd.     

The development and validation of a solid phase extraction/HPLC method for the determination of aflatoxins in groundnut meal

Summary The efficiency of an analytical method for the determination of aflatoxins in groundnut meal has been statistically examined. The procedure consists of a phenyl bonded phase (PH) clean-up of an acetone: water (8515) extract followed by HPLC quantification. Average recoveries from spiked groundnut meal extracts were calculated to be 101.3% and 101.8%, with limits of detection of 7.4 and 2.62 g/kg for aflatoxins-B1 and-B2 respectively. Higher recoveries of aflatoxin-B1 from naturally contaminated samples were recorded using the proposed procedure than those recorded using the official AOAC (CB) method although the precisions of the two methods were not found to differ at the 5% significance level. Similar recoveries of aflatoxin-B2 were recorded for both methods but the proposed procedure was found to be more precise. The proposed PH-HPLC method was far less time consuming and more economical on solvents than the CB procedure.     

Spectroscopy and the classification of liquid stationary phases in gas-liquid chromatography

Summary A table of data for acidity, basicity, polarity and London potential for stationary phases is given. These provide guidance in choosing a stationary phase for a given task from the 26 substances listed. The indices are calculated from infra-red shifts of 1-chlorobutane and the visible wavelength shifts of l₂ when they are dissolved in the stationary phases, from NMR estimates of acidity and basicity and from relative retention data. They replace the less reliable data of Burns and Hawkes. Methods of determining the indices are suggested that require only a gas chromatograph and can be applied by technicians with no specialized understanding of solution parameters. An attempt to add electron donoracceptor indices to the table was unsuccessful. A further table is given of the slopes of the log plots d(logt)/dC for use in extrapolating from one homologue to another on these stationary phases.     

Statistical evaluation of the validity of a method for characterizing stationary phases for reversed-phase liquid chromatography based on retention of homologous series

Summary The validity of a method for characterizing stationary phases for reversed-phase, liquid chromatography, based on the use of homologous series, has been evaluated. The method is based on a retention model which describes the dependence of the logarithm of the capacity factor on mobile phase composition and the carbon number of specific homologous series. A first-order as well as a second-order version of this model was investigated. The second-order model proved to be a significant improvement on the first-order model, even for smaller mobile-phase ranges. Nevertheless both models showed a significant lack of fit, reflecting the incompleteness of these models. Therefore, it is very questionable whether this method is suitable to describe HPLC-column characteristics like hydrophobicity and hydrophylicity.     

一种内嵌三嗪环酰胺极性基团新型固定相的制备及其在碱性化合物分离中的应用

以γ-氨丙基三乙氧基硅烷为偶联剂,三聚氯氰为反应物,采用固液表面连续反应法,依次与乙二胺、十二酰氯进行亲核取代反应,制备了一种嵌入三嗪环酰胺极性基团的新型反相色谱固定相,并采用元素分析法进行了表征。用制备的固定相装填色谱柱,以商品化C18色谱柱作为参考,对比考察了碱性化合物的分离情况。结果表明,极性三嗪环酰胺基团被成功地键合到硅胶表面,连续制备3次所得固定相的C、N、H含量的最大相对偏差均小于5%,说明制备工艺重现性良好;用制备的固定相装填的色谱柱分离5种苯胺类、4种吡啶类碱性化合物的选择性好,峰形对称。该结果为进一步推进该新型固定相的商品化提供了参考数据。     

Carbon nanoparticles from corn stalk soot and its novel application as stationary phase of hydrophilic interaction chromatography and per aqueous liquid chromatography

Carbon nanoparticles (CNPs) (6–18 nm in size) were prepared by refluxing corn stalk soot in nitric acid. The obtained acid-oxidized CNPs are soluble in water due to the existence of carboxylic and hydroxyl groups. ¹³C NMR measurement shows the CNPs are mainly of sp² and sp³ carbon structure different from CNPs obtained from candle soot and natural gas soot. Furthermore, these CNPs exhibit unique photoluminescence properties. Interestingly, the CNPs might be exploited to immobilize on the surface of porous silica particles as chromatographic stationary phase. The resultant packing material was evaluated by high-performance liquid chromatography, indicating that the new stationary phase could be used in hydrophilic interaction liquid chromatography (HILIC) and per aqueous liquid chromatography (PALC) modes. The separation of five nucleosides, four sulfa compounds and safflower injection was achieved by using the new column in the HILIC and PALC modes, respectively.     

Determination of carbofuran in a nutrient solution by GLC/NPD and HPLC

Summary Two analytical methods using GC/NPD and HPLC to analyse carbofuran in a nutrient solution used in hydroponic culture are described. Both methods show a high recovery, (greater than 90%), and their limits of detection are low.