高效全固化紫外四倍频激光器的研究

用半导体激光器抽运的调Q YLF倍频激光器抽运掺钛蓝宝石激光器，用LBO晶体在腔内产生二次谐波，再聚焦到BBO晶体上产生四次谐波深紫外激光。为了提高谐波转换效率，在腔内分别插入了单片、组合双折射滤光片和聚焦透镜，在平均功率为3.6W，波长为527nm的抽运光下得到410mW，417nm的蓝光。用长焦距的透镜聚焦二次谐波，得到34mW，208nm的紫外脉冲激光。从实验上详细研究了基频光的线宽对二次谐波效率的影响，二次谐波的线宽对四次谐波效率的影响、基频光的波长对四次谐波产生效率的影响。全面地分析了单片和组合大拆射滤光片及抽运功率对钛蓝宝石激光器基频光的脉宽、线宽等参量的影响。     

Performance of gain-switched all-solid-state quasi-continuous-wave tunable Ti:sapphire laser system

We have made a gain-switched all-solid-state quasi-continuous-wave （QCW） tunable Ti：sapphire laser system, which is pumped by a 532 nm intracavity frequency-doubled Nd：YAG laser. Based on the theory of gain-switching and the study on the influencing factors of the output pulse width, an effective method for obtaining high power and narrow pulse width output is proposed. Through deliberately designing the pump source and the resonator of the Ti：sapphire laser, when the repetition rate is 6 kHz and the length of the cavity is 220 mm, at an incident pump power of 22 W, the tunable Ti：sapphire laser from 700 to 950nm can be achieved. It has a maximum average output power of 5.6W at 800nm and the pulse width of 13.2 ns, giving an optical conversion efficiency of 25.5% from the 532 mn pump laser to the Ti：sapphire laser.     

采用飞秒光纤激光同步泵浦的自启动锁模钛宝石激光研究

针对常规连续激光泵浦钛宝石激光振荡器不能自启动锁模的缺点,采用倍频飞秒光纤激光同步泵浦,通过调节振荡器腔长与泵浦腔长匹配,实现了飞秒钛宝石激光的自启动锁模。实验中采用3.4 W的倍频掺镱光纤激光同步泵浦钛宝石激光振荡器,获得了平均功率大于130 mW、重复频率75 MHz、光谱宽度大于47 nm、脉冲宽度17 fs的锁模脉冲输出,不仅能够稳定可靠地实现自启动锁模,解决了常规钛宝石激光振荡器锁模启动的困难,而且还具有同步输出1040,800,520 nm三束飞秒激光的特点,为进一步开展飞秒激光相干合成以及光参量放大等研究提供了优势基础。     

High-average-power kilohertz-repetition-rate sub-100-fs Ti:sapphire amplifier system

We report on a femtosecond Ti:sapphire laser amplifier system that generates pulse energies >5 mJ at a 1-kHz repetition rate. The system consists of regenerative and multipass amplifiers and uses the technique of chirped-pulse amplification. When the system was seeded with 70-fs pulses at 800 nm from a self-mode-locked Ti:sapphire oscillator, amplified pulses of 94-fs duration at a repetition rate of 1 kHz and an average output power of 5.4 W were produced. The amplified pulse-repetition rate is variable from 250 Hz to 3 kHz. Pulse energies of >7.5 mJ were obtained at 500 and 250 Hz.     

采用多通腔望远镜谐振腔结构的10MHz重复频率飞秒钛宝石激光器特性研究

通过在钛宝石激光腔内引入望远镜长腔系统增加腔长,实现了重复频率低到10?MHz的飞秒激光振荡,在5?W的抽运功率下获得了平均输出功率200?mW、单脉冲能量20?nJ的稳定输出. 在此基础上分析了腔内不同色散情况下的输出脉冲光谱和脉宽特性,结果表明在腔内存在一定负色散的情况下,锁模脉宽可接近转换极限,最短脉宽可达56?fs. 而在正色散的情况下,锁模输出的脉宽较宽,并且随着腔内正色散的增多,脉宽可到大于600?fs,锁模光谱也呈马鞍形. 关键词： 钛宝石激光器 飞秒脉冲 低重复频率 望远镜腔     

Generation of 7-fs laser pulse directly from a compact Ti:sapphire laser with chirped mirrors

A compact femtosecond Ti:sapphire laser resonator consisting of three chirped mirrors and one output coupler was designed. By accurately balancing the intra- cavity dispersions between Ti:sapphire crystal, air and chirped mirrors, we directly generated the laser pulse shorter than 7 fs at the average power of 340 mW with 3.1 W pump. The repetition rate of the laser oscillator is 173 MHz at the centre wavelength of 791 nm, and the ultrabroaden spectrum covers from 600 nm to 1000 nm. To the best of our knowledge, this is the simplest laser resonator capable of generating sub-10 fs laser pulse.     

飞秒紫外激光脉冲振荡的实验研究

本文讨论了采用空间光脉冲光谱的啁啾特性和选择聚焦透镜焦距相结合的技术大大提高二次谐波转换效率和产生紫外飞秒光脉冲的实验研究.采用一类相位匹配的BBO晶体,当飞秒钛宝石光脉冲平均功率为560mW时,二次谐波输出功率为352mW,二次谐波转换效率高达63%;采用一类相位匹配的LBO晶体时,获得高光束质量的倍频蓝光输出,输出平均功率为170mW,转换效率大于30%.运用LBO倍频产生的蓝光脉冲和剩余的基频光脉冲进行了三次谐波的振荡研究.三倍频晶体采用BBO,通过优化设计倍频光与基频光之间的空间模匹配及精确时间延迟,得到飞秒紫外光输出,输出功率为2mW,中心波长约为280nm,重复率为100MHz.     

Self-starting mode-locked picosecond Ti：sapphire laser by using of a fast SESAM

A stable continuous wave mode-locked picosecond Ti:sapphire laser by using a fast semiconductor saturable absorber mirror (SESAM) is demonstrated. The laser delivers pulse width of 20 ps at a central wavelength of 813 nm and a repetition rate of 100 MHz. The maximum output power is 1.34 W with pump power of 7 W which corresponds to an optical--optical conversion efficiency of 19.1%.     

MW级峰值功率掺钛蓝宝石激光振荡器

在常规重复频率77 MHz掺钛蓝宝石飞秒激光器的基础上,通过腔内引入Herriott型多通望远镜系统增加总腔长及对腔内色散的深入分析和实验控制,实现了低重复频率、高脉冲能量飞秒激光振荡的稳定运行.在连续功率8.2 W的532 nm激光抽运下,得到了重复频率11 MHz、单脉冲能量达72.73 nJ、对应峰值功率MW量级的结果.相对80 MHz重复频率下6.25 nJ的单脉冲能量及150 kW的峰值功率,其输出能力提高了约一个量级. 关键词： 飞秒激光 掺钛蓝宝石激光器 低重复频率 MW     

Sub-10-fs pulse generation from a blue laser-diode-pumped Ti:sapphire oscillator

Pulses as short as 8.1 fs were generated from a blue laser-diode-pumped Kerr-lens mode-locked Ti:sapphire oscillator, with an average power of 27 m W and a repetition rate of 120.6 MHz. The full width at half-maximum exceeds 146 nm, benefitting from the dispersion management by a combination of a low-dispersion fused silica prism pair and a series of double-chirped mirrors. To the best of our knowledge, this is the first time to generate sub-10-fs pulses from a laser diode directly pumped Ti:sapphire oscillator.     

Design and demonstration of a high-energy booster amplifier for a high-repetition rate petawatt class laser system

We have successfully developed a high-energy, high-repetition rate Ti:sapphire laser system that delivers 33 J before compression at 0.1 Hz. The final booster amplifier is based on a 100 mm diameter Ti:sapphire crystal pumped with 72 J of energy in six beams delivered by three frequency-doubled high-repetition rate Nd:glass lasers. This system is, to the best of our knowledge, the first demonstrated petawatt class laser system running at a high repetition rate.     

A double-pass optical parametric amplifier seeded by a blue-shifted output of a photonic-crystal fiber

A blue-shifted output of a photonic-crystal fiber, providing a frequency upconversion of femtosecond Ti:sapphire laser pulses, is used to seed a double-pass optical parametric oscillator (OPA). The OPA is based on a BBO crystal, pumped by 65-mW 150-fs second-harmonic pulses of a Ti:sapphire laser. Gain factors in excess of 10³ are demonstrated for such an OPA, yielding tunable light pulses within the range of wavelengths from 420 to 650 nm, a peak power up to 250 kW, and a typical pulse width of about 200 fs at a repetition rate of 100 kHz. PACS 42.81.Gs; 42.81.Qb     

Second-harmonic generation from a KBe(2) BO(3)F(2) crystal in the deep ultraviolet

By use of KBe(2)BO(3)F(2) (KBBF) crystal with a size of 10 mmx10 mm x1.2 mm and a special prism-coupling technique (PCT), fourth-harmonic generation of Ti:sapphire laser systems from 200 to 179.4 nm has been achieved. Moreover, with a Ti:sapphire laser with a 50-fs pulse duration and a 1-kHz repetition rate, conversion efficiency as high as 13% from 400 to 200 nm without any surface-loss correction has also been obtained. The data show that with the PCT a KBBF crystal can produce deep-UV coherent light with measurable power output.     

High-contrast, high-intensity laser pulse generation using a nonlinear preamplifier in a Ti:sapphire laser system

We report a high-contrast, high-intensity Ti:sapphire chirped-pulse amplification system that incorporates a nonlinear preamplifier based on optical parametric chirped-pulse amplification (OPCPA). By cooling the Ti:sapphire crystal in the final amplifier down to 77 K, the chirped-pulses are amplified to 2.9 J at a 10 Hz repetition rate without a thermal lensing effect. Pulse compression down to 19 fs duration obtained after amplification indicates a peak power of 80 TW. With the OPCPA, the temporal contrast is significantly improved to better than 7x10(-9) in a few picoseconds interval prior to the main laser pulse.     

100-TW sub-20-fs Ti:sapphire laser system operating at a 10-Hz repetition rate

We developed a compact three-stage Ti:sapphire amplifier laser system that produced peak power in excess of 100 TW for a pulse duration of less than 19 fs and an average power of 19 W at a 10-Hz repetition rate. A final 40-mm-diameter Ti:sapphire amplifier is pumped by a Nd:YAG master-oscillator-power-amplifier system that produces ~7-J output of 532-nm radiation. The spatial beam quality is approximately 2 times diffraction limited for the full amplified compressed output pulse. With f/3 optics, this system should therefore be capable of producing a focused intensity of ~3x10(20) W/cm(2) .     

Tunable, low-repetition-rate, cost-efficient femtosecond Ti:sapphire laser for nonlinear microscopy

We report on a broadly tunable, long-cavity Ti:sapphire laser oscillator being mode-locked in the net negative intracavity dispersion regime by Kerr-lens mode-locking, delivering τ _FWHM<300 fs pulses at 22 MHz repetition rate. The wavelength of the laser can be tuned over a 170 nm wide range between 712 nm and 882 nm. Having a typical pump power of 2.6 W, the maximum pulse peak power is 60 kW. Comparison of the reported laser with a standard, 76 MHz Ti:sapphire oscillator regarding two-photon excitation efficiency in a laser scanning microscope shows that the 22 MHz laser generates the same fluorescence signal at considerably, 1.82 times lower average power, which is expected to result in a reduced photothermal damage probability of biological samples. This fact along with the broad tunability and a low pump power requirement makes this cost-effective laser an ideal light source for nonlinear microscopy.     

12-fs pulses from a continuous-wave-pumped 200-nJ Ti:sapphire amplifier at a variable repetition rate as high as 4 MHz

We demonstrate a novel compact femtosecond Ti:sapphire laser system operating at repetition rates from 10 kHz to 4 MHz. The scheme is based on the combination of a broadband cavity-dumped oscillator and a double-pass Ti:sapphire amplifier pumped by a low-noise cw solid-state laser. Amplified pulses with an extremely smooth spectrum, a duration of only 12 fs, and less than 0.25% rms fluctuation are generated in a beam with M2 < 1.2. A maximum pulse energy of 210 nJ and an average output power of as much as 720 mW are achieved. This output energy is sufficient to generate a stable continuum in a sapphire disk.     

Near-infrared cavity-dumped femtosecond optical parametric oscillator

We demonstrate a high-energy near-infrared cavity-dumped femtosecond optical parametric oscillator (OPO) based on periodically poled lithium niobate. The laser generates 90 nJ pulses at a repetition rate of up to 1 MHz when synchronously pumped by 800 mW output from a femtosecond Ti:sapphire laser. The laser is broadly tunable from 1.0 to 1.5 microm in the signal branch, with a pulse duration of < 60 fs at 1.2 microm. High intracavity power is achieved by running the laser in the regime of positive group-velocity dispersion.     

Sub-6-fs pulses from a SESAM-assisted Kerr-lens modelocked Ti:sapphire laser: at the frontiers of ultrashort pulse generation

Well-characterized pulses in the two-optical-cycle regime are demonstrated using a Kerr-lens modelocked (KLM) Ti:sapphire laser and phase-sensitive diagnostics. The oscillator employs double-chirped mirrors (DCMs) for dispersion compensation, spectral shaping via wavelength-dependent output coupling, and a semiconductor saturable absorber mirror (SESAM) for reliable operation at up to 300 mW output power and with a repetition rate of ~90 MHz.In the discussion of the experimental results we emphasize how spectral shaping can be used most efficiently in the generation of the shortest possible pulse supported by the Ti:sapphire gain bandwidth.     

Sub-two-cycle pulses from a Kerr-lens mode-locked Ti:sapphire laser

Pulses shorter than two optical cycles with bandwidths in excess of 400 nm have been generated from a Kerr-lens mode-locked Ti:sapphire laser with a repetition rate of 90 MHz and an average power of 200 mW. Low-dispersion prisms and double-chirped mirrors provide broadband controlled dispersion and high reflectivity. These pulse durations are to our knowledge the shortest ever generated directly from a laser oscillator.