Highly selective and stable electro-catalytic system with ionic liquids for the reduction of carbon dioxide to carbon monoxide

In this study, the electrochemical reduction of CO₂ was examined using a Ag-modified Cu catalyst cathode in a series of mixed ionic liquids (ILs) in the presence or absence of cobalt chloride (CoCl₂). These results indicate that the Ag-modified Cu electrode in EMIMBF₄ + BMIMNO₃ with CoCl₂ exhibited the excellent synergy for the electrochemical reduction of CO₂ to CO with a stable area specific activity, with continuous production for at least 150 h. In such a system, a CO selectivity of 98% was achieved. According to the obtained results, a possible mechanism was proposed. The synergistic effect between the Ag-modified Cu electrode, serving as the main catalyst, and CoCl₂ and ILs, serving as the co-catalysts, is probably responsible for the highly selective and stable electrocatalytic reduction of CO₂ to CO.     

Properties of HTPB based polyurethane membrane prepared by epoxidation method

Hydroxyl-terminated polybutadiene (HTPB) based polyurethane (PU) was synthesized by solution polymerization. The PU was then cast into membrane. The epoxidation of HTPB based PU membrane by an in situ generated peracid method is discussed. The chemical composition of the epoxidized PU membrane was studied by infrared spectroscopy. The absorption peak at 970 cm⁻¹ for the CC double bond decreased with epoxidation time whereas the absorption peak at 1183 cm⁻¹ for oxirane group increased. The absorption peak at about 1700–1740 cm⁻¹ for the CO group and –OH group at about 3200–3700 cm⁻¹ increased with epoxidation time that indicated the side reaction of epoxidation took place. The oxirane weight content was determined by titration method. The density, tensile strength, elongations, and decomposition temperature of the epoxidized PU membranes were measured. The molecular weight between crosslinking points PU membrane was calculated. Contact angle and protein absorption of fibrinogen and albumin experiments were also determined. It was found that the density and the tensile strength of epoxidized PU membrane increased with increasing epoxidation time whereas the molecular weight between crosslinking points, elongation and the amount of protein adsorption on the epoxidized PU membrane decreased. By using Kaelble’s equation and the contact angle data, the surface tension of epoxidized PU membrane was determined. It was found that the surface tension of epoxidized PU membrane increased whereas the contact angle decreased with epoxidation time. The property changes reduced the permeability of gas through epoxidized PU membrane, but increased the gas selectivity between oxygen and nitrogen. The activation energies (E_p) for gas diffusing through various epoxidized PU membranes were obtained by the Arrhenius law; it is evident that E_p increased with the extent of epoxidation.     

Formation of high-performance 6FDA-2,6-DAT asymmetric composite hollow fiber membranes for CO2/CH4 separation

We report that 6FDA-2,6-DAT polyimide can be used to fabricate hollow fiber membranes with excellent performances for CO₂/CH₄ separation. In order to simplify the hollow fiber fabrication process and verify the feasibility of 6FDA-2,6-DAT hollow fiber membranes for CO₂/CH₄ separation, a new one-polymer and one-solvent spinning system (6FDA-2,6-DAT/N-methyl-pyrrolidone (NMP)) with much simpler processing conditions has been developed and the separation performance of newly developed 6FDA-2,6-DAT hollow fiber membranes has been further studied under the pure and mixed gas systems.Experimental results reveal that 6FDA-2,6-DAT asymmetric composite hollow fiber membranes have a strong tendency to be plasticized by CO₂ and suffer severely physical aging with an initial CO₂ permeance of 300 GPU drifting to 76 GPU at the steady state. However, the 6FDA-2,6-DAT asymmetric composite hollow fibers still present impressive ultimate stabilized performance with a CO₂/CH₄ selectivity of 40 and a CO₂ permeance of 59 GPU under mixed gas tests. These results manifest that 6FDA-2,6-DAT polyimide is one of promising membrane material candidates for CO₂/CH₄ separation application.     

Synthesis of a PEBAX-1074/ZnO nanocomposite membrane with improved CO_2 separation performance

In this investigation, polymeric nanocomposite membranes(PNMs) were prepared via incorporating zinc oxide(ZnO) into poly(ether-block-amide)(PEBAX-1074) polymer matrix with different loadings. The neat membrane and nanocomposite membranes were prepared via solution casting and solution blending methods, respectively. The fabricated membranes were characterized by field emission scanning electron microscopy(FESEM) to survey cross-sectional morphologies and thermal gravimetric analysis(TGA)to study thermal stability. Fourier transform infrared(FT-IR) and X-ray diffraction(XRD) analyses were also employed to identify variations of the chemical bonds and crystal structure of the membranes, respectively. Permeation of pure gases, CO_2, CH_4 and N_2 through the prepared neat and nanocomposite membranes was studied at pressures of 3–18 bar and temperature of 25 °C. The obtained results showed that the fabricated nanocomposite membranes exhibit better separation performance compared to the neat PEBAX membrane in terms of both permeability and selectivity. As an example, at temperature of 25 °C and pressure of 3 bar, CO_2 permeability, ideal CO_2/CH_4 and CO_2/N_2 selectivity values for the neat PEBAX membrane are 110.67 Barrer, 11.09 and 50.08, respectively, while those values are 152.27 Barrer,13.52 and 62.15 for PEBAX/ZnO nanocomposite membrane containing 8 wt% ZnO.     

Thermodynamic evaluation and optimization of the (MgCl2 + CaCl2 + MnCl2 + FeCl2 + CoCl2 + NiCl2) system

A complete critical evaluation of all available phase diagram and thermodynamic data has been performed for all condensed phases of the (MgCl₂ + CaCl₂ + MnCl₂ + FeCl₂ + CoCl₂ + NiCl₂) system, and optimized model parameters have been found. The model parameters obtained for the binary subsystems can be used to predict thermodynamic properties and phase equilibria for the multicomponent system. The Modified Quasichemical Model was used for the molten salt phase, and the (MgCl₂ + MnCl₂ + FeCl₂ + CoCl₂ + NiCl₂) solid solution was modeled using a cationic substitutional model with an ideal entropy and an excess Gibbs free energy expressed as a polynomial in the component mole fractions. This is the first of two articles on the optimization of the (NaCl + KCl + MgCl₂ + CaCl₂ + MnCl₂ + FeCl₂ + CoCl₂ + NiCl₂) system.     

Performance of a mixed-conducting ceramic membrane reactor with high oxygen permeability for methane conversion

A mixed-conducting perovskite-type Ba_0.5Sr_0.5Co_0.8Fe_0.2O_3−δ (BSCFO) ceramic membrane reactor with high oxygen permeability was applied for the activation of methane. The membrane reactor has intrinsic catalytic activities for methane conversion to ethane and ethylene. C₂ selectivity up to 40–70% was achieved, albeit that conversion rate were low, typically 0.5–3.5% at 800–900°C with a 50% helium diluted methane inlet stream at a flow rate of 34 ml/min. Large amount of unreacted molecular oxygen was detected in the eluted gas and the oxygen permeation flux improved only slightly compared with that under non-reactive air/He experiments. The partial oxidation of methane to syngas in a BSCFO membrane reactor was also performed by packing LiLaNiO/γ-Al₂O₃ with 10% Ni loading as the catalyst. At the initial stage, oxygen permeation flux, methane conversion and CO selectivity were closely related with the state of the catalyst. Less than 21 h was needed for the oxygen permeation flux to reach its steady state. 98.5% CH₄ conversion, 93.0% CO selectivity and 10.45 ml/cm² min oxygen permeation flux were achieved under steady state at 850°C. Methane conversion and oxygen permeation flux increased with increasing temperature. No fracture of the membrane reactor was observed during syngas production. However, H₂-TPR investigation demonstrated that the BSCFO was unstable under reducing atmosphere, yet the material was found to have excellent phase reversibility. A membrane reactor made from BSCFO was successfully operated for the POM reaction at 875°C for more than 500 h without failure, with a stable oxygen permeation flux of about 11.5 ml/cm² min.     

Thermodynamic evaluation and optimization of the (NaCl + KCl + MgCl2 + CaCl2 + MnCl2 + FeCl2 + CoCl2 + NiCl2) system

A complete critical evaluation of all available phase diagram and thermodynamic data has been performed for all condensed phases of the (NaCl + KCl + MgCl₂ + CaCl₂ + MnCl₂ + FeCl₂ + CoCl₂ + NiCl₂) system, and optimized model parameters have been found. The (MgCl₂ + CaCl₂ + MnCl₂ + FeCl₂ + CoCl₂ + NiCl₂) subsystem has been critically evaluated in a previous article. The model parameters obtained for the binary subsystems can be used to predict thermodynamic properties and phase equilibria for the multicomponent system. The Modified Quasichemical Model was used for the molten salt phase, and the (MgCl₂ + MnCl₂ + FeCl₂ + CoCl₂ + NiCl₂) solid solution was modeled using a cationic substitutional model with an ideal entropy and an excess Gibbs free energy expressed as a polynomial in the component mole fractions. Finally, the (Na,K)(Mg,Ca,Mn,Fe,Co,Ni)Cl₃ and the (Na,K)₂(Mg,Mn,Fe,Co,Ni)Cl₄ solid solutions were modeled using the Compound Energy Formalism.     

Separation of hydrogen from steam using a SiC-based membrane formed by chemical vapor deposition of triisopropylsilane

A silicon carbide-based membrane was formed in the macropores of an α-alumina support tube by chemical vapor deposition of triisopropylsilane at 700–800°C with a forced cross-flow through the porous wall. The membrane permeated gases except H₂O mainly by the Knudsen diffusion mechanism at permeation temperatures of 50–400°C. The H₂/H₂O selectivity was near or below unity because of the hydrophilic nature of the membrane. After a heat-treatment in Ar at 1000°C for 1 h, however, the membrane formed at a final evacuation pressure of 1 kPa exhibited a H₂/H₂O selectivity of 3–5, for a mixed feed of H₂–H₂O–HBr system, associated in a thermochemical water-splitting process. The H₂ permeance was (5–6)×10⁻⁷ mol m⁻² s⁻¹ Pa⁻¹ at 50–400°C. The membrane maintained the H₂/H₂O selectivity for more than 100 h in the H₂–H₂O–HBr mixture at 400°C.     

C2 and C3 hydrocarbon separations in poly(1,5-naphthalene-2,2′-bis(3,4-phthalic) hexafluoropropane) diimide (6FDA-1,5-NDA) dense membranes

The transport of olefin and paraffin namely ethane, ethylene, propane and propylene in aromatic poly(1,5-naphthalene-2,2′-bis(3,4-phthalic) hexafluoropropane) diimide (6FDA-1,5-NDA) dense membranes was investigated. The gas permeability coefficients were measured at pressures from 2.5 to 16 atm for the C₂ hydrocarbon gases and pressures up to 8.4 atm for C₃ systems at 35 °C. This membrane exhibits permeabilities of 0.15, 0.87, 0.023 and 0.24 Barrer with respect to pure ethane, ethylene, propane and propylene, and shows an ideal selectivity of 5.8 for the separation of ethylene/ethane, 10 for propylene/propane, 7.6 for nitrogen/ethane and 50 for nitrogen/propane. The olefins showed a preferred permeability to paraffins and discussion were drawn to the permeability, diffusivity and solubility coefficients. The activation energies of permeation, diffusion and solution were also reported and the effect of temperature on the permeation properties was discussed for the pure gas permeability data obtained from 30 to 50 °C. The plasticisation effect was also found for propane and propylene, respectively, although it was neither detected in the saturated nor unsaturated C₂ hydrocarbons at pressures up to 16 atm.     

Elevated temperature application of polymer hollow-fiber membranes

Three asymmetric hollow-fiber polymer membrane systems were studied for application in elevated temperature, low feed pressure systems: (1) a single component polyaramide, (2) a single component polyimide, and (3) a composite polyimide on a polyimide/polyetherimide blend support. Permeation driving force was increased for the 2.2 psig feed pressure by sweeping an inert gas along the downstream side of the membrane. Both cocurrent and countercurrent sweep flow patterns were examined with only minimal differences found. The polyaramide membrane was stable in the entire range of temperatures tested (23–220°C). After utilizing a silicone rubber post-treatment, the membrane exhibited a hydrogen permeance of approximately 300 GPU at 175°C with a hydrogen to n-butane selectivity of 700. The polyimide-containing membranes had superior room-temperature properties; however, the thin skins aged at elevated temperatures. This aging effect decreased the permeance of the membranes approximately 40% at 175°C and slightly increased the permselectivity; however, the effects of aging leveled out over 200–250 h at 175°C and the membrane properties became constant. At this level, the polyimide membranes exhibited approximately 400 GPU of hydrogen permeance with a 660 selectivity to n-butane.     

Synthesis,crystal structure,and coordination properties of a helical peptide having β-(3-pyridyl)-l-alanine and l-glutamic acid residues

A novel helical peptide containing β-(3-pyirdyl)-l-alanine (Pal) and l-glutamic acid (Glu) residues has been designed and successfully prepared as a model ligand of metalloenzyme active sites. The helical peptide, Boc-Leu-Aib-Glu-Leu-Leu-Pal-Aib-Leu-OEt (1) (Boc = tert-butoxycarbonyl, Aib = 2-aminoisobutylic acid) yields fine crystals as an acetnitrile solvate. The metal ion binding affinities of 1 were tested for CoCl₂ using UV/vis, CD, Raman, and ¹H NMR spectroscopies. The non-linear fitting calculations have revealed the 1:1 complex for CoCl₂ with the binding constant 3.6 (±0.7) × 10² M⁻¹.     

Effects of temperature and anion species on CO2 permeability and CO2/N2 separation coefficient through ionic liquid membranes

The permeability of carbon dioxide (CO₂) through imidazolium-based ionic liquid membranes was measured by a sweep gas method. Six species of ionic liquids were studied in this work as follows: [emim][BF₄], [bmim][BF₄], [bmim][PF₆], [bmim][Tf₂N], [bmim][OTf], and [bmim][dca]. The ionic liquids were supported with a polyvinylidene fluoride porous membrane. The measurements were performed at T = (303.15 to 343.15) K. The partial pressure difference between feed and permeate sides was 0.121 MPa. The permeability of the CO₂ increases with temperature for the all ionic liquid species. Base on solution diffusion theory, it can be explained that the diffusion coefficient of CO₂ in an ionic liquid affects the temperature dependence more strongly than the solubility coefficient. The greatest permeability was obtained with the [bmim][Tf₂N] membrane. The membrane of [bmim][PF₆] presents the lowest permeability.The separation coefficient between CO₂ and N₂ through the ionic liquid membranes was also investigated at the volume fraction of CO₂ at feed side 0.10. The separation coefficient decreases with the increase of temperature for the all ionic liquid species. The membrane of [emim][BF₄] and [bmim][BF₄] gives the highest separation coefficient at constant temperature. The lowest separation coefficient was obtained from [bmim][Tf₂N] membrane which presents the highest permeability of CO₂.     

Preparation of palladium membranes from the reaction of Pd(C3H3)(C5H5) with H2: wet-impregnated deposition

A new technique to prepare a palladium membrane for high-temperature hydrogen permeation was developed: Pd(C₃H₃)(C₅H₅) an organometallic precursor reacted with hydrogen at room temperature to decompose into Pd crystallites. This reaction together with sintering treatment under hydrogen and nitrogen in sequence resulted in the formation of dense films of pure palladium on the surface of the mesoporous stainless steel (SUS) support. Under H₂ atmosphere the palladium membrane could be sintered at 823 K to form a skin layer inside the support pores. The hydrogen permeance was 5.16×10⁻² cm³ cm⁻² cm Hg⁻¹ s⁻¹ at 723 K. H₂/N₂ selectivity was 1600 at 723 K.     

Separation of carbon dioxide from nitrogen using ion-exchanged faujasite-type zeolite membranes formed on porous support tubes

Faujasite-type zeolite membranes were reproducibly synthesized by hydrothermal reaction on the outer surface of a porous α-alumina support tube of 30 or 200 mm in length. The membrane properties were evaluated by CO₂ separation from an equimolar mixture of CO₂ and N₂ at a permeation temperature of 40°C. CO₂ permeance and CO₂/N₂ selectivity of the NaY-type membranes were in the ranges of 0.4×10⁻⁶–2.5×10⁻⁶ mol m⁻² s⁻¹ Pa⁻¹ and 20–50, respectively. The NaY-type membranes were ion-exchanged with alkali and alkaline earth cations. The LiY-type membrane showed the highest N₂ permeance and the lowest CO₂/N₂ selectivity. The KY-type membrane gave the highest CO₂/N₂ selectivity. The NaY-type membrane was stable against exposure to air at 400°C. NaX-type zeolite membranes, formed by decreasing the ratio of SiO₂/Al₂O₃ in the starting solution, exhibited lower CO₂ permeances and higher CO₂/N₂ selectivities than those of the NaY-type zeolite membranes.     

Partial oxidation of ethane to syngas in an oxygen-permeable membrane reactor

A perovskite-type oxide of Ba_0.5Sr_0.5Co_0.8Fe_0.2O_3−δ (BSCFO) with mixed electronic and oxygen ionic conductivity at high temperatures was used as an oxygen-permeable membrane. A tubular membrane of BSCFO made by extrusion method has been used in the membrane reactor to exclusively transport oxygen for the partial oxidation of ethane (POE) to syngas with catalyst of LiLaNiO/γ-Al₂O₃ at temperatures of 800–900 °C. After only 30 min POE reaction in the membrane reactor, the oxygen permeation flux reached at 8.2 ml cm⁻² min⁻¹. After that, the oxygen permeation flux increased slowly and it took 12 h to reach at 11.0 ml cm⁻² min⁻¹. SEM and EDS analysis showed that Sr and Ba segregations occurred on the used membrane surface exposed to air while Co slightly enriched on the membrane surface exposed to ethane. The oxygen permeation flux increased with increasing of concentration of C₂H₆, which was attributed to increasing of the driving force resulting from the more reducing conditions produced with an increase of concentration of C₂H₆ in the feed gas. The tubular membrane reactor was successfully operated for POE reaction at 875 °C for more than 100 h without failure, with ethane conversion of ∼100%, CO selectivity of >91% and oxygen permeation fluxes of 10–11 ml cm⁻² min⁻¹.     

Preparation and application in oil–water separation of ZrO2/α-Al2O3 MF membrane

The composite tubular membranes were prepared by applying suspensions of zirconia particles to form separation top-layers on two different porous α-alumina supports and heating the coated supports to partly sinter the particles of top-layers. The conditions of synthesizing the ZrO₂/α-Al₂O₃ membranes were investigated systematically. The mean pore diameter of zirconia membrane was about 0.2 μm by gas bubble pressure method, and the pure water flux was about 400 and 1500 l/(m² h bar) for ZrO₂ membrane on symmetric and asymmetric Al₂O₃ support, respectively. Zirconia membrane and three different alumina membranes were applied to separate oil–water emulsion obtained from steelworks to evaluate the permeability and separation characteristics, the ZrO₂/α-Al₂O₃ MF membrane in this work was the preferred membrane.     

Electrochemical deposition of (Mn, Co)-codoped ZnO nanorod arrays without any template

(Mn, Co)-codoped ZnO nanorod arrays were successfully prepared on Cu substrates by electrochemical self-assembly in solution of 0.5 mol/l ZnCl₂–0.01 mol/l MnCl₂–0.01 mol/l CoCl₂–0.1 mol/l KCl–0.05 mol/l tartaric acid at a temperature of 90 °C, and these nanorods were found to be oriented in the c-axis direction with wurtzite structure. Energy dispersive X-ray spectroscopy and x-ray diffraction show that the dopants Mn and Co are incorporated into the wurtzite-structure of ZnO. The concentrations of the dopants, and the orientations and densities of nanorods can easily be well controlled by the current densities of deposition or salt concentrations. Magnetization measurement indicates that the prepared (Mn, Co)-codoped ZnO nanorods with a coercivity of about 91 Oe and a saturation magnetization (M_s) of about 0.23 emu/g. The anisotropic magnetism for the (Mn, Co)-codoped ZnO nanorod arrays prepared in solution of 0.5 mol/l ZnCl₂–0.01 mol/l MnCl₂–0.01 mol/l CoCl₂–0.1 mol/l KCl–0.05 mol/l tartaric acid with current density of 0.5 mA/cm² was also investigated, and the crossover where the magnetic easy axis switches from parallel to perpendicular occurs at a calculated time of about 112 min. The anisotropic magnetism, depending on the rod geometry and density, can be explained in terms of a competition between self-demagnetization and magnetostatic coupling among the nanorods.     

Studies on polypyrrole modified nafion membrane for vanadium redox flow battery

In order to prevent the vanadium crossover and preferential water transfer in all-vanadium redox flow battery (VRFB), three methods – electrolyte soaking, oxidation polymerisation and Electrodeposition, were used to modify Nafion 117 membranes using pyrrole. The surface of the modified membranes was uniform and even, and the membranes were characterised in terms of morphology, membrane area resistance, vanadium permeability and water transfer property. The properties of all the modified membranes were improved greatly. The membranes modified by Electrodeposition showed a best combination of the membrane resistance, vanadium permeability and water transfer property, the experimental results showed that the V(IV) ion permeability of polypyrrole modified Nafion membranes by Electrodeposition at the conditions of 0.025 mA cm⁻² and 0 ^°C for 60 min reduced more than 5 times from 2.87 × 10⁻⁶ cm² min⁻¹ to 5.0 × 10⁻⁷cm² min⁻¹, and the water transfer property decreased more than 3 times from 0.72 ml/72 h cm² to 0.22 ml/72 h cm². All above properties made the modified Nafion membranes more applicative in the VRFB system. This paper also reported other methods for Nafion membrane modification and the influences of the deposition conditions on the properties of the membrane selectivity and water transfer.     

Natural gas permeation in polyimide membranes

Polyimide membranes derived from 6FDA-DAM:DABA and 6FDA-6FpDA:DABA copolymers have been used to separate 50/50 CO₂/CH₄ mixtures and multicomponent synthetic natural gas mixtures at 35 °C and feed pressures up to 55 atm. For 6FDA-DAM:DABA 2:1 membranes the effects of thermal annealing and covalent crosslinking are decoupled with respect to effects on permeabilities and selectivity. Crosslinking at 295 °C with 1,4-butylene glycol and 1,4-cyclohexanedimethanol increases CO₂ permeabilities by factors of 4.1 and 2.4, respectively, at 20 atm feed pressure, without a loss in selectivity, relative to crosslinking at 220 °C. Thermal annealing and crosslinking also reduce CO₂ plasticization effects. Crosslinking of DABA-containing copolymers, therefore, can produce membranes with tunable transport properties that offer significantly higher performance with better plasticization-resistance than that reported in the literature for the commercial polymers Matrimid^® and cellulose acetate for CO₂ removal from natural gas mixtures. Separation of complex mixtures containing CO₂, CH₄, C₂H₆, C₃H₈, and C₄H₁₀ or toluene results in a significant decrease of the CO₂ permeability, but only a moderate decrease in the CO₂/CH₄ selectivity.