Preparation of monodisperse carbon nanospheres for electrochemical capacitors

The efficiently hydrothermal route using sucrose without any catalysts is employed to prepare the uniform carbon spheres. The monodisperse 100–150 nm carbon spheres are obtained with the activation treatment in molten KOH. The carbon spheres are characterized by transmission electron microscope, X-ray diffraction, N₂ adsorption, Raman spectroscopy and electrochemical techniques. The relationships of specific capacitance and surface properties of carbon spheres are investigated. A single electrode of carbon nanosphere materials performs excellent specific capacitance (328 F g⁻¹), area capacitance (19.2 μF cm⁻²) and volumetric capacitance (383 F cm⁻³).     

Factors affecting membrane fouling reduction by surface modification and backpulsing

Several factors affecting microfiltration membrane fouling and cleaning, including backpulsing, crossflushing, backwashing, particle size, membrane surface chemistry, and ionic strength, were investigated with suspensions of latex beads. Approximately two-fold permeate volume enhancements over 1 h of filtration were obtained by using water or gas backpulsing, and 50% enhancement was obtained with crossflushing, for filtration of 1.0 μm diameter carboxylate modified latex (CML) particles using unmodified polypropylene (PP) membranes of 0.3 μm nominal pore diameter. When 0.2 μm diameter CML particles or mixtures of 1.0 and 0.2 μm CML particles were used, however, the average flux decreased 60% compared with using 1.0 μm CML particles for experiments with or without backpulsing.PP membranes were rendered hydrophilic with neutral or positively on negatively charged surfaces by grafting monomers of poly(ethylene glycol 200) monomethacrylate (PEG200MA), dimethyl aminoethyl methacrylate (DMAEMA), or acrylic acid (AA), respectively, to the base PP membranes. Filtration experiments show that fouling is not strongly dependent on membrane surface chemistry for filtration of 1.0 μm CML particles without backpulsing. With backpulsing, however, a 10% increase and a 20% decrease of permeate volumes collected in 1 h were observed when the CML particles and the membranes had like charges and opposite charges, respectively, compared to the permeate collected with the unmodified membrane. Using the PP membranes modified with AA, permeate volumes with backpulsing decreased 30 and 40% when NaCl concentrations of 0.01 and 0.1 M, respectively, were added to the feed. However, the permeate volumes did not vary significantly with changing ionic strength for filtration without backpulsing.     

Proton conductive thin films prepared by plasma polymerization

Proton conductive membranes were prepared as thin films of about 10 μm thickness by an ion beam assisted plasma polymerization process. Argon ions were generated in a high frequency plasma and accelerated towards a PTFE target where CF fragments were released as a consequence of the ion impact. Various sulfur components (SO₂, CF₃SO₃H or ClSO₃H) were added to achieve proton conductivity by the formation of sulfonic acid groups. The CF fragments combined with the sulfur components to form a coherent thin film on a substrate. Mass spectrometric investigations revealed, however, that sulfur oxygen compounds were extremely delicate towards reduction to sulfur carbon compounds like CS₂ or SCF₂. The best membrane conductivities (>10⁻⁴ S/cm) and highest ion exchange capacities (0.15 mmol/g) were achieved with chlorosulfonic acid involved in the plasma polymerization process. Ultra-thin layers of these of these plasma polymers (ca. 300 nm) were subsequently deposited onto Nafion^® membranes in order to suppress methanol permeation for a potential application in a direct methanol fuel cell (DMFC). The ratio of proton conductivity and methanol diffusion coefficient was employed for an assessment of the transport characteristics of the coated membrane. Diffusion coefficients were determined in a flow cell coupled to a mass spectrometer. The plasma polymer coating decreased both the methanol permeation and the proton conductivity. With a proton conductive plasma polymer coating the decrease of methanol diffusion could outweigh the loss of proton conductivity. Plasma coating offers a way to suppress methanol crossover in DMFCs and to maintaining the proton conductivity.     

A high performance nano-structure conductive coating on a Crofer22APU alloy fabricated by a novel spinel powder reduction coating technique

A nano-structure conductive coating was fabricated on a Crofer22APU alloy interconnect by an original coating strategy using Mn_0.9Y_0.1Co₂O₄ (MYC) novel spinel nanocrystalline powder. A unique treatment method by which the spinel powder was reduced was used to prepare the green coating. The resulting coating was about 12 μm in thickness, and was composed of MYC nanocrystalline with an average particle size of about 100 nm. The coating was well adhered with the substrate alloy. Less than 4 mΩ cm² of the area specific resistance (ASR) was obtained, and no obvious degradation was observed for a coated alloy (whose coating thickness was about 30 μm) after operated at 800 °C for 538 h under seven thermal cyclings. The coated alloy exhibited excellently electrical performance and long-term stability compared with the uncoated one. The exploration of the novel spinel powder reduction coating technique for alloy interconnect to obtain cheap coatings with excellent microstructure and performance showed a promising prospect for the practical application of solid oxide fuel cells (SOFCs).     

Impedance spectroscopy and conductometric biosensing for probing catalase reaction with cyanide as ligand and inhibitor

In this work, a new biosensor was prepared through immobilization of bovine liver catalase in a photoreticulated poly (vinyl alcohol) membrane at the surface of a conductometric transducer. This biosensor was used to study the kinetics of catalase–H₂0₂ reaction and its inhibition by cyanide. Immobilized catalase exhibited a Michaelis–Menten behaviour at low H₂0₂ concentrations (< 100 mM) with apparent constant K_M^app = 84 ± 3 mM and maximal initial velocity V_M^app = 13.4 μS min^? 1. Inhibition by cyanide was found to be non-competitive and inhibition binding constant K_i was 13.9 ± 0.3 μM. The decrease of the biosensor response by increasing cyanide concentration was linear up to 50 μM, with a cyanide detection limit of 6 μM. In parallel, electrochemical characteristics of the catalase/PVA biomembrane and its interaction with cyanide were studied by cyclic voltammetry and impedance spectroscopy. Addition of the biomembrane onto the gold electrodes induced a significant increase of the interfacial polarization resistance R_P. On the contrary, cyanide binding resulted in a decrease of Rp proportional to KCN concentration in the 4 to 50 μM range. Inhibition coefficient I₅₀ calculated by this powerful label-free and substrate-free technique (24.3 μM) was in good agreement with that determined from the substrate-dependent conductometric biosensor (24.9 μM).     

Spectral study on the inclusion complex of cryptophane-E and CHCl3

Cryptophane-E was synthesized from vanillin by a three-step method, and its absorption and fluorescence spectroscopic properties were determined. Two absorption bands at about 245–260 and 280–290 nm were observed for cryptophane-E and the fluorescence emission maxima were at 320–330 nm depending on the solvent used. The interaction of cryptophane-E with CHCl₃ was studied in detail by absorption and fluorescence spectroscopies. The results showed that cryptophane-E and CHCl₃ can easily form a stable 1:1 host–guest inclusion complex. Their binding constant (K) was determined by Benesi–Hildebrand equation and the nonlinear least squares fit method. The binding constant is largest in ethyl acetate, followed by dioxane and with acetonitrile as the smallest. In addition, the effect of guest volume on the host–guest inclusion complex was investigated. Guest molecules including CH₂Cl₂ and CCl₄ were unable to form inclusion complex with cryptophane-E because of sizes mismatching with the host cavity.     

Amélioration de la tenue à la corrosion atmosphérique de matériaux utilisés en connectique (nickel doré). Traitements de surface par implantations d'ions

Improvement of the atmospheric corrosion resistance of materials used in connectics. Surface treatments by ion implantation. Tests of corrosion of a material, constituted of brass covered with an electrochemical nickel coating (thickness ≈ 5 μm) and with a gold coating (thickness ≈ 0.4 μm or ≈ 1 μm), used in electrical contact applications, have been carried out in humid synthetic air with low contents of NO₂ (0.2 vpm), SO₂ (0.2 vpm) and Cl₂ (0.01 vpm). The results obtained show that the corrosion products are well localised on the surface. The aggregates formed are principally constituted of basic nitrate, sulphate and chloride of nickel and zinc. These studies showed that the corrosion of the material is due to the presence of porosities in the gold and nickel layers. X-ray analysis (SEM/EDS) revealed the presence of carbon in these porosities, probably related to the presence of organic compounds in the electrolytic coating baths. During the galvanic corrosion of nickel and zinc, the carbon is rejected to the periphery of the aggregates. The amount of carbon was determined by Van De Graaff analysis, by (d,p) nuclear reaction. Some treatments of the material by ion implantation (titanium or titanium and nitrogen or helium) have been realised in order to suppress the porosities of the gold layer. These treatments lead to a remarkable improvement of the corrosion resistance of the material. © 2000 Académie des sciences / Éditions scientifiques et médicales Elsevier SASatmospheric corrosion / nickel / brass / gold coating / ion implantation     

Synthesis,spectroscopy and structures of halogen and sulfur-bridged dinuclear silver(I) complexes with N1-substituted thiophene-2-carbaldehyde thiosemicarbazone

The reactions of silver(I) halides (Cl or Br) with thiophene-2-carbaldehyde N¹-methyl thiosemicarbazone (HttscMe) in the presence of Ph₃P (1:1:1 molar ratio) yield halogen-bridged dimers, [Ag₂(μ-X)₂(η¹-S-HttsMe)₂(PPh₃)₂] (X = Cl, 1; Br, 2). The use of 2,2′-bipyridine in lieu of Ph₃P in the reaction of silver(I) chloride with HttscMe yields the sulfur-bridged dimer, [Ag₂(μ-S-HttscMe)₂(η¹-HttsMe)₂] · 2CHCl₃ 3. The substituents have altered the nature of bridge between the two silver atoms. The Ag···Ag separation (3.4867(5) Å) in complex 3 is less than that in the halogen-bridged dimers (3.734(4) Å 1; 3.746(5) Å 2). Unlike PPh₃ the co-ligand 2,2′-bipyridine did not coordinate to the silver center, but was necessary for crystallization in the reaction with the thio-ligand. NMR spectroscopy revealed that the complexes remained unchanged in the solution state (CDCl₃).     

Partial charge transfer of poly(vinylferrocene)-coated latex particles adsorbed on pyrolytic graphite electrode

As a model of an electrode reaction of a big particle, vinylferrocene immobilized on polystyrene latex particles were synthesized by copolymerization with styrene sulfonate and styrene. They had almost mono-dispersed spheres with 1.2 μm in diameter, and each had 3.1 × 10⁷ ferrocene units. The particles adsorbed on pyrolytic graphite electrode (PGE) showed the redox activity for the ferrocene unit in NaBF₄ aqueous solution. Particles without the sulfonate group had no electroactivity, and hence the electroactivity needs ionic micro-environment around the ferrocene unit. From the faradaic charge of the ferrocene unit, the electroactive sites per particle were estimated to be about 8% of the whole immobilized ferrocene units. A model of this partial charge transfer was proposed, in which the particles are adsorbed in hollows of the rough surface of the PGE.     

Evaluation of tungsten–rhodium coating on an integrated platform as a permanent chemical modifier for cadmium,lead, and selenium determination by electrothermal atomic absorption spectrometry

A tungsten–rhodium coating on the integrated platform of a transversely heated graphite atomizer is proposed as a permanent chemical modifier for the determination of Cd, Pb, and Se by electrothermal atomic absorption spectrometry. It was demonstrated that coating with 250 μg W+200 μg Rh is as efficient as the conventional Mg(NO₃)₂+NH₄H₂PO₄ or Pd+Mg(NO₃)₂ modifiers for avoiding most serious interferences. The permanent W–Rh modifier remains stable for 300–350 firings of the furnace, and increases tube lifetime by 50%–100% when compared to pyrolytic carbon integrated platforms. Also, there is less degradation of sensitivity during the atomizer lifetime when compared with the conventional modifiers, resulting in a decreased need of re-calibration during routine analysis. The characteristic masses and detection limits achieved using the permanent modifier were respectively: Cd 1.1±0.4 pg and 0.020 μgL⁻¹; Pb 30±3 pg and 0.58 μgL⁻¹ and Se 42±5 pg and 0.64μgL⁻¹. Results from the determination of these elements in water reference materials were in agreement with the certified values, since no statistical differences were found by the paired t-test at the 95% level.     

Preparation and characterization of microsized K2Ta2O3F6 with ellipsoidal morphology by anodization

Ellipsoidal K₂Ta₂O₃F₆ particles with an average length of 2.79 μm and a diameter of 0.63 μm were synthesized by anodization in saturated solutions of potassium chloride containing 5 wt% HF. Microstructure and composition analysis were conducted by scanning electron microscopy, X-ray diffractometry and energy dispersive spectroscopy. Formation mechanism of this special morphology was given based on the experimental results.     

Separation performance of polyimide composite membrane prepared by dip coating process

The effects of the preparation conditions in a dip coating process on polyimide composite membranes have been investigated. Polyimide precursor obtained from pyromellitic dianhidride (PMDA) and 4,4′-oxydianiline (ODA) was mixed with triethylamine and poly(amic acid)tri-ethylamine salt (PAA salt) was made. An asymmetric polyimide membrane (PI-2080) as a supporting membrane was dipped in a PAA salt (concentration 0–5 wt.%) methanol solution. The coating layers of PAA salt were converted to these of polyimide by annealing at 200°C for 3 h in an ordinary vacuum oven.The performance of the polyimide composite membrane was evaluated by gas permeation (N₂, O₂, CO₂, at 1 kg/cm²) and pervaporation (feed: a 95 vol.% ethanol aqueous solution at 30–60°C). The composite membranes prepared using a coating solution of 5 wt.% PAA salt showed the CO₂/N₂ selectivity of over 25 on gas permeation, and separation factor α (H₂O/EtOH) of over 800 with a total flux of 0.21 kg/m² h on pervaporation.     

Formation of pore‐filled microfiltration membranes using a combination of modified interfacial polymerization and grafting

A novel method of fabricating pore‐filled membranes has been developed by coating a hydrophobic polyolefinic microfiltration membrane with polyethylenimine (PEI) to produce a chemically active surface. An evaporative coating technique was used to coat the internal surface of a polyolefinic membrane with PEI in chloroform (CHCl₃). The coated PEI was then crosslinked by naphthalene‐1,4‐disulfonyl chloride in carbon tetrachloride (CCl₄). The incorporation of the PEI coating changed the properties of the base membrane from hydrophobic to relatively hydrophilic; the nitrogens could be titrated, and the coating could not be washed out. 4,4′‐Azo‐bis(4‐cyanovaleryl chloride), a heat‐sensitive radical source, was incorporated into the coated membrane. The coated membrane, with incorporated azo compound, was heated to 75 °C in the presence of acrylic acid, 4‐(vinylpyridine), or styrene to give the corresponding grafted, pore‐filled membranes. The membranes exhibited hydraulic fluxes and pH valve effects consistent with molecular brushes grafted within the pores of the membranes. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 40: 242–250, 2002     

Two acridones and two coumarins from the roots of Paramignya trimera

Two acridones, paratrimerins C (1) and D (2), and two coumarins, paratrimerins E (3) and F (4), were isolated from the CHCl₃ and EtOAc extracts of Paramignya trimera (Rutaceae), together with twelve known compounds (5–16). Their structures were elucidated on the basis of spectroscopic data. All isolated compounds possessed significant α-glucosidase inhibitory activity in a concentration-dependent manner, and showed more potent inhibitory activity, with IC₅₀ values ranging from 14.6 to 112.2 μM, than the positive control acarbose (IC₅₀, 214.5 μM). The biosynthesis of the isolated coumarins and acridones was proposed.     

Effect of Fluoride or Chloride Ions on the Morphology of ZrO2 Thin Film Grown in Ethylene Glycol Electrolyte by Anodization

0.3 wt % ammonium fluoride (NH₄F) or ammonium chloride (NH₄Cl) was added to ethylene glycol (EG) as an active ingredient for the formation of anodic oxide comprising of ZrO₂ nanotubes (ZNTs) by anodic oxidation of zirconium (Zr) at 20 V for 10 min. It was observed that nanotubes were successfully grown in EG/NH₄F/H₂O with aspect ratio of 144.3. Shorter tubes were formed in EG/NH₄F/H₂O₂. This could be due to higher excessive chemical etching at the tip of the tubes. When fluoride was replaced by chloride in both electrolytes, multilayered oxide resembling pyramids was observed. The pyramids have width at the bottom of 3-4 μm and the top is 1-2 μm with 10.7 μm height. Oxidation of Zr in EG/NH₄Cl/H₂O₂ was rater rapid. The multilayered structure is thought to have formed due to the re-deposition of ZrO₂ or hydrated ZrO₂ on the foil inside pores formed within the oxide layer. XRD result revealed an amorphous structure for as-anodized samples regardless of the electrolytes used for this work.     

Dyed polyvinyl chloride films for use as high-dose routine dosimeters in radiation processing

Characteristics of the polyvinyl chloride (PVC) films containing 0.11 wt% of malachite green oxalate or 6GX-setoglausine and about 100 μm in thickness were studied for use as routine dosimeters in radiation processing. These films show basically color bleaching under irradiation with ⁶⁰Co γ-rays in a dose range of 5–50 kGy. The sensitivity of the dosimeters and the linearity of dose-response curves are improved by adding 2.5% of chloral hydrate [CCl₃CH(OH)₂] and 0.15% hydroquinone [HOC₆H₄OH]. These additions extend the minimum dose limit to 1 kGy covering dosimetry requirements of the quality assurance in radiation processing of food and healthcare products. The dose responses of both dyed PVC films at irradiation temperatures from 20°C to 35°C are constant relative to those at 25°C, and the temperature coefficients for irradiation temperatures from 35°C to 55°C were estimated to be (0.43±0.01)%/°C. The dosimeter characteristics are stable within 1% at 25°C before and 60 days after the end of irradiation.     

A novel biomimetic logic gate for sensitive and selective detection of Pb(II) base on porous alumina nanochannels

A novel biomimetic logic gate sensor for Pb^2 + is established using porous alumina membrane nanochannels modified with morpholino and DNA. It is based on electrochemical detection, and the current response from the diffusion flux of Fe(CN)₆^3 − is influenced by the steric blockage and charge repulsion in nanochannels. A limit of detection (0.1 nM) and good linear range (0.1 nM–5 μM) for Pb^2 + analysis are achieved in the tenth cycle. The sensing strategy shows prospective application in drug release, artificial ion channels, DNA logic gates for controlling biomolecule, and ion translocation.     

Nanorods of transition metal oxalates: A versatile route to the oxide nanoparticles

A versatile route has been explored for the synthesis of nanorods of transition metal (Cu, Ni, Mn, Zn, Co and Fe) oxalates using reverse micelles. Transmission electron microscopy shows that the as-prepared nanorods of nickel and copper oxalates have diameter of 250 nm and 130 nm while the length is of the order of 2.5 μm and 480 nm, respectively. The aspect ratio of the nanorods of copper oxalate could be modified by changing the solvent. The average dimensions of manganese, zinc and cobalt oxalate nanorods were 100 μm, 120 μm and 300 nm, respectively, in diameter and 2.5 μm, 600 nm and 6.5 μm, respectively, in length. The aspect ratio of the cobalt oxalate nanorods could be modified by controlling the temperature.The nanorods of metal (Cu, Ni, Mn, Zn, Co and Fe) oxalates were found to be suitable precursors to obtain a variety of transition metal oxide nanoparticles. Our studies show that the grain size of CuO nanoparticles is highly dependent on the nature of non-polar solvent used to initially synthesize the oxalate rods. All the commonly known manganese oxides could be obtained as pure phases from the single manganese oxalate precursor by decomposing in different atmospheres (air, vacuum or nitrogen). The ZnO nanoparticles obtained from zinc oxalate rods are ～55 nm in diameter. Oxides with different morphology, Fe₃O₄ nanoparticles faceted (cuboidal) and Fe₂O₃ nanoparticles (spherical) could be obtained.     

Preparation of palladium composite membranes by modified electroless plating procedure

A thin palladium composite membrane was produced by modified electroless plating procedure. Compared with the conventional electroless plating procedure, the modified electroless plating procedure consists of the activation of a ceramic substrate by the sol–gel process of a Pd(II)-modified boehmite sol. Additionally, the infiltration of an electroless plating solution to a porous substrate during the deposition of palladium was employed with the filter device to improve adherence of a palladium layer to a substrate. The resulting membrane with a thickness of about 1 μm has a high compactness. The membrane shows a hydrogen selectivity of 20–130 for H₂/N₂, and a hydrogen flux of 1.8–87 m³/m²·h, depending on operation conditions.     

Layer-by-layer nanoparticle coatings on lignocellulose wood microfibers

The layer-by-layer (LbL) self-assembly technique was applied to deposit organized multilayers of TiO₂ or SiO₂ nanoparticles of 30–80 nm diameter, and 50-nm diameter halloysite clay nanotubes on softwood fibers. Fluorescent and scanning electron microscopy images showed complete nanoparticle coating on these fibers. The thickness of the two-layer coating was estimated as 46, 58, and 115 nm for TiO₂, SiO₂, and halloysite tubules, respectively, which corresponds to ca. 1 wt% nanoparticle loading of the fibers. The brightness test of paper handsheets prepared from nanocoated fibers showed that TiO₂ nanoparticle coating gave handsheet reflectance of 84% at 450 nm, which is 4% higher than the brightness of the control sample from virgin fibers. The paper handsheets prepared with nanoparticle-coated fibers had 30–50% higher porosity with tensile strength index retained close to the control sample.