铜印迹螯合树脂对金属离子的吸附特性

研究了铜印迹螯合树脂与非印迹螯合树脂对金属离子的吸附性能，结果表明：铜印迹树脂对Cu^2 、Ni^2 、Zn^2 的吸附量比非印迹树脂有显著增大,两者对Cu^2 的吸附速率均较快，其表观吸附速率分别为0．044s^-1和0．040s^-1；印迹树脂对Cu^2 的吸附可用Langmuir或Freundlish等温式来描述；其动态吸附曲线与离子的起始浓度相关；用0．5mol／L HCl即可快速洗脱吸附的Cu^2 ，树脂具有较强的再生能力，可以重复使用。     

Biosorption of nickel(II) and copper(II) ions from aqueous solution by Streptomyces coelicolor A3(2)

The biosorption of nickel(II) and copper(II) ions from aqueous solution by dried Streptomyces coelicolor A3(2) was studied as a function of concentration, pH and temperature. The optimum pH range for nickel and copper uptake was 8.0 and 5.0, respectively. At the optimal conditions, metal ion uptake was increased as the initial metal ion concentration increased up to 250 mg l(-1). At 250 mg l(-1) copper(II) ion uptake was 21.8% whereas nickel(II) ion uptake was found to be as high as 7.3% compared to those reported earlier in the literature. Metal ion uptake experiments were carried out at different temperatures where the best ion uptake was found to be at 25 degrees C. The characteristics of the adsorption process were investigated using Scatchard analysis at 25 degrees C. Scatchard analysis of the equilibrium binding data for metal ions on S. coelicolor A3(2) gave rise to a linear plot, indicating that the Langmuir model could be applied. However, for nickel(II) ion, divergence from the Scatchard plot was evident, consistent with the participation of secondary equilibrium effects in the adsorption process. Adsorption behaviour of nickel(II) and copper(II) ions on the S. coelicolor A3(2) can be expressed by both the Langmuir and Freundlich isotherms. The adsorption data with respect to both metals provide an excellent fit to the Freundlich isotherm. However, when the Langmuir isotherm model was applied to these data, a good fit was obtained for the copper adsorption only and not for nickel(II) ion.     

Vinyl polymerization-412: Polymerization of methyl methacrylate initiated by the system of polyethyleneglycol,copper(II) chloride and water

The polymerization of methyl methacrylate (MMA) was carried out with the system polyethyleneglycol (PEG), copper(II) chloride and water at 85°. The effects of the amount of each component on the conversion of MMA were studied. Some polymerization occurred even if copper(II) ion was not present. It is suggested that there were three reactions: (1) polymerization initiated by the complex of PEG, copper(II) ion and water, (2) polymerization by PEG in water, (3) in the water phase, inhibition by copper(II) ion. The polymerization proceeded through a radical mechanism.     

Electrochemically Generated Recognition Sites in Self‐doped Polyaniline Modified Electrodes for Voltammetric and Potentiometric Determination of Copper(II) Ion

Chemical recognition elements for copper(II) ion have been generated in electrodes modified with poly(aniline‐co‐metanilic acid), P(An‐co‐MA), membrane and the resulting electrodes were used as selective sensors for voltammetric and potentiometric determination of this ion in an extended pH range. The P(An‐co‐MA) membrane was electrodeposited from aqueous mixed monomer solutions of An and MA, without the presence of a supporting electrolyte. For generating the recognition elements, P(An‐co‐MA) modified electrodes were subjected to several consecutive reduction/oxidation potential steps in copper(II) ion solution. It seems that during these potential steps, the receptor sites of the membrane are adjusted to the size, complexing property and hard/soft nature of copper(II) ion. This electrochemically mediated templating process, provided a selective sensor for determination of copper(II) ion. The results of preconcentration/differential pulse anodic stripping voltammetry, indicated analytical relation between the peak current and concentration of copper(II) from 1.0×10⁻⁹ to 1.0×10⁻⁴ M. The interference effect of various metal ions was explored and it was found that only mercury and silver ions show a considerable interference. The sensor exhibited selective potentiometric response for copper(II) over a wide concentration range (1.0×10⁻⁸ to 1.0×10⁻³ M) with a Nernstian slope of 27.9±0.3 mV per decade of copper(II) ion activity.     

Reversed phase liquid chromatographic determination of organic acids using on-line complexation with copper(II) ion

We describe a simple and sensitive liquid chromatographic method for the analysis of organic acids using on-line complexation with copper(II) ion. Organic acids complexed with copper(II) ion were separated on a reversed-phase C18 column and detected by UV absorption at 240 nm. The copper(II) ion concentration in the mobile phase had a great influence on separation and sensitivity. A mobile phase consisting of 10 mM copper(II) sulfate in 5 mM sulfuric acid (pH 2.3) was used to separate nine organic acids (tartaric, malic, malonic, lactic, acetic, citric, maleic, succinic and fumaric acids). The detection limits of the examined organic acids calculated at S/N = 3 ranged from 0.6 to 100 μM. The detector signal was linear over three orders of magnitude of organic acid concentration. The method successfully measured organic acids in juice and vinegar samples.     

Application of the zone melting technique to metal chelate systems-IV Concentration of metal-8-hydroxyquinoline chelates in 8-hydroxyquinoline

The zone melting technique has been applied to 8-hydroxyquinoline containing trace amounts of various metal 8-hydroxyquinolates such as the nickel(II), cobalt(II), zinc(II) and copper(II) chelates. The metal chelate in each system was concentrated in the direction of zone travel. The highest concentrating effect was observed in the copper(II) chelate system. The concentration ratio, defined as the fraction of the metal chelate concentrated in the bottom 15% of the column, was determined after the 30th passage. A trace amount of copper ion extracted with a large excess of 8-hydroxyquinoline, was concentrated by means of the zone melting technique. The concentration ratio was 96%.     

Preparation and evaluation of a novel chiral stationary phase based on covalently bonded chitosan for ligand-exchange chromatography

A novel chiral stationary phase based on chitosan covalently bonded onto silica gels has been prepared and used for the separation of various alpha-amino acid enantiomers as well as alpha-hydroxycarboxylic acid enantiomers by chiral ligand-exchange chromatography with copper(II) as a complexing ion. The methanol content and copper(II) ion concentration in the eluent affected retentivity and enantioselectivity. Furthermore, a plausible chiral recognition mechanism for resolution of alpha-amino acids was proposed.     

Voltammetric Detection of Copper Ions on a Gold Electrode Modified with a N-methyl-2-naphthyl-cyclam film

A voltammetric sensor based on a methyl-naphthyl cyclam (1,4,8,11-tetraazacyclotetradecane) film deposited through dip coating on gold electrodes allowed the sensitive detection of copper (II). The obtained film was characterized in terms of the composition and morphology using Fourier transform infrared (FTIR) spectroscopy and atomic force microscopy. In the presence of divalent metallic ions (copper and nickel) and trivalent metallic ions (iron), at pH 7 and 7.7, the current density of the ionic oxidation peak maximum was determined using square wave voltammetry. The relative variation of this current density varies linearly with the base-ten logarithm of the ion concentration. From this calibration curve, a detection limit of 7?×?10^?12?M was obtained for copper (II) at pH 7. At this pH value, the sensitivity of detection of copper (II) was 2.5 times higher than for nickel (II) and 5.8 times higher than for iron (III). The methyl-naphthyl cyclam film-modified gold sensor was validated for the detection of copper in spiked urine samples.     

Homogeneous isotope exchange between copper(II) and bis(resacetophenone oxime)copper(II) complex

Isotope exchange behavior of bis(resacetophenone oxime)copper(II) complex with copper(II) in tri-n-butyl-phosphate and methanol medium has been studied. The studies were carried out at different temperatures varying the concentration of both metal ion and complex. The results show that the complex is labile in the kinetic sense. Increase in temperature increases the isotope exchange rate. The increase in concentration also results in enhancement of the rate of reaction.     

In vitro and in vivo stability investigations of Cu(II), Zn(II), Ca(II) and Gd(III) complexes with N,N'-bis(2-hydroxyiminopropionyl) propane-1,3-diamine

Formation constants of copper(II), zinc(II), calcium(II) and gadolinium(III) with N,N'-bis(2-hydroxyiminopropionyl) propane-1,3-diamine (L2) have been studied at 25 degrees C and an ionic strength of 0.15 mol dm(-3). The reasonably high formation constants of the copper with this ligand are due to the ease with which the metal ion deprotonates the amide moieties. The square-planar coordination of L2 towards copper as predicted from UV-visible data may also account for the high selectivity of L2 towards the metal ion. Octanol/water partition coefficients of Cu(II)-L2 complexes indicate that although these complexes are largely hydrophilic, approximately 1.86% of the [CuL2H(-1)] species goes into the octanol layer and hence may promote dermal absorption of copper with a calculated penetration rate of 1.24 x 10(-5) cm h(-1). The [CuL2H(-1)] complex which predominates at pH 7.4 is a poor mimic of native copper-zinc superoxide dismutase. Blood-plasma simulation studies predict that, despite the high concentration of zinc and calcium in vivo, L2 is able to increase the low-molecular-mass fraction of copper. Biodistribution experiments using 64Cu-labelled [CuL2H(-1)] indicate an initial high uptake of this species in the liver, but it is predominantly excreted through the renal system.     

Polymerization of vinylcarbazole on copper(II)-13X molecular sieves: Role of copper(II) salts

Copper(II)-exchanged-13X molecular sieves, prepared from four copper(II) salts, namely, sulfate, nitrate, chloride, and acetate, and their activities in the polymerization of N-vinylcarbazole at a fixed copper ion exchange level were studied. From the kinetic characteristics of polymerization it was established that the variation in activities of the Cu-exchanged sieves is due primarily to the difference in the pH of the original salt solution, which is responsible for the varying degree of proton exchange with the zeolite during copper ion exchange. A first-order dependence of the rate of polymerization was observed with respect to H⁺ ion concentration of the original copper-salt solution. It was further established that the rate of polymerization of exchanged copper ion, at a hypothetical zero proton concentration, is low. A mechanism of polymerization of NVC on copper-exchanged-13X zeolite was suggested on the basis of the results obtained.     

Spectrophotometric determination of oxalate ion with N,N'-diethyl-N,N'-[[4,4'-dihydroxy-1,1'-binaphthalene]-3,3'-diyl]bisbenzamide and copper(II).

A simple and rapid spectrophotometric method for the determination of oxalate ion was established by the fading of a colored complex between N,N'-diethyl-N,N'-[[4,4'-dihydroxy-1,1'-binaphthalene]-3,3'-diyl]bisbenzamide and copper(II). Beer's law was obeyed in the concentration range of 0.1 - 2.0 microg cm(-3) for oxalate ion, with an effective molar absorptivity at 533 nm and the relative standard deviation being 8.0 x 10(3) dm(3) mol(-1) cm(-1) and 1.0% (n = 5), respectively. This proposed method has excellent reproducibility, and was applied to recovery tests of oxalate ion in tap water and human urine; the results were satisfactory. This is suggested that the method is based on the reaction of copper(II) to copper(I) with oxalate ion.     

Extraction of lead(II) and copper(II) from salicylate media by tributylphosphine oxide.

Tributylphosphine oxide (TBPO) is proposed as an extractant for the extraction of lead(II) and copper(II) from salicylate media. The optimum conditions were evaluated by varying the experimental parameters, such as the pH, sodium salicylate concentration, tributylphosphine oxide (TBPO) concentration, shaking period and various diluents. The probable extracted species, deduced from log-log plots were Pb(HSal)2.2TBPO and Cu(HSal)2.2TBPO. The extraction took place through a solvation mechanism. The method permits the binary separation of lead(II) and copper(II) from commonly associated elements as well as the mutual separation of lead(II) and copper(II). The method is applicable to the determination of lead(II) and copper(II) in various alloys as well as environmental and pharmaceutical samples.     

Homogeneous isotope exchange between copper/II/ and copper/II/-resacetophenone phenylhydrazone complex

Isotope exchange of copper/II/ between bis/resacetophenone phenylhydrazone/ copper/II/ complex and copper/II/ in trin-butyl phosphate and methanol medium was studied. The experiments were carried out at different temperatures varying the concentration of both metal ion and the complex. The results show that the complex is kinetically labile. An increase in temperature increases the rate of isotope exchange. The increase in concentration also results in the enhancement of the rate of reaction.     

Dynamics of closure of zinc bis-porphyrin molecular tweezers with copper(II) ions and electron transfer

Zinc bis-porphyrin molecular tweezers composed of a N(4) spacer bound through pyridyl units to the meso position of porphyrins were synthesized, and the tweezers are closed by the coordination of a copper(II) ion inside the spacer ligand. The effect of the π-π interaction between the porphyrin rings in the closed conformation on the absorption spectra of multi-electron oxidized species and the reduction potentials were clarified by chemical and electrochemical oxidation of the closed form of the zinc bis-porphyrin molecular tweezers in comparison with the open form without copper(II) ion and the corresponding porphyrin monomer. The shifts in redox potentials and absorption spectrum of the porphyrin dication indicate a strong electronic interaction between the two oxidized porphyrins in the closed form, whereas there is little interaction between them in the neutral form. The dynamics of copper(II) ion coordination and subsequent electron transfer was examined by using a stopped-flow UV/Vis spectroscopic technique. It was confirmed that coordination of copper(II) occurs prior to electron-transfer oxidation of the closed form of the zinc bis-porphyrin molecular tweezers.     

Counterion exchange selectivity coefficients at water-in-oil microemulsion interface

The counterion binding at a water/Aerosol-OT (AOT)/heptane microemulsion interface was treated in the context of the pseudo-phase ion exchange formalism. Two approaches were used to determine the selectivity coefficient for copper/sodium counterion binding at the AOT microemulsion interface: measurements of the Cu(II) concentration taken up by the reverse micelle in a Winsor II microemulsion system and steady-state emission quenching measurements of an anionic water-solubilized probe, the tris-(4,4'-dicarboxy-2,2'-bipyridine) ruthenium (II) ion. In addition, the selectivity coefficient for methyl viologen/sodium at the microemulsion surface was determined by the same photophysical technique. The value for copper (II)/sodium exchange (K(Cu/Na)) is 1.1+/-0.3 and that for methyl viologen/sodium (K(MV/Na)) is 0.9+/-0.3. The results show that the pseudo-phase ion exchange model can be used to obtain the selectivity coefficient in a microemulsion system.     

A Selective Film Based on Poly(3‐octylthiophene) Doped with Dihydroxyanthraquinone Sulfonate

A stable film of poly(3‐octylthiophene)–dihydroxyanthraquinone sulfonate has been synthesized electrochemically in non‐aqueous solution. The incorporation of dihydroxyanthraquinone sulfonate as an anionic complexing ligand into poly(3‐octylthiophene) film during electropolymerization was achieved and copper ions were accumulated by reduction on the electrode surface. The presence of dihydroxyanthraquinone sulfonate during the electrochemical polymerization of 3‐octylthiophene is shown to impact the sensitivity and the stability of the organic conducting film electrode response. The electroanalysis of copper(II) ions using conducting polymer electrode was achieved by differential pulse anodic stripping voltammetry with remarkable selectivity. The analytical performance was evaluated and linear calibration graphs were obtained in the concentration range of 50–400 ng mL^?1 copper(II) ion for 240 seconds accumulation time and the limit of detection was found to be 7.8 ng mL^?1. To check the selectivity of the proposed stripping voltammetric method for copper(II) ion, various metal ions as potential interferents were tested. The developed method was applied to copper(II) determination in certified reference material, NWRI‐TMDA‐61, trace elements in fortified water.     

Voltammetric determination of mercury(II) at a carbon paste electrode in aqueous solutions containing tetraphenylborate ion

The determination of mercury(II) ions can be achieved by monitoring the decrease in the oxidation peak of the tetraphenylborate ion in the presence of this metal ion at a carbon paste electrode. The reaction between mercury(II) and the tetraphenylborate ion results in the formation of diphenylmercury, thus providing the method with good selectivity over other metal ions. Using anodic stripping voltammetry in a neutral electrolyte, a linear dependence of the decrease of peak height was observed on increasing the mercury(II) concentration in the range 1 x 10(-6)-8 x 10(-9)M mercury(II). Zinc(II), cadmium(II), lead(II), nickel(II), cobalt(II), tin(II), potassium(I) and ammonium(I) ions did not interfere at a 1000-fold concentration excess. Iron(III) and chromium(III) did not interfere at a 250-fold and 50-fold concentration excess, respectively. Following masking procedures, copper(II), bismuth(III) and silver(I) did not interfere at a 100-fold concentration excess. The method can be used to determine the concentration of mercury(II) in natural waters contaminated by this metal.     

Solubility and polarity parameters for pyridinecarboxamides and their complexes with copper(II) as determined by inverse gas chromatography

Pyridinecarboxamides and their complexes with copper(II) were characterized by means of inverse gas chromatography. The investigated amides were extractants of copper(II) from solutions with a high chloride concentration. Solubility and polarity parameters were used to quantitate the properties of the extractants. The influence of the extractant's structure upon its properties are presented and discussed as well as the dependence of the physicochemical parameters on the introduction of the metal ion into the molecular structure.     

Thermodynamic and biodistribution studies of Zn(II), Ca(II), Gd(III) and Cu(II) complexes of 3,3,9,9-tetramethyl-4,8-diazaundecane-2,10-dione dioxime

The thermodynamic equilibria of copper(II), zinc(II), calcium(II) and gadolinium(III) with 3,3,9,9-tetramethyl-4,8-diazaundecane-2,10-dione dioxime (L1) have been studied at 25 degrees C and an ionic strength of 0.15 mol dm(-3). Copper and gadolinium form stable complexes with the ligand while the corresponding zinc species are more than 9 log units less stable. No complexes between calcium and the ligand were detected. The low binding strength of L1 towards zinc is attributed to the square-planar coordination geometry forced on the metal ion by the ligand as revealed by molecular mechanics calculations and molecular dynamics simulations. Speciation calculations, using a computer model of blood plasma, indicate that, despite the high concentration of zinc(II) and calcium(II) in vivo, L1 is able to increase the low-molecular-mass fraction of copper in plasma. Octanol/water partition coefficient of [CuL1H(-1)] indicates that although this species is largely hydrophilic, approximately 6% of the complex goes into the octanol phase and hence may promote dermal absorption of copper by the same amount. The dermal penetration rate is calculated to be 4.0 x 10(-4) mm h(-1). The [CuL1H(-1)] complex, which predominates at pH 7.4, is a poor mimic of native copper-zinc superoxide dismutase. Biodistribution experiments using the 64Cu-labelled [CuL1H(-1)] complex indicate an initial high uptake of this species in the liver followed by redistribution into muscle. Only a small amount is excreted through the urine.