CuWO4促进金红石TiO2光催化降解苯酚及其可能机理

已知金红石光催化降解水中有机物的活性远低于锐钛矿和板钛矿。本文报道,加入少量钨酸铜能显著加快金红石光催化降解水中苯酚。反应速率增加的幅度不仅远高于在相同煅烧温度（600 ℃）下制得的锐钛矿和板钛矿,而且随金红石煅烧温度（150-800 ℃）的增加持续增加。这些现象说明通过加入助催化剂钨酸铜,高温焙烧温度合成的金红石所具有的高的固有光催化活性可以被开发出来。此外,在过量苯酚存在下,H₂O₂的生成量随钨酸铜的加入量而先增加后减少,并且该趋势与苯酚降解速率基本一致。钨酸铜的这种正效应归结于固态的钨酸铜,而不是溶于水中的铜离子。（光）电化学测试表明,体系发生了从受光激发的金红石到钨酸铜的电子转移。这将提高光生载流子的分离效率,从而增大了O₂还原和苯酚降解的速率。     

超临界水热极速合成异质结构H4SiW12O40/Bi2WO6光催化剂及其脱氮性能

采用超临界水热合成方式极速合成一种H_4SiW_(12)O_(40)/Bi_2WO_6光催化剂,通过X射线衍射(XRD)、场发射扫描电子显微镜(SEM)、透射电子显微镜(TEM)、比表面积及孔隙度(BET)测定对所合成催化剂的结构和性质进行了考察,并以吡啶含量为15 mg/g的模拟油对光催化剂的脱氮效果进行评价。结果表明,该光催化剂为二维纳米片自组装成的三维球状结构,其中,H_4SiW_(12)O_(40)与Bi_2WO_6不是简单的固载关系而是在超临界水热条件下生成一种新的晶相,正是由于这种晶相的存在,使得H_4SiW_(12)O_(40)牢固固载在Bi_2WO_6光催化剂本体上的同时,对光生载流子进行了有效疏导,提升了H_4SiW_(12)O_(40)/Bi_2WO_6光催化剂的使用寿命和光催化活性。本研究针对光催化剂制备周期与晶形发育的矛盾,将超临界水热技术与光催化剂模板导向合成技术有机结合,在获得良好晶形异质结构H_4SiW_(12)O_(40)/Bi_2WO_6光催化剂的同时明显缩短了光催化剂的制备周期,从而降低了催化剂的制备成本,攻克了光催化剂工业化应用的主要矛盾,所制备的H_4SiW_(12)O_(40)/Bi_2WO_6光催化剂轻质油脱氮效率达97%以上。     

钨酸铋对四环素光催化降解性能

采用水热法制备了钨酸铋催化剂,以空气为氧化剂,四环素为底物,考察了制备催化剂时溶液的酸度、降解反应时不同光源、光强度和催化剂量对钨酸铋的光催化降解四环素性能的影响.结果表明,当制备钨酸铋催化剂溶液的pH为1时,催化降解效果较好;当催化剂与四环素的物质的量之比为0.3∶1时,光照时间100 min,光催化降解率达66%;以钨酸铋为催化剂,太阳光光催化降解性能优于红外光和紫外光,太阳光强度越强,催化降解效果越好.     

微波液相法一步合成H3PW12O40/Bi2WO6光催化剂及其脱氮性能

采用微波液相法一步合成了固载型H₃PW₁₂O₄₀/Bi₂WO₆光催化剂. 通过紫外-可见漫反射光谱(UV-Vis)、 场发射扫描电子显微镜(SEM)、 表面积及孔隙度(BET)测定、 氨气程序升温脱附(NH₃-TPD)、 吡啶吸附红外光谱(Py-FTIR)和X射线衍射(XRD)对所合成催化剂的结构和性质进行了考察, 并以吡啶浓度为15 mg/g的模拟油对光催化剂的脱氮效果进行评价. 结果表明, 与传统浸渍固载法相比, 微波液相一步法不仅能高效合成H₃PW₁₂O₄₀/Bi₂WO₆光催化剂, 且所合成的催化剂能被低能量的光激发. 固载H₃PW₁₂O₄₀不但能提高Bi₂WO₆纳米颗粒的表面酸量, 还能通过改变Bi₂WO₆前驱液的酸强度来调控催化剂形貌. 在H₃PW₁₂O₄₀固载量为15%(质量分数), 微波功率为800 W, 反应时间为90 min条件下得到的H₃PW₁₂O₄₀/Bi₂WO₆的光催化脱氮活性最高, 在催化剂与模拟油质量比为1/300, 500 W氙灯光照60 min的最佳光催化反应条件下, 模拟油脱氮率达到92.63%.     

圆盘状Bi2WO6-BiPO4异质结的水热合成及光催化性能

采用水热法制备Bi2WO6-BiPO4异质结光催化剂．利用模拟太阳光照射下的罗丹明B降解实验评价了Bi2WO6-BiPO4复合物的光催化性能．结果表明,Bi2WO6-BiPO4光催化活性比Bi2WO6和BiPO4高得多．当Bi2WO6与BiPO4的摩尔比为1：1时复合光催化剂对罗丹明B的降解率最高．Bi2WO6-BiPO4催化活性增强主要归结为两者之间形成了有效的异质结结构,其内建电场能够促进光生载流子的分离．同时,Bi2WO6的加入增强了其对可见光的吸收．研究表明O2^· -和h^＋在光催化降解过程中是主要的活性物种.     

GO负载Bi2WO6二元复合光催化材料的制备及其表征研究

本实验通过水热法合成不同比例的氧化石墨烯(GO)/Bi₂WO₆新型二元复合光催化材料.利用X射线衍射(XRD)、扫描电子显微镜(SEM)及透射电子显微镜等技术来研究样品的结构和形貌.在可见光下,4%GO/Bi₂WO₆复合材料光催化降解效率最好,达到了72%.本实验以石墨烯为碳源,制备出二元复合材料,将其引入光催化体系,提升半导体光催化材料对目标物的富集能力,为复合光催化材料的制备提供了新思路.以期获得高可见光催化活性的GO/Bi₂WO₆二元复合材料并将其应用于更多领域,同时对环境中的污染物也实现了高效、稳定的去除,为研究水体环境污染的治理奠定了一定的理论与实践基础.     

Fe2O3掺杂对WO3光催化降解有机染料X3B的影响

发展高效的可见光催化剂是太阳能化学利用的一个挑战. 本文采用简单的混合方法, 制备了WO₃和Fe₂O₃的混合物, 研究了该复合氧化物在H₂O₂存在下光催化降解有机染料X3B的活性. 实验表明, 催化剂的光催化活性与其煅烧温度和Fe₂O₃含量有关. 最佳煅烧温度和Fe₂O₃含量分别等于400 °C 和1.0% (w). 根据自由基捕获电子顺磁共振(EPR)波谱分析, 复合氧化物产生羟基自由基的量远高于Fe₂O₃和WO₃. 我们推测, 这种协同效应来源于WO₃和Fe₂O₃之间的电荷转移, 从而加快半导体光生载流子的分离和X3B的光催化降解.     

Au/BiOBr/石墨烯复合物的制备及其苯酚降解光催化性能

采用水热法和多巴胺还原法制备了Bi OBr、Bi OBr/石墨烯和Au/Bi OBr/石墨烯光催化剂,并利用扫描电镜(SEM)、透射电镜(TEM)、X射线衍射(XRD)、光致发光光谱(PL)和紫外-可见漫反射光谱(UV-vis DRS)等方法表征其形貌、相结构、光谱吸收性质以及组成结构。在可见光照射下,通过对水相中苯酚的降解,考察了Au/Bi OBr/石墨烯复合光催化剂活性。结果表明,由于量子效率的提高、带隙能的降低(2.25 e V)以及Au表面等离子体共振,复合光催化剂表现出比纯Bi OBr更高的光催化活性,Au/Bi OBr/石墨烯复合物在180 min内对苯酚降解率可达到64%。     

水热反应条件对多孔球状Bi2WO6光催化剂结构及性能的影响

采用水热法制备了Bi₂WO₆光催化剂, 考察了水热反应温度、 水热反应时间及前驱体溶液pH值等条件对其对乙烯可见光催化活性的影响, 并通过X射线衍射(XRD)、 扫描电子显微镜(SEM)、 紫外-可见漫反射光谱(UV-Vis DRS)和比表面积分析等对催化剂的晶相组成、 微观形貌和光学性质等进行表征. 结果表明, 在水热反应温度为120 ℃、 水热反应时间为12 h、 前驱体溶液pH=0.5条件下, Bi₂WO₆光催化剂经过各向异性生长以及自组装奥斯特瓦尔德成熟(Ostwald ripening)过程, 形成由二维纳米薄片自组装的多孔微球状结构, 有效增大了与乙烯气体的接触面积, 禁带宽度降至2.86 eV, 可见光响应范围拓宽, 表现出优异的光催化性能, 在可见光下240 min内对乙烯的降解率达到13.69%.     

多酸掺杂Bi2O3-x/Bi光催化剂用于高效可见光催化降解四溴双酚A和NO去除

四溴双酚A(TBBPA)是一种重要的塑料添加剂和阻燃剂,广泛用于树脂、塑料、胶黏剂以及涂料中.它不仅是持久性的机污染物,还是一种内分泌干扰物,具有免疫毒性、神经毒性和细胞毒性.NOx,特别是NO,是主要的大气污染物之一,是形成PM2.5的重要前体,也容易引起酸雨,引发光化学烟雾、臭氧损耗、温室效应等,严重危害生态环境和...     

Flower-like Bi2WO6/ZnO composite with excellent photocatalytic capability under visible light irradiation

The photocatalytic ability of ZnO is improved through the addition of flower-like Bi₂WO₆ to prepare a Bi₂WO₆/ZnO composite with visible light activity. The composite is characterized by X-ray diffraction, transmission electron microscopy, scanning electron microscopy with UV–vis diffuse reflectance spectroscopy, X-ray photoelectron spectroscopy and N₂ adsorption-desorption isotherms. After modification, the band gap energy of Bi₂WO₆/ZnO is reduced from 3.2 eV for ZnO to 2.6 eV. Under visible light irradiation, the Bi₂WO₆/ZnO composite shows an excellent photocatalytic activity for degrading methylene blue (MB) and tetracycline. The photo-degradation efficiencies of (0.3:1) Bi₂WO₆/ZnO for MB and tetracycline are approximately 246 and 4500 times higher than those of bare ZnO, respectively, and correspondingly, the photo-degradation rates for the two pollutants are approximately 120 and 200 times higher than those with bare ZnO, respectively. Moreover, the photocatalyst of (0.3:1) Bi₂WO₆/ZnO exhibits a higher transient photocurrent density of approximately 4.5 μA compared with those of bare Bi₂WO₆ and ZnO nanoparticles. The successful recombination of Bi₂WO₆ and ZnO enhances the photocatalytic activity and reduces the band gap energy of ZnO, which can be attributed to the effective separation of electron–hole pairs. Active species trapping experiments display that [O₂]^? is the major species involved during photocatalysis rather than ?OH and h⁺. This study provides insight into designing a meaningful visible-light-driven photocatalyst for environmental remediation.     

Photocatalytic Degradation of 4-Chlorophenol by Gd-Doped β-Bi2O3 Under Visible Light Irradiation

Chlorophenols are known as persistent organic pollutants.Therefore,research on the removal of chlorophenols has attracted widespread attention.Hereto,the photocatalytic degradation of 4-chlorophenol by Gd-doped β-Bi2O3 under visible light irradiation was studied.The results showed that Gd-doped β-Bi2O3 materials are efficient catalysts for the photocatalytic degradation of chlorophenols,and 2%(atomic traction)Gd-doped β-Bi2O3 exhibits the highest photocatalytic activity for 4-chlorophenol degradation,because doping an appropriate amount of Gd^3+ions can effectively reduce the recombination rate of the photogenerated e^-/h^+pairs and then enhance the photocatalytic performance.When the reaction was carried out at 25 ℃ for 6 h using the 2% Gd-doped/β-Bi2O3 micro/nano materials of 200 mg and at air flow rate of 40 mL/min,the degradation rate of 4-chlorophenol reached 92.3%.Additionally based on the analysis of the products,it was speculated that the dominant photocatalytic degradation mechanism of 4-chlorophenol by Gd-doped β-Bi2O3 under visible light irradiation is an oxidative process involving an attack by the hydroxyl radical.     

异质结构AgCl/Bi2WO6微米球制备、表征及其光催化性能

首先利用水热法制备了由纳米片组装的粒径为1.5–2μm的Bi2WO6微球,然后在微球表面沉积了不同含量的AgCl (5 wt%,10wt%,20wt%,30wt%),制备了异质结构AgCl/Bi2WO6微球光催化剂.利用X射线粉末衍射、扫描电镜、透射电镜、红外光谱、紫外-可见漫反射吸收等手段对所制的光催化剂进行表征,并以紫外光和可见光分别为光源,罗丹明B为降解对象测试了其光催化活性,考察复合不同含量的AgCl对Bi2WO6光催化剂的性能影响.结果表明,沉积AgCl对Bi2WO6的晶体结构、表面性能和光吸收性能没有产生明显影响,但大幅度提高了Bi2WO6的紫外和可见光催化活性.当复合20wt%AgCl时, AgCl/Bi2WO6光催化活性最佳,紫外光下比纯Bi2WO6提高了2.2倍,可见光下提高了1倍.这主要是由于形成的AgCl/Bi2WO6异质结能有效抑制光生电子和空穴的复合,从而提了其光催化性能.     

WO_3/Bi_(12)SiO_(20)光催化降解气相苯

用气液反应法和化学溶液分解技术(CSD)分别制备了WO3和Bi12SiO20粉末,并将二者耦合,合成出WO3/Bi12SiO20复合光催化剂.以气相苯的降解为探针反应,考查了催化剂的光催化活性.结果表明:耦合后的WO3/Bi12SiO20催化剂的催化活性显著提高,其中30%(w)WO3/Bi12SiO20在紫外光下对苯的降解率明显优于P-25,而且催化剂具有一定的可见光响应能力.采用X射线衍射(XRD)、扫描电子显微镜(SEM)、X射线光电子能谱(XPS)、N2吸附-脱附(BET)和紫外-可见漫反射(UV-VisDRS)等手段对催化剂进行了表征.结果表明:WO3与Bi12SiO20之间存在良好的能带协同作用.WO3与Bi12SiO20耦合后,催化剂的光响应范围拓宽,光生电子和空穴能有效地分离,光生电子和空穴产生速率增大,所以催化剂活性提高.     

Effect of synthesis pH on the physicochemical properties of a synthesized Bi2WO6 and the type of substrate chosen,in assessing its photo-catalytic activities

Crystalline orthorhombic Bi₂WO₆ powders were synthesized by a hydrothermal method from aqueous solutions of Bi(NO₃)₃·5H₂O and Na₂WO₄·2H₂O over a range of three selected pH values (2.0, 5.0 and 7.0), using NaOH as precipitating agent. The as-prepared catalysts were characterized by XRD, BET, FE-SEM, TEM, XPS and UV-vis spectroscopy. The effect of pH-synthesis on crystallinity, morphologies, surface area and optical absorption properties, were investigated. Although the pH has a marked influence on morphology, the nature of the precipitating agent (NaOH or TEA) also influences the morphology and surface structure composition, as it is observed in the present work. Three different probe molecules were used to evaluate the photo-catalytic properties under two illumination conditions (UV and Visible): Methyl Orange and Rhodamine B were chosen as dye substrates and Phenol as a transparent substrate. The photo-catalytic activities are strongly dependent not only on the pH used in the synthesis but also on the nature of the chosen substrate in assessing the photo-catalytic activities. Results were compared with those obtained when using TiO₂(P25, Evonik) in the same experimental conditions. The photo-catalytic activity of one of the synthesised samples has been evaluated by exposing a mixture of Rhodamine B and Phenol in water, to different illumination conditions. Our results provide new evidences about the issue of whether dyes are suitable substrates to assess the activity of a photo-catalyst.     

亚硫酸盐协助中空Bi2WO6微球的光催化性能

本文利用亚硫酸盐与Bi2WO6协同作用,有效地提升其光催化活性。以甲基橙和抗生素环丙沙星(CIP)作为被降解物对该体系的光催化降解性能和机理进行了研究。结果表明:光催化活性增强主要原因为亚硫酸盐能与Bi2WO6的光生空穴及羟基自由基反应,不仅能生成新的活性物质亚硫酸自由基(SO3^2-),还能促进Bi2WO6光生电子—空穴对的分离。此外,还考察了催化剂的用量、和污染物的浓度对该体系光催化性能的影响。     

煅烧温度对花朵状钨酸铋光催化活性的影响

钨酸铋在水相体系中能光催化降解有机污染物,而对于钨酸铋光催化活性影响因素的研究非常少.本文研究了煅烧温度对花朵状钨酸铋光催化活性的影响.以钨酸钠和硝酸铋为原料,在160°C下水热反应20 h,合成催化剂,并经不同温度煅烧3 h.用X射线衍射(XRD)、拉曼(Raman)光谱、紫外-可见漫反射吸收光谱(UVVis DRS)和荧光(PL)光谱表征样品.结果表明,这些样品具有十分相似的相组成和电子结构.然而,对于水中苯酚的降解,钨酸铋的光催化活性显示出了很大的差异.钨酸铋的光催化活性随着煅烧温度的升高,先上升后下降,最优煅烧温度为350°C,并且不受样品比表面积大小的影响.这些样品的活性差异主要归结于钨酸铋的结晶度、吸光性和表面缺陷对其光生载流子分离效率的综合影响.     

Investigations on the Phase Transformation,Optical Characteristics,and Photocatalytic Activity of Synthesized Heterostructured Nanoporous Bi2O3–TiO2

Fine‐powdered, heterostructured, nanoporous Bi₂O₃–TiO₂ (BTO) was synthesized by a green approach using ultrasonication, with the mole ratio Bi/Ti of 1:1 and calcined at different temperatures. The physical and optical properties of the mixed oxides were investigated. The phase structure, as identified by X‐ray diffraction (XRD), showed the appearance of new phases as a function of the calcination temperature. Morphological examinations indicated the formation of a nanoporous structure with a drastic change in morphology at the calcination temperature of 850°C from a globule to a rod‐shaped structure, which further got transformed to a rocky appearance at 1200°C. Doping with Bi₂O₃ led to the lowering of the bandgap of TiO₂ from 3.25 to 2.5 eV. A BTO nanocatalyst calcined at 450°C exhibited promising photocatalytic activity for the degradation of quinalphos (QP) (92%) after a time interval of 100 min under visible light and at the optimum pH 8. The kinetics of degradation of QP showed that it follows a pseudo‐first‐order path with a rate constant 0.01267 min^?1. The synthesized BTO mixed oxide showed profound improvement in photocatalytic activity in the visible region as compared to TiO₂.