富勒烯掺杂NPB空穴传输层的有机电致发光器件

报道了不同掺杂浓度NPB：C₆₀（富勒烯）作为空穴传输层对有机电致发光器件性能的影响.采用真空热蒸镀方法,制作了ITO/ NPB：C₆₀ （x % ）/Alq₃/LiF/Mg:Ag结构的四种有机电致发光器件.当NPB：C₆₀的掺杂浓度是15％时,器件的启亮电压是4 V,最大亮度是11000 cd/m².然而,当NPB：C₆₀的掺杂浓度是20％时,器件的最大亮度降     

不同主体双发光层白色有机电致发光器件的性能研究

制备了结构为ITO/NPB/CBP:TBPe:rubrene/BAlq:Ir(piq)₂(acac)/BAlq/Alq₃/Mg:Ag的白色磷光有机电致发光器件.利用两种不同的主体材料,即用双载流子传输型主体材料CBP掺杂荧光染料TBPe及rubrene作为蓝光和橙黄光发光层;用电子传输型主体材料BAlq掺杂磷光染料Ir(piq)₂(acac)作为红色发光层.以上双发光层夹于空穴传输层NPB与具有电子传输性的阻挡层BALq之间.讨论了如何控制     

有机发光二极管的光致磁电导效应

制备了结构为ITO/CuPc/NPB/Alq₃/LiF/Al的常规有机发光二极管, 之后对器件采用波长为442 nm和325 nm的激光线进行照射产生激子, 并在小偏压下(保证器件没有开启)对激子的演化过程进行控制, 同时测量器件的光致磁电导(photo-induced magneto-conductance, PIMC). 实验发现, 不同于电注入产生激子的磁电导效应, PIMC在正、反小偏压下表现出明显不同的磁响应结果. 当给器件加上正向小偏压时, 器件的PIMC在0-40 mT范围内迅速上升; 随着磁场的进一步增大, 该PIMC增加缓慢, 并逐渐趋于饱和. 反向小偏压时, 器件的PIMC随着磁场也是先迅速增大(0-40 mT), 但达到最大值后却又逐渐减小. 通过分析外加磁场对器件光生载流子微观过程的影响, 采用'电子-空穴对'模型和超精细相互作用理论对正向偏压下的PIMC进行了解释; 反向偏压下因各有机层的能级关系, 为激子与电荷相互作用提供了必要条件, 运用三重态激子与电荷的反应机制可以解释PIMC出现高场下降的实验现象.     

室温下磁场对基于Alq3的有机电致发光器件的影响

制备了ITO/NPB/LiF/Alq₃/LiF/Al的器件,测量了该组器件效率和亮度的磁效应.结果表明,在50 mT磁场中,当LiF缓冲层厚度为0.8 nm时,器件的效率最大增加了12.4%,磁致亮度最大变化率17%.同时,制备的磷光器件ITO/NPB/LiF/CBP:6 wt% Ir(ppy)₃/BCP/Alq₃/ LiF/Al,在50mT磁场作用下,当LiF缓冲层的厚度为0.8 nm时,器件的效率最大增加12.1%.在Alq_{3 关键词： 有机发光 磁场 效率 磁致亮度}     

具有穿插界面结构的高效绿光有机电致磷光器件

以传统有机电致磷光器件ITO/NPB/CBP∶Ir(ppy)₃/BAlq/Alq₃/LiF/Al为研究对象,在NPB/CBP∶Ir(ppy)₃、CBP∶Ir(ppy)₃/BAlq及BAlq/Alq₃界面处构造交互穿插结构。器件的光电性能测试表明:交互穿插结构一方面能够降低电流密度,减少高电流密度下磷光猝灭中心的形成;另一方面能增加载流子复合界面面积,从而分散界面三线态激子,降低三线态-三线态激子的猝灭。此外,界面凸起的存在还有利于器件的光耦合输出。实验结果表明:当穿插厚度为10 nm,器件的最大电流效率达到34.0 cd/A,与传统器件的电流效率18.7 cd/A相比,提高了55%。     

4,4′,4″-三(N-3-甲基苯基-N-苯基氨基)三苯胺掺杂MoOx作为空穴传输层对有机太阳电池性能的影响

通过采用4,4′,4″-三(N-3-甲基苯基-N-苯基氨基)三苯胺 (m-MTDATA)掺入MoO_x作为器件的空穴传输层来提高酞菁铜(CuPc)/C₆₀小分子 有机太阳电池的效率. 采用真空蒸镀的方法制备了一系列器件, 其中结构为铟锡氧化物 (ITO)/m-MTDATA:MoO_x(3:1)(30 nm)/CuPc(20 nm)/C₆₀(40 nm)/4,7-二苯 基-1,10-菲罗啉 (Bphen)(8 nm)/LiF(0.8 nm)/Al(100 nm)的器件, 在AM1.5 (100 mW/cm²)模拟太阳光的照射条件下, 开路电压V_oc=0.40 V, 短路电流J_sc=6.59 mA/cm², 填充因子为0.55, 光电转换效率达1.46%, 比没有空穴传输层的器件ITO/CuPc(20 nm)/C₆₀(40 nm)/Bphen(8 nm)/LiF(0.8 nm)/Al(100 nm) 光电转换效率提高了38%. 研究表明, 加入m-MTDATA:MoO_x(3:1)(30 nm)空穴传输层减小了有机层和ITO电极之间的接触电阻, 从而减小了整个器件的串联电阻, 提高了器件的光电转换效率.     

芴-咔唑新型共聚物/PVK掺杂体系的电致发光特性研究

研究了新型的芴-咔唑共聚物(PFC)与聚乙烯咔唑(PVK)掺杂体系的光致发光和电致发光特性.制备了结构分别为indium-tin-oxide(ITO)/PVK:PFC/bathocuproine(BCP)/tris-(8-hydroxylquinoline)-aluminum (Alq₃) /Mg:Ag，ITO/PFC/BCP/Alq₃/Mg∶Ag和ITO/PVK/BCP/Alq₃/Mg∶Ag的三种有机电致发光器件.对器件的光电特性进行了测试.结果表明，掺杂体系中的PVK有效地抑制了固态膜中PFC激基缔合物的形成.掺杂器件在不同的外加电场作用下发生发光层位置的移动，通过调节外加电场，可以获得从绿光到蓝光的可见光发射.当外加电压大于7V时，掺杂器件的蓝色发光亮度达到1650cd/m²，推测其中可能存在从PVK到PFC的能量传递过程.     

一种改善红光顶发射OLED色纯度及角度依赖特性的方法研究

在Si/SiO₂衬底上生长金属银作为阳极,4,4,4-tris(3-methylphenylpheny-lamino)-triphenylamine(m-MTDATA):MoOx/m-MTDATA/N,N-bis-(1-naphthyl)-N,N-diphenyl-1,1-biphenyl-4,4-diamine(NPB)作为空穴注入及传输层,发光层采用4,4-N,N-dicarbazole-biphenyl(CBP)掺杂磷光染料(1-(phenyl)isoquinoline)iridium(III) acetylanetonate(Ir(piq)₂(acac))的结构,4,7-di-phenyl-1,10-phenanthroline(BPhen)作为空穴阻挡层及电子传输层,阴极为LiF(1 nm)/Al(2 nm)/Ag(20 nm)复合阴极结构.通过在光取出的复合阴极上方生长一层CBP光学覆盖层,有效地改善了复合阴极膜系的透射率,从而改善了顶发射结构的光学耦合输出特性,在提高器件的正向发光效率的同时还使色坐标往深红光区移动.并且生长光学覆盖层结构的器件角度依赖特性明显得到改善,这对于制作高显示质量的显示器件具有重要意义.在原有结构的基础上增加20 nm的NPB掺杂磷光染料Ir(piq)₂(acac)作发光层,从而得到双发光层结构为NPB:Ir(piq)₂(acac)(1%,20 nm)/CBP:Ir(piq)₂(acac)(1%, 20 nm).由于NPB具有较高的空穴迁移率,避免了由于光学厚度的增加而引起器件工作电压的大幅升高,而双发光层的结构有利于增大激子复合区域,提高辐射复合几率,减少非辐射损耗,实现主客体之间高效的三线态能量传递,相对单发光层顶发射结构,双发光层结构不仅提高了器件的发光效率,而且改善了器件的色坐标.     

有机/有机界面污染对有机电致发光器件稳定性的影响(英文)

有机电致发光器件的稳定性是其实用化面临的主要难题之一。为了研究有机/有机界面性质对有机电致发光器件稳定性的影响,采用溶液旋涂的NPB(NPBSC)作为器件的空穴传输层制备了两种异质结电致发光器件:ITO/NPBSC/Alq3/LiF/Al和ITO/NPBSC/NPB/Alq3/LiF/Al,对比研究了器件的发光性能和工作稳定性。研究结果表明:完全使用NPBSC作为空穴传输层的器件性能和稳定性都较差,这归因于不稳定的NPBSC/Alq3界面,在空气中旋涂制备NPB层时,空气中的水蒸气和氧气分子会粘附在空穴传输层表面,这样就会引起界面处Alq3分子的发光猝灭。插入10 nm真空蒸镀的NPB层可以显著地提高器件的发光性能和稳定性,10 nm的NPB层把污染界面与激子复合区界面分开,避免了水蒸气和氧气分子对Alq3分子的发光猝灭,器件的效率增加了1.15 cd/A,半衰期寿命提高了4倍。     

N掺杂改善黄色磷光有机电致发光器件的效率滚降

制备结构为ITO/HAT-CN/TAPC/TCTA/POAPF\:PO-01/Bphen/LiF/Al的黄色磷光器件,其效率滚降特性符合三重态-极化子淬灭模型;接着设计了一组单电子和单空穴器件,实验结果表明:发光层内的空穴是多子且PO-01俘获空穴,被PO-01俘获的多余空穴引起的激子淬灭是导致器件在高电流密度下效率剧烈滚降的原因;采用N掺杂的方法增加电子注入,可减少发光区内多余的空穴,改善器件载流子的平衡状况,降低多余空穴引起的激子淬灭,进而改善效率滚降。     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Measurement of nonlinear coefficient of optical fiber based on small chirped soliton transmission

We measure the waveform and phase curves of short optical pulses before and after transmission over different lengths of fibers by use of the pulse analyzer with the frequency-resolved optical gating (FROG),and numerically simulate pulse evolution under the experimental conditions.The nonlinear coefficient of the fiber is given by comparing the experimental results with the numerical ones.Difference between the experiment and numerical simulation is analyzed.     

Resonance scattering of canonical elastic shells in absorbing fluid medium

Resonance scattering of elastic spherical shell and cylindrical shell while the surrounding fluid medium has absorption is studied. The normal mode solution derived using exact elastic theory and the separation of variables is still applicable. However, the scattering form function has to be modified for the absorbing medium, otherwise the unreasonable result would be obtained. The backscattering form function in the absorbing medium is redefined, and the form function of elastic spherical and cylindrical shell with vacuum or solid matter filled is calculated in various absorption conditions. The results show that the absorption of surrounding fluid leads to notable attenuation of the coincidence resonances in the mid-frequency, but it has a little influence on the low-frequency resonance scattering induced by the filler inside the shell.     

Single-beam self-referenced phase-sensitive surface plasmon resonance sensor with high detection resolution

A versatile and low-cost single-beam self-referenced phase-sensitive surface plasmon resonance(SPR)sensing system with ultra-high resolution performance is presented.The system exhibits a root-mean-square phase fluctuation of ±0.0028.over a period of 45 min.i.e.a resolution of±5.2×10-9 refractive index units.The enhanced performance has been achieved through the incorporation of three design elements:a true single-beam configuration enabling complete self-referencing so that only the phase change associated with SPR gets detected,a differential measurement scheme to eliminate spurious signals not related to the sensor response,and the elimination of retardation drifts by incorporating temperature stabilization in the liquid crystal phase modulato .Our design should bring the detection sensitivity of non-labeling SPR biosensing closer to that achievable by conventional fluorescence-based techniques.     

Influences of SiO2 protective layers and annealing on the laser-induced damage threshold of Ta2O5 films

Ta2O5 films are prepared on BK7 substrates with conventional electron beam evaporation deposition.The effects of SiO2 protective layers and annealing on the laser-induced damage threshold (LIDT) of the films are investigated.The results show that SiO2 protective layers exert little influence on the electric field intensity(EFI)distribution,microstructure and microdefect density but increase the absorption slightly.Annealing iS effective on decreasing the microdefect density and the absorption of the films.Both SiO2 protective layers and annealing are beneficial to the damage resistance of the films and the latter is more effective to improve the LIDT.Moreover,the maximal LIDT of Ta2O5 films is achieved by the combination of SiO2 protective layers and annealing.     

A stereo matching algorithm using multi-peak candidate matches and geometric constraints

Gray cross correlation matching technique is adopted to extract candidate matches with gray cross correla- tion coefficients less than some certain range of maximal correlation coefficient called multi-peak candidate matches. Multi-peak candidates are extracted corresponding to three closest feature points at first. The corresponding multi-peak candidate matches are used to construct the model polygon. Correspondence is determined based on the local geometric relations between the three feature points and the multi-peak candidates. The disparity test and the global consistency checkout are applied to eliminate the remaining ambiguous matches that are not removed by the local geometric relational test. Experimental results show that the proposed algorithm is feasible and accurate.