Dispersion of single-walled carbon nanotubes in dimethylacetamide and a dimethylacetamide–cholic acid mixture

A way of dispersing single-walled carbon nanotubes in preparing stable suspensions with high concentrations of individual nanotubes in amide solvents is described. The obtained suspensions are studied via Raman spectroscopy. The dependence of the degree of single-walled carbon nanotube (SWNT) dispersion in individual and mixed amide solvents on the type of solvent, the mass of nanotubes, and the concentration of cholic acid is established. A technique for processing spectral data to estimate the diameters and chiralities of individual nanotubes in suspension is described in detail.     

Effects of surfactant and boron doping on the BWF feature in the Raman spectrum of single-wall carbon nanotube aqueous dispersions

We examine the Breit-Wigner-Fano (BWF) line shape in the Raman spectra of carbon single-wall nanotubes (SWNTs) dispersed in aqueous suspensions. Bundling and electronic effects are studied by comparing undoped SWNTs (C-SWNTs) to boron-doped nanotubes (B-SWNTs) in a variety of different surfactant solutions. For SWNTs dispersed with nonionic surfactants that are less effective in debundling than ionic surfactants, the Raman spectra retain a large BWF feature. However, we demonstrate that even for SWNTs dispersed as isolated nanotubes by ionic surfactants the BWF feature may be present and that the intensity of the BWF is highly sensitive to the specific surfactant. In particular, surfactants with electron-donating groups tend to enhance the BWF feature. Also, modification of the SWNT electronic properties by boron doping leads to enhanced surfactant dispersion relative to undoped C-SWNTs and also to modification of the BWF feature. These observations are in agreement with reports demonstrating an enhancement of the BWF by bundling but also agree with reports that suggest electron donation can enhance the BWF feature even for isolated SWNTs. Importantly, these results serve to caution against using the lack or presence of a BWF feature as an independent measure of SWNT aggregation in surfactant dispersions.     

The stability of suspensions of multiwalled carbon nanotubes in organic solvents in the presence of triton X-165

The stability of suspensions of multiwalled carbon nanotubes in isopropanol, toluene, and p-xylene has been studied. Suspensions of multiwalled carbon nanotubes in isopropanol (unlike those in toluene and p-xylene) display high aggregation stability, which is explained by the formation of repulsive solvation layers as a result of interactions between the polar solvent and nanotube surface. The addition of a nonionic surfactant, Triton X-165, noticeably increases aggregate sizes and accelerates sedimentation processes in nanotube suspensions in isopropanol, while, in toluene and p-xylene, the aggregate sizes decrease and the nanotube suspensions are stabilized.     

Improving the effectiveness of interfacial trapping in removing single-walled carbon nanotube bundles

Single-walled carbon nanotube (SWNT) bundles are selectively removed from an aqueous dispersion containing individually suspended carbon nanotubes coated with gum Arabic via interfacial trapping. The suspensions are characterized with absorbance, fluorescence, and Raman spectroscopy as well as atomic force microscopy (AFM) and rheology. The resulting aqueous suspensions have better dispersion quality after interfacial trapping and can be further improved by altering the processing conditions. A two-step extraction process offers a simple and fast approach to preparing high-quality dispersions of individual SWNTs comparable to ultracentrifugation. Partitioning of SWNTs to the liquid-liquid interface is described by free energy changes. SWNT bundles prefer to reside at the interface over individually suspended SWNTs because of greater free energy changes.     

Cellulose Nanocrystal-Assisted Dispersion of Luminescent Single-Walled Carbon Nanotubes for Layer-by-Layer Assembled Hybrid Thin Films

Highly stable single-walled carbon nanotube (SWNT) dispersions are obtained after ultrasonication in cellulose nanocrystal (CN) aqueous colloidal suspensions. Mild dispersion conditions were applied to preserve the SWNT length in order to facilitate the identification of hybrid objects. This led to a moderate dispersion of 24% of the SWNTs. Under these conditions, atomic force microscopy (AFM) and transmission electron microscopy (TEM) experiments succeeded in demonstrating the formation of hybrid particles in which CNs are aligned along the nanotube axis by a self-assembly process. These SWNT/CN dispersions are used to create multilayered thin films with the layer-by-layer method using polyallylamine hydrochloride as a polyelectrolyte. Homogeneous films from one to eight bilayers are obtained with an average bilayer thickness of 17 nm. The presence of SWNTs in each bilayer is attested to by characteristic Raman signals. It should be noted that these films exhibit a near-infrared luminescence signal due to isolated and well-separated nanotubes. Furthermore, scanning electron microscopy (SEM) suggests that the SWNT network is percolating through the film.     

Surfactant‐Dependent Charge Transfer between Polyoxometalates and Single‐Walled Carbon Nanotubes: A Fluorescence Spectroscopic Study

Hybridizations of redox‐active polyoxometalates (POMs) with single‐walled carbon nanotubes (SWNTs) have been widely investigated for their diverse applications. For the purpose of constructing high‐quality electronic devices, controlling charge transfer within POM/SWNT hybrids is an inevitable issue. As determined by means of fluorescence spectroscopy, electron transfer between SWNTs and a common POM dopant, phosphomolybdic acid (PMo₁₂), can be tuned simply by an alteration of nanotube surfactant type from anionic to nonionic. The mechanism is attributed to the influence of surfactant type on the stabilization of the electron donor–acceptor hybrid and effect of surfactant–nanotube interactions. These results will be important to control charge‐transport behavior in nanohybrids consisting of carbon nanotubes.     

非离子表面活性剂对多壁碳纳米管在乙醇中高浓度分散的作用

如果能在无需聚合物或共价官能团辅助的条件下, 将多壁碳纳米管(MWNTs)高浓度地分散在乙醇中, 那么向各种复合材料引入MWNTs的过程就会更加便捷. 为此, 制备了多种含有表面活性剂的多壁碳纳米管乙醇悬浮液并对比考查了它们的稳定性. 非离子表面活性剂Triton X-100 和Tween 65显示出了在乙醇中分散悬浮高浓度MWNTs的能力, 能够使1.0 g·L-1 MWNTs乙醇悬浮液的上层清液经240 h后浓度仍分别在0.50和0.35 g·L-1以上. 这样长时间稳定的、没有聚合物或共价官能团辅助的MWNTs乙醇悬浮液, 其浓度比文献报道的值高. 进一步探讨了这些非离子表面活性剂分子结构对于分散MWNTs的优势, 并直观给出了其吸附于碳纳米管表面的可能形式. X射线光电子能谱和透射电子显微镜的表征结果都证实了表面活性剂分子吸附于碳纳米管表面.     

Dispersing carbon nanotubes using surfactants

We review the recent advances in dispersing single-wall carbon nanotubes (SWNTs) using amphiphilic surfactants in aqueous solutions. Three aspects are discussed. (1) On the organization of surfactant molecules with SWNTs, new insights at the microscopic level arise from electron microscopy and detailed computer simulation studies. (2) Quantitative measurements, such as molecular interactions between functional groups and SWNTs, the coverage of surfactant on SWNTs in solution, the charge state of the SWNT/surfactant complex, and the degree of dispersion are critical for better understanding dispersion mechanisms and for the further development of dispersion strategies. (3) The thermodynamic driving forces and the role of metastability in the structure of surfactant dispersed SWNT suspensions are analyzed. An outlook on practical and fundamental issues is also presented.     

A biomimetic "polysoap" for single-walled carbon nanotube dispersion

As-synthesized single-walled carbon nanotubes (SWNTs) are bundled mixtures of different species. The current challenge in the field of carbon nanotube research lies in the processing and separation of SWNTs, which first require efficient dispersion of individual SWNTs in solvents. We report DNA-mimicking polysoap surfactants that disperse SWNTs in aqueous solutions more effectively than DNA. The polysoaps are synthesized by functionalizing the side chain of poly(styrene-alt-maleic acid) with aminopyrene. The synthetic nature of the polysoap opens a new approach to further optimization of not only SWNT dispersion efficiency but also multi-functional SWNT dispersing surfactant.     

Single-walled carbon nanotube-based coaxial nanowires: synthesis, characterization, and electrical properties

We report herein the template-directed synthesis, characterization, and electric properties of single-walled carbon nanotube- (SWNT-) based coaxial nanowires, that is, core (SWNT)-shell (conducting polypyrrole and polyaniline) nanowires. The SWNTs were first dispersed in aqueous solutions containing cationic surfactant cetyltrimethylammonium bromide (CTAB) or nonionic surfactant poly(ethylene glycol) mono-p-nonyl phenyl ether (O pi-10). Each individual nanotube (or small bundle) was then encased in its own micellelike envelope with hydrophobic surfactant groups orientated toward the nanotube and hydrophilic groups orientated toward the solution. And thus a hydrophobic region within the micelle/SWNT (called a micelle/SWNT hybrid template) was formed. Insertion and growth of pyrrole or aniline monomers in this hybrid template, upon removal of the surfactant, produce coaxial structures with a SWNT center and conducting polypyrrole or polyaniline coating. Raman and Fourier transform infrared (FTIR) spectroscopy and scanning (SEM) and transmission (TEM) electron microscopy were used to characterize the composition and the structures of these coaxial nanowires. The results revealed that the micellar molecules used could affect the surface morphologies of the resulting coaxial nanowires but not the molecular structures of the corresponding conducting polymers. Electric properties testing indicated that the SWNTs played the key roles in the conducting polymer/SWNT composites during electron transfer in the temperature range 77 K to room temperature. Compared with the SWNT network embedded in the conducting polymers, the composites within which SWNTs were coated perfectly by the identical conducting polymers exhibited higher barrier heights during electron transfer.     

In situ measurements of nanotube dimensions in suspensions by depolarized dynamic light scattering

We show that the dimensions of carbon nanotubes (CNTs) in suspension can be characterized by depolarized dynamic light scattering. Taking advantages of this in situ technique, we investigate in detail the influence of sonication procedures on the length and diameter of CNTs in surfactant solutions. Sonication power is shown to be particularly efficient at unbundling nanotubes, whereas a long sonication time at low power can be sufficient to cut the bundles with limited unbundling. We finally demonstrate the influence of CNT dimensions on the electrical properties of CNT fibers. Slightly varying the sonication conditions, and thereby the suspended nanotube dimensions, can affect the fibers conductivity by almost 2 orders of magnitude.     

Stability of the aqueous suspensions of nanotubes in the presence of nonionic surfactant

Stability of aqueous suspensions of multiwalled carbon nanotubes (MWNTs) and their percolation behavior are investigated. Nanotubes of aqueous suspensions show a strong tendency to aggregation and networking into electroconductive clusters. The percolation threshold of the electrical conductivity is rather low and of order phi approximately 0.01 (where phi is the volume fraction), which can be explained by the high aspect ratio of MWNTs. Strong influence of the nonionic surfactant Triton X-305 on the colloidal stability of aqueous suspensions of MWNTs is observed. Addition of surfactant exerts a stabilizing effect at surfactant concentration C(s) proportional to the weight concentration C of MWNTs, C(s) approximately C mol/dm3. The transient behavior of electrical conductivity in the aqueous suspensions is explained by fractal aggregation processes. The fractal dimension is shown to be sensitive to the surfactant concentration C(s).     

Comparative study on different carbon nanotube materials in terms of transparent conductive coatings

We compared conductive transparent carbon nanotube coatings on glass substrates made of differently produced single-wall (SWNT), double-wall, and multiwall carbon nanotubes. The airbrushing approach and the vacuum filtration method were utilized for the fabrication of carbon nanotube films. The optoelectronic performance of the carbon nanotube film was found to strongly depend on many effects including the ratio of metallic-to-semiconducting tubes, dispersion, length, diameter, chirality, wall number, structural defects, and the properties of substrates. The electronic transportability and optical properties of the SWNT network can be significantly altered by chemical doping with thionyl chloride. Hall effect measurements revealed that all of these thin carbon nanotube films are of p-type probably due to the acid reflux-based purification and atmospheric impurities. The competition between variable-range hoping and fluctuation-assisted tunneling in the functionized carbon nanotube system could lead to a crossover behavior in the temperature dependence of the network resistance.     

Thermal physics in carbon nanotube growth kinetics

The growth of single wall carbon nanotubes (SWNTs) mediated by metal nanoparticles is considered within (i) the surface diffusion growth kinetics model coupled with (ii) a thermal model taking into account heat release of carbon adsorption-desorption on nanotube surface and carbon incorporation into the nanotube wall and (iii) carbon nanotube-inert gas collisional heat exchange. Numerical simulations performed together with analytical estimates reveal various temperature regimes occurring during SWNT growth. During the initial stage, which is characterized by SWNT lengths that are shorter than the surface diffusion length of carbon atoms adsorbed on the SWNT wall, the SWNT temperature remains constant and is significantly higher than that of the ambient gas. After this stage the SWNT temperature decreases towards that of gas and becomes nonuniformly distributed over the length of the SWNT. The rate of SWNT cooling depends on the SWNT-gas collisional energy transfer that, from molecular dynamics simulations, is seen to be efficient only in the SWNT radial direction. The decreasing SWNT temperature may lead to solidification of the catalytic metal nanoparticle terminating SWNT growth or triggering nucleation of a new carbon layer and growth of multiwall carbon nanotubes.     

TURBISCAN MA 2000: multiple light scattering measurement for concentrated emulsion and suspension instability analysis

Emulsion or suspension destabilisation often results from coalescence or particle aggregation (flocculation) leading to particle migration (creaming or sedimentation). Creaming and sedimentation are often considered as reversible, while coalescence and flocculation spell disaster for the formulator. Thus, it is of prime importance to detect coalescence or cluster formation at an early stage to shorten the ageing tests and to improve the formulations. This work mainly concerns the independent and anisotropic scattering of light from an emulsion or suspension in a cylindrical glass measurement cell, in relation with the optical analyser TURBISCAN MA 2000. The propagation of light through a concentrated dispersion can be used to characterise the system physico-chemical stability. Indeed, photons undergo many scattering events in an optically thick dispersion before escaping the medium and entering a receiver aperture. Multiple scattering thus contributes significantly to the transmitted and backscattered flux measured by TURBISCAN MA 2000. We present statistical models and numerical simulations for the radiative transfer in a suspension (plane or cylindrical measurement cells) only involving the photon mean path length, the asymmetry factor and the geometry of the light receivers. We further have developed an imaging method with high grey level resolution for the visualisation and the analysis of the surface flux in the backscattered spot light. We compare the results from physical models and numerical simulations with the experiments performed with the imaging method and the optical analyser TURBISCAN MA 2000 for latex beads suspensions (variable size and particle volume fraction). We then present a few examples of concentrated emulsion and suspension instability analysis with TURBISCAN 2000. It is shown that the instrument is able to characterise particle or aggregate size variation and particle/aggregate migration and to detect these phenomena much more earlier than the operator's naked eye, especially for concentrated and optically thick media.     

Singlewall carbon nanotubes covered with polystyrene nanoparticles by in‐situ miniemulsion polymerization

This work is to make carbon nanotubes dispersible in both water and organic solvents without oxidation and cutting nanotube threads. Polystyrene‐singlewall carbon nanotube (PS‐SWNT) composites were prepared with three different methods: miniemulsion polymerization, conventional emulsion polymerization, and mixing SWNT with PS latex. The two factors, crosslinking and surface coverage of PS are important factors for the mechanical and electrical properties, including dispersion states of SWNT in various solvents. The PS‐SWNT composite prepared via a conventional emulsion polymerization showed SWNT bundles entirely covered with PS, whereas the PS‐SWNT composite prepared via a miniemulsion polymerization showed SWNT partially covered with crosslinked PS nanoparticles. The method of mixing SWNTs with PS latex did not show the well dispersed state of carbon nanotubes because PS was not crosslinked and was dissolved in a solvent, and nanotubes separated from PS precipitated. So the PS nanoparticle‐SWNT composite had lower electrical resistance, and higher mechanical strength than the other composites made by the latter two methods. As the amount of SWNT increases, the bare surface area of SWNT increases and the electrical conductivity increases in the composite made by the miniemulsion polymerization. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 573–584, 2006     

Rapidly functionalized, water-dispersed carbon nanotubes at high concentration

Microwave-assisted functionalization of single-wall carbon nanotubes (SWNTs) in a mixture of nitric and sulfuric acids was carried out to synthesize highly water-dispersible nanotubes. Stable concentrations as high as 10 mg/mL were obtained in deionized water that are nearly 2 orders of magnitude higher than those previously reported. This was after only 3 min of functionalization reaction. Fourier transform infrared spectra showed the presence of carboxylated (-COOH) and acid sulfonated (-SO(2).OH or -SO(3)(-) H(+)) groups on the SWNTs. On the basis of elemental analysis, it was estimated that one out of three carbon atoms was carboxylated, while one out of 10 carbon atoms was sulfonated. The Raman spectra taken both in aqueous dispersion and in the solid phase indicated charge transfer from the SWNT backbone to the functional groups. Scanning electron microscope images of thin films deposited from an aqueous suspension showed that the SWNTs were aligned parallel to one another on the substrate. The images also indicated some reduction in average length of the nanotubes. Transmission electron microscope images of thin films from a dilute methanol dispersion showed that the SWNTs were extensively debundled. Laser light scattering particle size measurements did not show evidence for the existence of particles in the 3-800 nm size range, indicating that the functionalized SWNTs might have dispersed to have formed a true solution. Moreover, the microwave-processed SWNTs were found to contain significantly smaller amounts of the original iron catalyst relative to that present in the starting nanotubes. The electrical conductivity of a thermally annealed thin membrane obtained from the microwave-functionalized SWNTs was found to be the same as that of a similar membrane obtained from a suspension of the starting nanotubes.     

Swelling the micelle core surrounding single-walled carbon nanotubes with water-immiscible organic solvents

Solvatochromic shifts in the absorbance and fluorescence spectra are observed when surfactant-stabilized aqueous single-walled carbon nanotube (SWNT) suspensions are mixed with immiscible organic solvents. When aqueous surfactant-suspended SWNTs are mixed with o-dichlorobenzene, the spectra closely match the peaks for SWNTs dispersed in only pure o-dichlorobenzene. These spectral changes suggest that the hydrophobic region of the micelle surrounding SWNTs swells with the organic solvent when mixed. The solvatochromic shifts of the aqueous SWNT suspensions are reversible once the solvent evaporates. However, some surfactant-solvent systems show permanent changes to the fluorescence emission intensity after exposure to the organic solvent. The intensity of some large diameter SWNT (n, m) types increase by more than 175%. These differences are attributed to surfactant reorganization, which can improve nanotube coverage, resulting in decreased exposure to quenching mechanisms from the aqueous phase.     

A triptycene-based approach to solubilising carbon nanotubes and C60

We describe herein the synthesis of a triptycene-based surfactant designed with the ability to solubilise single-walled carbon nanotubes (SWNTs) and C(60) in water through non-covalent interactions. Furthermore, an amphiphilic naphthalene-based surfactant with the same ability to solubilise SWNTs and C(60) has also been prepared. The compounds synthesised were designed with either two ionic or non-ionic tails to ensure a large number of supramolecular interactions with the solvent, thereby promoting strong solubilisation. The surfactants produced stable suspensions in which the SWNTs are dispersed and the surfactant/SWNT complexes formed are stable for more than one year. UV/Vis/NIR absorption spectroscopy, TEM and AFM were employed to probe the solubilisation properties of the dispersion of surfactants and SWNTs in water.     

Swelling the hydrophobic core of surfactant-suspended single-walled carbon nanotubes: a SANS study

Localized solvent environments form around single-wall carbon nanotubes (SWCNTs) because of the ability of surfactant molecules to solubilize immiscible organic solvents. Although these microenvironments around SWCNTs have already been used for fundamental and applied studies, small-angle neutron scattering (SANS) was used here to assess the size and shape of the solvent domains, their uniformity and distribution on the sidewalls, and the effect of solvent swelling on the aggregation state of the suspension. SANS measurements confirm both the formation of local solvent environments and that no irreversible aggregation of the nanotube suspension occurs after the SDS molecules are swollen in solvent. The results also corroborate prior conclusions based on photoluminescence that the structure formed is dependent of the nature of the solvent-surfactant combination; SWCNTs suspended with SDS and swelled with benzene have a more uniform coating on the sidewall than those swelled with o-dichlorobenzene. These differences can be important to understanding the effect of the local environment on the photoluminescence properties and the interaction of SWCNTs with interfaces.