Effect of BiFeO3 addition on Bi2O3–ZnO–Nb2O5 based ceramics

In this paper, low temperature sintering of the Bi₂(Zn_1/3Nb_2/3)₂O₇ (β-BZN) dielectric ceramics was studied with the use of BiFeO₃ as a sintering aid. The effects of BiFeO₃ contents and the sintering temperature on the phase structure, density and dielectric properties were investigated. The results showed that the sintering temperature could be decreased and the dielectric properties could be retained by the addition of BiFeO₃. The structure of BiFeO₃ doped β-BZN was still the monoclinic pyrochlore phase. The sintering temperature of BiFeO₃ doped β-BZN ceramics was reduced from 1000 °C to 920 °C. In the case of 0.15 wt.% BiFeO₃ addition, the β-BZN ceramics sintered at 920 °C exhibited good dielectric properties, which were listed as follows: ε_r = 79 and tan δ = 0.00086 at a frequency of 1 MHz. The obtained properties make this composition to be a good candidate for the LTCC application.     

Microwave dielectric properties of (1 − x)(Mg0.95Co0.05)TiO3–x(Na0.5La0.5)TiO3 ceramic system

The microstructures and the microwave dielectric properties of the (1 − x)(Mg_0.95Co_0.05)TiO₃–x(Na_0.5La_0.5)TiO₃ ceramic system were investigated. Two-phase system was confirmed by the XRD patterns and the EDX analysis. A co-existed second phase (Mg_0.95Co_0.05)Ti₂O₅ was also detected. The microwave dielectric properties are strongly related to the density and the matrix of the specimen. A new microwave dielectric material 0.88(Mg_0.95Co_0.05)TiO₃–0.12(Na_0.5La_0.5)TiO₃, possessing an excellent combination of dielectric properties: ε_r  22.36, Q × f  110,000 GHz (at 9 GHz), τ_f  2.9 ppm/°C), is proposed as a candidate dielectric for GPS patch antennas.     

Anodization of aluminium thin films on pSi and annihilation of strong luminescence from Al2O3

Photoluminescence (PL) of Al₂O₃ films obtained by anodization of thermally evaporated and annealed thin Al films on p⁺⁺Si in 0.3 M oxalic acid has been investigated. Thermal annealing at 200–950 °C under the dry nitrogen atmosphere was used for deactivation of luminescence centres. Luminescence from as grown films was broad and located at 425 nm. This luminescence reached to highest level after annealing at 600 °C. Maximum 10 min was required for full optical activation and prolonged annealing up to 4 h did not change the luminescence intensity. Because of deep levels, absorption band edge of as grown films was shifted to the lower energy which is 3.25 eV. Annealing above 800 °C reduced the PL intensity and this observation was correlated with the blue shift of band edge as the defects annealed out. Disappearing PL intensity and blue shift of band edge absorption after annealing at 950 °C was mainly attributed to the oxygen-related defects and partly to impurities that may be originated from oxalic acid. AFM results did not show any hexagonally ordered holes but uniformly distributed nanosized Al₂O₃ clusters that were clearly seen. XRD measurements on as grown Al₂O₃ showed only [1 1 0] direction of α phase. Debye–Scherer calculation for this line indicates that cluster size is 35.7 nm. XRD and AFM pictures suggest that nanocrystalline Al₂O₃ are embedded in amorphous Al₂O₃.     

The effect of Si surface nitridation on the interfacial structure and electrical properties of (La2O3)0.5(SiO2)0.5 high-k gate dielectric films

Thermal stability, interfacial structures and electrical properties of amorphous (La₂O₃)_0.5(SiO₂)_0.5 (LSO) films deposited by using pulsed laser deposition (PLD) on Si (1 0 0) and NH₃ nitrided Si (1 0 0) substrates were comparatively investigated. The LSO films keep the amorphous state up to a high annealing temperature of 900 °C. HRTEM observations and XPS analyses showed that the surface nitridation of silicon wafer using NH₃ can result in the formation of the passivation layer, which effectively suppresses the excessive growth of the interfacial layer between LSO film and silicon wafer after high-temperature annealing process. The Pt/LSO/nitrided Si capacitors annealed at high temperature exhibit smaller CET and EOT, a less flatband voltage shift, a negligible hysteresis loop, a smaller equivalent dielectric charge density, and a much lower gate leakage current density as compared with that of the Pt/LSO/Si capacitors without Si surface nitridation.     

Lithium ion conductive glass–ceramics with Li3Fe2(PO4)3 and YAG laser-induced local crystallization in lithium iron phosphate glasses

The glasses with the composition of 37.5Li₂O–(25 − x)Fe₂O₃–xNb₂O₅–37.5P₂O₅ (mol%) (x = 5,10,15) are prepared, and it is found that the addition of Nb₂O₅ is effective for the glass formation in the lithium iron phosphate system. The glass–ceramics consisting of Nasicon-type Li₃Fe₂(PO₄)₃ crystals with an orthorhombic structure are developed through conventional crystallization in an electric furnace, showing electrical conductivities of 3 × 10^− 6 Scm^− 1 at room temperature and the activation energies of 0.48 eV (x = 5) and 0.51 eV (x = 10) for Li⁺ ion conduction in the temperature range of 30–200 °C. A continuous wave Nd:YAG laser (wavelength: 1064 nm) with powers of 0.14–0.30 W and a scanning speed of 10 μm/s is irradiated onto the surface of the glasses, and the formation of Li₃Fe₂(PO₄)₃ crystals is confirmed from XRD analyses and micro-Raman scattering spectra. The crystallization of the precursor glasses is considered as new route for the fabrication of Li₃Fe₂(PO₄)₃ crystals being candidates for use as electrolyte materials in lithium ion secondary batteries.     

Bulk and surface properties of spinel Co3O4 by density functional calculations

DFT calculations are employed to bulk and surface properties of spinel oxide Co₃O₄. The bulk magnetic structure is calculated to be antiferromagnetic, with a Co²⁺ moment of 2.631 μ_B in the antiferromagnetic state. There are three predicted electron transitions O(2p) → Co²⁺(t_2g) of 2.2 eV, O(2p) → Co³⁺(e_g) of 2.9 eV and Co³⁺(t_2g) → Co²⁺(t_2g) of 3.3 eV, and the former two transitions are close to the corresponding experimental values 2.8 and 2.4 eV. The naturally occurring Co₃O₄ (1 1 0) and (1 1 1) surfaces were considered for surface calculations. For ideal Co₃O₄ (1 1 0) surfaces, the surface relaxations are not significant, while for ideal Co₃O₄ (1 1 1) surfaces the relaxation of Co²⁺ cations in the tetrahedral sites is drastic, which agrees with the experiment observation. The stability over different oxygen environments for possible ideal and defect surface terminations were explored.     

Conductivity and water uptake of Sr4(Sr2Nb2)O11·nH2O and Sr4(Sr2Ta2)O11·nH2O

The hydrated oxygen deficient complex perovskite-related materials Sr₄(Sr₂Nb₂)O₁₁·nH₂O and Sr₄(Sr₂Ta₂)O₁₁·nH₂O were studied at high water vapour pressures over a large temperature range by electrical conductivity measurements, thermogravimetry (TG), and X-ray powder diffraction (XRPD). In humid atmospheres both materials are known to exhibit protonic conductivity below dehydration temperatures, with peak-shaped maxima at about 500 °C. In this work we show that the peaks expand to plateaus of high conductivity from 500 to 700 °C at a water vapour pressure of 1 atm. However, in situ synchrotron XRPD of Sr₄(Sr₂Nb₂)O₁₁·nH₂O as a function of temperature shows that these observations are in fact coincident with melting and dehydration of a secondary phase Sr(OH)₂. The stability of Sr₄(Sr₂Nb₂)O₁₁·nH₂O and Sr₄(Sr₂Ta₂)O₁₁·nH₂O in humid atmospheres is thus insufficient, causing decomposition into perovskites with lower Sr content and SrO/Sr(OH)₂ secondary phases. This, in turn, rationalizes the observation of peaks and plateaus in the conductivity of these materials.     

焙烧温度对SiO2负载的Co3O4纳米粒子表面氧缺陷浓度和CO氧化催化性能的影响

以传统的浸渍法,在不同焙烧温度下制备了用于CO氧化反应的Co₃O₄/SiO₂催化剂．通过激光拉曼光谱(Raman)、X射线光电子能谱(XPS)、X射线衍射(XRD)、程序升温还原(TPR)和X射线吸收精细结构谱(XAFS)表征了该系列催化剂的结构．在所有的催化剂中,XRD和Raman光谱都只检测到了Co₃O₄晶相的存在．与Co₃O₄体相相比,XPS结果表明在200 oC焙烧的(Co₃O₄(200)/SiO₂)催化剂中Co₃O₄表面上存在着过量的Co²⁺．与XPS的结果一致,TPR结果表明Co₃O₄(200)/SiO₂催化剂中Co₃O₄表面上存在氧缺陷, 并且XAFS结果也表明Co₃O₄(200)/SiO₂催化剂中Co₃O₄具有更多的Co²⁺．提高焙烧温度使得过量的Co²⁺进一步氧化为Co³⁺,同时降低了表面氧缺陷浓度,从而得到计量比的Co₃O₄4/SiO₂催化剂．在所有的负载催化剂中Co₃O₄(200)/SiO₂催化剂表现出了最好的CO氧化催化性能,表明过量Co²⁺和表面氧缺陷的存在能够促进Co₃O₄催化CO氧化反应的活性.     

Charge-discharge characteristics of nanocrystalline Co3O4 powders via aerosol flame synthesis

Nanocrystalline Co₃O₄ powders were synthesized by aerosol flame synthesis (AFS) method for the anode of lithium ion batteries and the basic electrochemical properties were investigated. The effects of synthesis conditions and heat-treatment temperature on the morphology, crystallite size and electrochemical properties were investigated. As-prepared soot contained Co₃O₄, CoO and Co(OH)₂, which were eventually converted into cubic spinel Co₃O₄ by post heat treatment. The as-prepared particle size was in the range of 10-30 nm and grew to 50-85 nm by the heat treatment. With growing particle size and improved crystallinity, charge-discharge capacity and cycle performance were improved and the discharge capacity of the powder heat-treated at 700 °C was 571 mAh/g after 30 cycles, which was better than Co₃O₄ powder reported in the previous literature.     

The low temperature synthesis of Euand Dy activated Sr3Al2O6 nanophosphors by microwave method

The Eu²⁺and Dy³⁺ activated Sr₃Al₂O₆ (S3A2O-ED) nanophosphors were synthesized by a new microwave method. The S3A2O-ED sample calcined in microwave oven at around 650 °C for 20 min possesses a cubic Sr₃Al₂O₆ single phase. The sample showed small size (80–100 nm) and spherical shape. The excitation and emission spectra indicated that excitation broad band chiefly sited in visible range and the nanophosphors emitted strong light at 611 nm under around 473 nm excitation. Comparing with conventional method, the microwave synthesis of S3A2O-ED greatly decreased the calcining temperature and time. However, the brightness of S3A2O-ED nanophosphors was reduced. The change of luminescent intensity in S3A2O-ED nanophosphors could be attributed to the effect of surface energy.     

Catalytic performance of Mn3O4 and Co3O4 nanocrystals prepared by sonochemical method in epoxidation of styrene and cyclooctene

A simple sonochemical method was developed to synthesis uniform sphere-like Co₃O₄ and Mn₃O₄ nanocrystals. Epoxidation of styrene and cyclooctene by anhydrous tert-butyl hydroperoxide over the prepared Co₃O₄ and Mn₃O₄ nanocatalysts was investigated. The results of conversion activity were compared with bulk Co₃O₄ and Mn₃O₄. Under optimized reaction conditions, the nanocatalysts showed a superior catalytic performance as compared to the bulk catalysts. Powder X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), and BET surface area, were used to characterize and investigate the nanocatalysts.     

Organic acid assisted solid-state synthesis of Li1.2Ni0.16Co0.08Mn0.56O2 nanoparticles as lithium ion battery cathodes

Lithium-rich layered oxide Li_1.2Ni_0.16Co_0.08Mn_0.56O₂ can be referred as a crystalline mixture of Li₂MnO₃ and LiNi_0.4Co_0.2Mn_0.4O₂ at equal molar ratio. In the paper, the solid state reaction of M(AC)₂·4H₂O (M = Mn, Co and Ni) and LiOH·H₂O has been performed to obtain nanocrystalline Li_1.2Ni_0.16Co_0.08Mn_0.56O₂ using a small molecular organic acid (i.e., oxalic acid (OA), citric acid (CA) or tartaric acid (TA)) as additive. The introduction of organic acids can help to improve the layered structure and inhibit the particle growth of Li_1.2Ni_0.16Co_0.08Mn_0.56O₂, and the different organic acids exert distinct influences on the structural and electrochemical properties of Li_1.2Ni_0.16Co_0.08Mn_0.56O₂. In detail, the nanoparticles obtained in the presence of OA have the smallest average size of 50–150 nm, which correspondingly exhibit the highest initial discharge capacity of 267.52 mAh g⁻¹ at 0.1C and the best high-rate capability (e.g., 152.22 mAh g⁻¹, 5C) when applied as a lithium ion battery cathode. Furthermore, the active substance obtained from TA shows the best cycling stability and a discharge capacity of 202.42 mAh g⁻¹ can be retained after 50 cycles at 0.5C.     

Electrochemical characterization of Mn: Co3O4 thin films prepared by spray pyrolysis via aqueous route

Present investigation reports, spray pyrolytic deposition of Mn: Co₃O₄ thin films onto the stainless steel by spray pyrolysis, at the deposition temperature 573 ± 2 K via aqueous route. Prepared electrodes were characterized structurally and morphologically by means of XRD and SEM. Also optical and electrochemical characterizations were carried out in depth. Structural characterization confirms face centered cubic and tetragonal body centered crystal structures for Co₃O₄ and Mn₃O₄ respectively. The rough granular morphology is observed form SEM. Electrochemical study reveals the pseudo capacitive as well as double layer behavior with optimum specific capacitance 485.29 F/g at the scan rate 1 mV/s in 1 M KOH electrolyte. Specific energy, specific power and columbic efficiency were calculated using chronopotentiometric technique. Electrochemical impedance spectroscopy was carried out in the frequency range 1 mHz–1 MHz. Randles equivalent circuit parameters associated with the operative cell are reported.     

Comparison of magnetic properties in LixCoO2 and its decomposition products LiCo2O4 and Co3O4

Thermal stability of cathode material in the charged state is an important aspect for the safety of rechargeable batteries. It is well known that layered Li_xCoO₂ decomposes to a mixture of LiCoO₂ and Co₃O₄ at elevated temperatures. However, not many experimental evidences exist on intermediate phases those may form during the decomposition. Using magnetic measurements we show that it is possible to distinguish between the spinels LiCo₂O₄ and Co₃O₄ and thereby follow the decomposition of Li_xCoO₂. We characterize the magnetic behavior of thermally aged Li_xCoO₂ (x = 0.98, 0.76, 0.55) with increasing annealing time. Our results reveal the appearance of magnetic ordering in the thermally degraded products. The detailed analysis illustrates that the formation of Co₃O₄ is preceded by the formation of a meta stable LiCo₂O₄ phase.     

Preparation and magnetic properties of the conductive Co(1−x)NixFe2O4/polyaniline microsphere composites

Core-shell Co_(1−x)Ni_xFe₂O₄/polyaniline nanoparticles, where the core was Co_(1−x)Ni_xFe₂O₄ and the shell was polyaniline, were prepared by the combination of sol-gel process and in-situ polymerization methods. Nanoparticles were investigated by Fourier transform spectrometer, X-ray diffraction diffractometer, Scanning electron microscope, Differential thermal analysis and Superconductor quantum interference device. The results showed that the saturation magnetization of pure Co_(1−x)Ni_xFe₂O₄ nanoparticles were 57.57 emu/g, but Co_(1−x)Ni_xFe₂O₄/polyaniline composites were 37.36 emu/g. It was attributed to the lower content (15 wt%), smaller size and their uneven distribution of Co_(1−x)Ni_xFe₂O₄ nanoparticles in the final microsphere composites. Both Co_(1−x)Ni_xFe₂O₄ and PANI/Co_(1−x)Ni_xFe₂O₄ showed superparamagnetism.     

Electronic structure studies of the spinel CoFe2O4 by X-ray photoelectron spectroscopy

The spinel CoFe₂O₄ has been synthesized by combustion reaction technique. X-ray photoelectron spectroscopy shows that samples are near-stoichiometric, and that the specimen surface both in the powder and bulk sample is most typically represented by the formula (Co_0.4Fe_0.6)[Co_0.6Fe_1.4]O₄, where cations in parentheses occupy tetrahedral sites and those within square brackets in octahedral sites. The results demonstrate that most of the iron ions are trivalent, but some Fe²⁺ may be present in the powder sample. The Co 2p_3/2 peak in powder sample composed three peaks with relative intensity of 45%, 40% and 15%, attributes to Co²⁺ in octahedral sites, tetrahedral sites and Co³⁺ in octahedral sites. The O 1s spectrum of the bulk sample is composed of two peaks: the main lattice peak at 529.90 eV, and a component at 531.53 eV, which is believed to be intrinsic to the sample surface. However, the vanishing of the O 1s shoulder peak of the powder specimen shows significant signs of decomposition.     

Structural characteristics and morphology of SmxCe1−xO2−x/2 thin films

Effect of the deposition temperature (200 and 500 °C) and composition of Sm_xCe_1−xO_2−x/2 (x = 0, 10.9–15.9 mol%) thin films prepared by electron beam physical vapor deposition (EB-PVD) and Ar⁺ ion beam assisted deposition (IBAD) combined with EB-PVD on structural characteristics and morphology/microstructure was investigated. The X-ray photoelectron spectroscopy (XPS) of the surface and electron probe microanalysis (EPMA) of the bulk of the film revealed the dominant occurrence of Ce⁴⁺ oxidation state, suggesting the presence of CeO₂ phase, which was confirmed by X-ray diffraction (XRD). The Ce³⁺ oxidation states corresponding to Ce₂O₃ phase were in minority. The XRD and scanning electron microscopy (SEM) showed the polycrystalline columnar structure and a rooftop morphology of the surface. Effects of the preparation conditions (temperature, composition, IBAD) on the lattice parameter, grain size, perfection of the columnar growth and its impact on the surface morphology are analyzed and discussed.     

Synthesis and magnetic properties of single-crystalline BaFe12O19 nanoparticles

Rod-like and platelet-like nanoparticles of simple-crystalline barium hexaferrite (BaFe₁₂O₁₉) have been synthesized by the molten salt method. Both particle size and morphology change with the reaction temperature and time. The easy magnetization direction (0 0 l) of the BaFe₁₂O₁₉ nanoparticles has been observed directly by performing X-ray diffraction on powders aligned at 0.5 T magnetic field. The magnetic properties of the BaFe₁₂O₁₉ magnet were investigated with various sintering temperatures. The maximum values of saturation magnetization (σ_s=65.8 emu/g), remanent magnetization (σ_r=56 emu/g) and coercivity field (H_ic=5251 Oe) of the aligned samples occurred at the sintering temperatures of 1100 °C. These results indicate that BaFe₁₂O₁₉ nanoparticles synthesized by the molten salt method should enable detailed investigation of the size-dependent evolution of magnetism, microwave absorption, and realization of a nanodevice of magnetic media.     

Effect of Li2O and CoO-doping of CuO/Fe2O3 system on its surface and catalytic properties

Physicochemical, surface and catalytic properties of pure and doped CuO/Fe₂O₃ system were investigated using X-ray diffraction (XRD), energy dispersive X-ray analysis (EDX), nitrogen adsorption at −196 °C and CO-oxidation by O₂ at 80-220 °C using a static method. The dopants were Li₂O (2.5 mol%) and CoO (2.5 and 5 mol%). The results revealed that the increase in precalcination temperature from 400 to 600 °C and Li₂O-doping of CuO/Fe₂O₃ system enhanced CuFe₂O₄ formation. However, heating both pure and doped solids at 600 °C did not lead to complete conversion of reacting oxides into CuFe₂O₄. The promotion effect of Li₂O dopant was attributed to dissolution of some of dopant ions in the lattices of CuO and Fe₂O₃ with subsequent increase in the mobility of reacting cations. CoO-doping led also to the formation of mixed ferrite Co_xCu_1−xFe₂O₄. The doping process of the system investigated decreased to a large extent the crystallite size of unreacted portion of Fe₂O₃ in mixed solids calcined at 600 °C. This process led to a significant increase in the S_BET of the treated solids. Doping CuO/Fe₂O₃ system with either Li₂O or CoO, followed by calcination at 400 and 600 °C decreased its catalytic activity in CO-oxidation by O₂. However, the activation energy of the catalyzed reaction was not much affected by doping.     

Influence of ceramic oxide materials on lithium based potentiometric CO2 sensors

In these potentiometric sensors, a mixed binary carbonate sensing material consisting of 90 mol% Li₂CO₃ and 10 mol% BaCO₃ was modified by adding ceramic oxide materials such as SiO₂, B₂O₃, La₂O₃, Bi₂O₃, CeO₂ and In₂O₃ in different mol% concentrations. Various sensors mixed with these external oxides have shown good performance at operating temperatures below 300 °C. Scanning electron microscopy reveals that a glassy sensing phase is formed in the sensing bi-carbonate by the addition of ceramic oxides and sintered at 600 °C for 1 h. The sensor mixed with SiO₂:B₂O₃:Bi₂O₃ in 1:2:1 mol% showed an excellent response and recovery characteristics and followed a fair Nernstian behavior with a ΔEMF/dec value of −48.18 at as low as 150 °C. The decrease in operating temperature is attributed to the enhanced lithium ion migration through the glassy sensing phase of the sensing electrode.