氢氧化镁-硼酸锌复合阻燃剂辅助制备产率高和电容性能优异的煤焦油沥青基多孔碳

以煤焦油沥青为前驱体,氢氧化镁-硼酸锌复合阻燃剂为助剂,直接在空气条件下高温碳化制备了煤沥青基多孔碳,并探究其电化学性能。得益于阻燃剂的阻燃协同其活化、掺杂功能化作用,得到了高产率(55.1%)、多原子(N、B、O)掺杂且具有分级多孔结构的多孔碳。将其作为超级电容器电极材料,在三电极体系中0.5 A·g^-1电流密度下比电容可达344 F·g^-1。此外,以制备的多孔碳和壳聚糖基氨基酸质子盐凝胶电解质组装的柔性对称电容器具有29.3 Wh·kg^-1的高能量密度,在50 000次循环后电容保持率为96.9%,且在-25~75℃温度区间内可正常工作,显示出宽的温度使用范围。     

低成本硫掺杂多孔碳材料的制备及其超级电容性能

以廉价的胶态二氧化硅为模板,蔗糖为碳源,硫酸为预碳化试剂和硫源,通过硬模板法制备了相对廉价的硫掺杂多孔碳(SSC-T,T℃代表碳化温度)材料。采用多种表征方法对多孔碳材料的微观形貌、孔道结构、比表面积和表面硫物种进行了表征,探究了硫酸和碳化温度对多孔碳材料的微观形貌、孔道结构和比表面积的影响。结果表明,碳化温度对碳的孔结构、比表面积和硫元素的含量有显著的影响,其中900℃碳化得到的样品SSC-900具有最大的比表面积、孔体积和比电容,远高于未加入硫酸制备的碳材料SC-900,表明硫酸的加入可以提高碳材料的比表面积、孔体积,进而提高碳材料的比电容。与昂贵的有序介孔碳CMK-3相比,SSC-900具有成本更低、孔径更大和电容性能更好的优点。在以6.0 mol·L^-1 KOH为电解质的三电极体系中,在0.5 A·g^-1的电流密度下,SSC-900的比电容可以达到357 F·g^-1,而SC-900和CMK-3的比电容分别仅为152和266 F·g^-1。电容贡献分析表明,SSC-900的双层电容值和赝电容值均高于SC-900。此外,SSC-900在0.5 A·g^-1的电流密度下循环10 000次后仍能保持98.4%的初始比电容。     

低成本硫掺杂多孔碳材料的制备及其超级电容性能

以廉价的胶态二氧化硅为模板,蔗糖为碳源,硫酸为预碳化试剂和硫源,通过硬模板法制备了相对廉价的硫掺杂多孔碳(SSC-T,T℃代表碳化温度)材料。采用多种表征方法对多孔碳材料的微观形貌、孔道结构、比表面积和表面硫物种进行了表征,探究了硫酸和碳化温度对多孔碳材料的微观形貌、孔道结构和比表面积的影响。结果表明,碳化温度对碳的孔结构、比表面积和硫元素的含量有显著的影响,其中900℃碳化得到的样品SSC-900具有最大的比表面积、孔体积和比电容,远高于未加入硫酸制备的碳材料SC-900,表明硫酸的加入可以提高碳材料的比表面积、孔体积,进而提高碳材料的比电容。与昂贵的有序介孔碳CMK-3相比,SSC-900具有成本更低、孔径更大和电容性能更好的优点。在以6.0 mol·L^-1 KOH为电解质的三电极体系中,在0.5 A·g^-1的电流密度下,SSC-900的比电容可以达到357 F·g^-1,而SC-900和CMK-3的比电容分别仅为152和266 F·g^-1。电容贡献分析表明,SSC-900的双层电容值和赝电容值均高于SC-900。此外,SSC-900在0.5 A·g^-1的电流密度下循环10 000次后仍能保持98.4%的初始比电容。     

硼、氮共掺杂多孔碳的制备及其超电容性能

分别以含氮菲咯啉、四硼酸钾和醋酸锌为碳源、活化剂和模板,制备了B、N共掺杂多孔碳(BN-PC),并探究模板质量对BN-PC结构和储电性能的影响。当醋酸锌质量为5g时,所得BN-PC₅中B、N杂原子含量分别为 20.21%、18.29%。电化学测试结果表明,以6 mol·L^-1 KOH为电解液,BN-PC₅电极展现出高的比电容(在0.05 A·g^-1电流密度下为255 F·g^-1)、优异的倍率性能(在20A·g^-1电流密度下为188F·g^-1)和卓越的循环稳定性(在5 A·g^-1的电流密度下循环10 000次比电容保持率为97%)。以3 mol·L^-1 ZnSO₄为电解液,在平均功率密度为56W·kg^-1时,BN-PC₅电容器的能量密度可达27Wh·kg^-1。     

硼、氮共掺杂多孔碳的制备及其超电容性能

分别以含氮菲咯啉、四硼酸钾和醋酸锌为碳源、活化剂和模板,制备了B、N共掺杂多孔碳(BN-PC),并探究模板质量对BN-PC结构和储电性能的影响。当醋酸锌质量为5 g时,所得BN-PC₅中B、N杂原子含量分别为20.21%、18.29%。电化学测试结果表明,以6 mol·L^-1KOH为电解液,BN-PC₅电极展现出高的比电容(在0.05 A·g^-1电流密度下为255 F·g^-1)、优异的倍率性能(在20 A·g^-1电流密度下为188 F·g^-1)和卓越的循环稳定性(在5 A·g^-1的电流密度下循环10 000次比电容保持率为97%)。以3mol·L^-1ZnSO₄为电解液,在平均功率密度为56 W·kg^-1时,BN-PC₅电容器的能量密度可达27 Wh·kg^-1。     

超高比表面积氮掺杂多孔碳材料的制备及其超级电容性能

以蔗糖为碳源、尿素为氮源、草酸钾为活化剂,通过简单的研磨和高温碳化制备了具有超高比表面积(大于3 000 m²·g^-1)的氮掺杂多孔碳材料。采用多种手段对多孔碳材料的微观形貌、比表面积、孔结构和表面氮物种进行了表征,探究了不同温度下草酸钾和尿素对碳材料的比表面积、氮含量和超级电容性能的影响。结果表明,仅使用草酸钾作为活化剂制备的碳材料KC-800的比表面积为1 114 m²·g^-1,而同时使用草酸钾和尿素制备的样品KNC-800的比表面积高达3 033 m²·g^-1。在以6.0mol·L^-1 KOH为电解液的三电极体系中,当电流密度为0.5 A·g^-1时,KNC-800的比电容为405 F·g^-1,而KC-800的比电容仅为248 F·g^-1。这表明草酸钾和尿素的加入显著提高了多孔碳材料的比表面积和超级电容性能。电容贡献分析表明,KNC-800的双电层电容值和赝电容值均...     

超高比表面积氮掺杂多孔碳材料的制备及其超级电容性能

以蔗糖为碳源,尿素为氮源,草酸钾为活化剂,通过简单的研磨和高温碳化制备了具有超高比表面积(大于3 000 m²·g^-1)的氮掺杂多孔碳材料。采用多种手段对多孔碳材料的微观形貌、比表面积、孔结构和表面氮物种进行了表征,探究了不同温度下草酸钾和尿素对碳材料的比表面积、氮含量和超级电容性能的影响。结果表明,仅使用草酸钾作为活化剂制备的碳材料KC-800 的比表面积为 1 114 m2·g^-1,而同时使用草酸钾和尿素制备的样品 KNC-800 的比表面积高达 3 033 m²·g^-1。在以 6.0mol·L^-1 KOH 为电解液的三电极体系中,当电流密度为 0.5 A·g^-1时,KNC-800 的比电容为 405 F·g^-1,而 KC-800 的比电容仅为248 F·g^-1。这表明草酸钾和尿素的加入显著提高了多孔碳材料的比表面积和超级电容性能。电容贡献分析表明,KNC-800的双电层电容值和赝电容值均高于KC-800。KNC-800在电流密度为0.5 A·g^-1时经过10 000次循环后仍能保持98.3%的初始比电容,表现出优异的循环性能。     

水溶性壳聚糖制备多孔碳/氧化镍复合材料及其电化学电容行为

将水溶性壳聚糖碳化得到多孔碳材料, 然后制备了多孔碳/NiO复合材料. 透射电子显微镜(TEM), X射线衍射(XRD)和N₂吸-脱附实验等结构表征显示, 材料具有富含介孔的孔道结构. 循环伏安(CV), 恒流充放电等电化学测试表明, 复合材料具有良好的电化学电容性能. 其中Ni/C质量比为2:20时, 复合材料在0.1 A·g^-1电流密度下比容量可达355 F·g^-1, 而且经过1500次循环比容量仍保持99%左右, 表现出良好的循环稳定性.     

静电纺丝制备多孔碳纳米纤维及其电化学电容行为

采用静电纺丝技术,以聚丙烯腈(PAN)/醋酸锌为前驱体制备复合纳米纤维,随后经碳化、酸化获得多孔碳纳米纤维.扫描电子显微镜(SEM)观察发现,碳纳米纤维表面分布大量孔洞.N2吸脱附等温曲线(BET)测试材料比表面积达413m2·g-1.循环伏安法(CV)和恒流充放电(CP)性能测试表明:多孔碳纳米纤维具有较好的电化学性能,在1A·g-1的电流密度下比电容达275F·g-1.相比碳纳米纤维比容量提高了162%.     

多孔碳材料的化学气相后处理及其超级电容性能

以廉价的椰壳为原料制备了高比表面积的多孔碳材料,然后在密闭的反应釜中以硝酸蒸汽对多孔碳材料进行了后处理,制备了亲水性更好的多孔碳材料。采用扫描透射电子显微镜(TEM)、物理吸附、X射线粉末衍射(XRD)、拉曼光谱(Raman)和接触角测试对材料的微观形貌、孔道结构、组成和亲水性进行了表征,探究了不同温度下硝酸蒸汽对多孔碳材料的形貌、结构的影响,并采用循环伏安法、恒电流充放电法和交流阻抗法考察了多孔碳材料的超级电容性能。结果表明,经过硝酸蒸汽处理后的多孔碳材料的比表面积和孔体积均有所降低,且随着处理温度的升高,降低得更加明显,而亲水性却越来越好。电化学测试结果表明,经过100℃硝酸蒸汽处理的多孔碳材料(CSC-100)具有最佳的超级电容性能。在以6 mol·L^-1 KOH为电解液的三电极体系中,当电流密度为0.5 A·g^-1时CSC-100的比电容可达452.9 F·g^-1,而未经硝酸蒸汽处理的多孔碳材料(CSC)的比电容仅为350.4 F·g^-1。电容贡献分析表明CSC-100良好的亲水性和表面官能团不仅提高了双电层电容,也提高了赝电容。     

Preparation of flame retardant and thermal insulation polystyrene foams via high internal phase emulsion template

Expanded polystyrene foam (EPSF), valued for its excellent insulation properties, faces a significant flammability challenge due to its cellular structure. Traditional flame retardant methods such as physical blending and layer-by-layer assembly have poor applicability to EPSF. Therefore, it is necessary to find other more effective methods for synthesizing flame-retardant EPSF. The high internal phase emulsion (HIPE) template is one of the simplest and most commonly used methods for synthesizing porous materials, which have features such as adjustable pore structures and high porosity. In this work, ammonium polyphosphate (APP)/starch was added to the dispersed phase of the HIPE to prepare the flame-retardant EPSF by one-pot method. The morphology, thermal stability and flame retardancy of the foams were investigated. When the addition of APP/starch (the weight ratio is 1:1) reached 30 wt.%, the peak heat release rate (PHRR), total heat release (THR), and total smoke release (TSR) of the composite foam decreased by 74.7%, 65.9%, and 24.7%, respectively, compared to the pure PS foam. Meanwhile, its limiting oxygen index (LOI) value reached 25.8%, and the UL-94 rating reached V-1 level, indicating significant improvement in flame retardancy. This study provides an effective strategy for synthesizing flame-retardant porous materials.     

Preparation of phosphorylated chitosan‐coated carbon microspheres as flame retardant and its application in unsaturated polyester resin

In this work, phosphorylated chitosan‐coated carbon microspheres (PCH@CMS) was successfully synthesized. Obtained PCH@CMS used as flame retardant was added into unsaturated polyester resin (UPR). Fourier infrared spectroscopy (FTIR) and X‐ray electron spectroscopy (XPS) results indicated that C═O, P─O, and P═O appeared on the surface of PCH@CMS. Compared with UPR, the residues of UPR/PCH@CMS‐10 at 800°C under nitrogen and air atmospheres increased by 9.0 and 3.9 wt%, respectively, and the peak heat release rate (pHRR) and the peak smoke release rate (pSPR) of UPR/PCH@CMS‐3 decreased by 18.9% and 23.5%, respectively. Limiting oxygen index (LOI), thermogravimetric analyzer (TG), and cone calorimeter test (CCT) results showed that the addition of PCH@CMS could enhance the flame retardancy and smoke suppression of the UPR composites. Moreover, the residues after CCT were characterized by scanning electron microscopy (SEM), XPS, and laser Raman spectroscopy (LRS). Based on the above results, the flame retardant mechanism of PCH@CMS was proposed. The carbon layer produced by the UPR/PCH@CMS composites was tortuous and could suppress the heat and pyrolysis product exchange with UPR matrix.     

Synergistic effects and mechanism of multiwalled carbon nanotubes with magnesium hydroxide in halogen-free flame retardant EVA/MH/MWNT nanocomposites

The synergistic effects and mechanism of multiwalled carbon nanotubes (MWNTs) with magnesium hydroxide (MH) in halogen-free flame retardant EVA/MH/MWNT nanocomposites have been studied by cone calorimeter test (CCT), limiting oxygen index (LOI), thermogravimetric analysis (TGA), torque test, morphological evolution experiment, and scanning electron microscopy (SEM). The data obtained from the CCT, LOI, and TGA show that suitable amount of MWNTs has synergistic effects with MH in the EVA/MH/MWNT nanocomposites. The MWNTs can considerably decrease the heat release rates and mass loss rate by about 50-60%, prolongate the combustion time to near two times, and increase the LOI values by 5% when 2 wt% MWNTs substitute for the MH in the EVA/MH/MWNT samples. The TGA data also show that the synergistic effects of MWNTs with MH apparently increase the thermal degradation temperatures and final charred residues of the EVA/MH/MWNT samples. The experimental observations from the torque, morphological evolution tests, and SEM give positive evidences that the synergistic mechanism of MWNTs with MH can be described to: (i) the increase of melt viscosity because of network structure formation of MWNTs in the EVA/MH matrix; (ii) the enhancement of thermo-oxidation stability due to the MWNTs' mechanical strength and integrity of the charred layers in the EVA/MH/MWNT nanocomposites; (iii) the formation of compact charred layers promoted by MWNTs acted as heat barrier and thermal insulation. All the above-mentioned factors efficiently enhance thermal and flame retardant properties and protect the EVA/MH/MWNT nanocomposite materials to be burning.     

中温煤沥青基碳量子点的制备与结构解析

以中温煤沥青为碳源，采用HNO₃预处理结合球磨过程及双氧水氧化刻蚀的方法制备沥青基荧光碳量子点，以CQDs的收率和荧光量子产率为目标，获得最优制备条件：反应时间6 h、H₂O₂加入量100 mL （c-CQDs），此时，CQDs收率和荧光量子产率分别为6.3%和11.2%，且尺寸均匀、粒径分布在4-14 nm。延长反应时间至8 h （a-CQDs），碳量子点团聚；H₂O₂用量增加至120 mL （b-CQDs）则导致碳量子点氧化过度，颗粒小且杂乱无章。对不同条件下所制备的CQDs进行XPS、红外光谱、热重、¹³C NMR、Raman和晶相分析，探究反应条件对CQDs结构的影响规律。结果表明，就碳含量而言，a-CQDs > b-CQDs > c-CQDs，氧元素含量则为b-CQDs > c-CQDs > a-CQDs。各CQDs结构中C主要以芳碳形式存在，c-CQDs的C=O、O-C=O含量最高，而b-CQDs的C-O含量最高，¹³C NMR分析发现CQDs中表征平均芳环尺寸大小的X_b约为0.5，相应地，其平均芳环数约为3。     

煤沥青与石油沥青混合调制道路沥青的研究

采用高效剪切分散仪考察了调配温度、调配时间、搅拌方法等工艺对煤沥青混合石油沥青性能的影响,对优选的样品进行了离析实验、抗老化性能及流变性能评价。结果表明,调配工艺对煤沥青在石油沥青中的分散有重要影响,调配温度的升高、调配时间的延长能促进煤沥青在石油沥青中分散但也会导致调配沥青的老化;煤沥青粒径对调配沥青性能有重要影响,对优选样品的进一步评价表明,调配沥青有好的耐高温流变性能和抗热氧老化性能,储存稳定性可以解决。     

Preparation of halogen-free flame retardant polyacrylonitrile via hydrolyzing and grafting with diphenylphosphinyl chloride

Abstract

Halogen-free flame retardant polyacrylonitrile (PAN) was prepared via hydrolyzing the nitrile groups of PAN using aqueous sodium carbonate solution/hydrogen peroxide followed by grafting with diphenylphosphinyl chloride. The structure of original PAN, hydrolyzed PAN (HPAN), and flame retardant PAN (FR-PAN) samples were characterized using Fourier transform infrared spectroscopy, X-ray photoelectron spectroscopy, X-ray diffraction, and ¹H NMR spectroscopy. The thermal properties of the materials were assessed using thermogravimetric analysis. The FTIR spectroscopy indicates that a carbonyl group is present in hydrolyzed HPAN and some characteristic PAN absorption peaks decreased slightly upon hydrolysis. The XPS results show that FR-PAN contained phosphorus, indicating that diphenylphosphinyl chloride has been grafted onto HPAN, which is in accordance with the phenomenon of the self-extinguishing phenomena of FR-PAN during burning experiments. The TG curves indicate the presence of a char residue for FR-PAN of 45% at 800?°C, a higher char residue than that of original PAN (39%). Therefore, FR-PAN displays better thermal stability and char forming capability than does the untreated polymer.     

金属改性与碳包覆的多孔硅微球复合材料的制备及其电化学储锂性能

以工业级SiAl合金微球为前驱物,采用多步刻蚀-热处理策略,制备了金属(Sb-Sn)改性与碳包覆的多孔硅微球复合材料(pSi/Sb-Sn@C)。pSi/Sb-Sn@C具有以 Sb-Sn改性的多孔硅微球(pSi/Sb-Sn)为核、碳包覆层为壳的三维结构。碳外壳可以提高多孔硅微球的电子导电性和机械稳定性,有利于获得稳定的固体电解质界面(SEI)膜;而三维多孔核可以促进锂离子的扩散,增加嵌/脱锂活性位,缓冲嵌锂过程中的体积膨胀。此外,活性金属(Sb-Sn)的引入能够提高复合材料的导电性,并可以贡献一定的储锂容量。由于其特殊的组成和独特的微观结构,pSi/Sb-Sn@C复合材料在1.0 A·g^-1电流密度下充放电300次后的可逆容量为1 247.4 mAh·g^-1,显示了良好的高速率储锂性能和优异的电化学嵌/脱锂循环稳定性。     

A hierarchical porous carbon membrane from polyacrylonitrile/polyvinylpyrrolidone blending membranes:Preparation,characterization and electrochemical capacitive performance

Novel hierarchical porous carbon membranes were fabricated through a simple carbonization procedure of well-defined blending polymer membrane precursors containing the source of carbon polyacrylonitrile （PAN） and an additive of polyvinylpyrrolidone （PVP）, which was prepared using phase inversion method. The as-fabricated materials were further used as the active electrode materials for supercapacitors. The effects of PVP concentration in the casting solution on structure feature and electrochemical capacitive performance of the as-prepared carbon membranes were also studied in detail. As the electrode material for supercapacitor, a high specific capacitance of 278.0 F/g could be attained at a current of 5 mA/cm2 and about 92.90% capacity retention could be maintained after 2000 charge/discharge cycles in 2 mol/L KOH solution with a PVP concentration of 0.3 wt% in the casting solution. The facile hierarchical pore structure preparation method and the good electrochemical capacitive performance make the prepared carbon membrane particularly promising for use in supercapacitor.     

A hierarchical porous carbon membrane from polyacrylonitrile/polyvinylpyrrolidone blending membranes: Preparation,characterization and electrochemical capacitive performance

Novel hierarchical porous carbon membranes were fabricated through a simple carbonization procedure of well-defined blending polymer membrane precursors containing the source of carbon polyacrylonitrile (PAN) and an additive of polyvinylpyrrolidone (PVP), which was prepared using phase inversion method. The as-fabricated materials were further used as the active electrode materials for supercapacitors. The effects of PVP concentration in the casting solution on structure feature and electrochemical capacitive performance of the as-prepared carbon membranes were also studied in detail. As the electrode material for supercapacitor, a high specific capacitance of 278.0 F/g could be attained at a current of 5 mA/cm² and about 92.90% capacity retention could be maintained after 2000 charge/discharge cycles in 2 mol/L KOH solution with a PVP concentration of 0.3 wt% in the casting solution. The facile hierarchical pore structure preparation method and the good electrochemical capacitive performance make the prepared carbon membrane particularly promising for use in supercapacitor.