| 状态方程实验用铜多台阶靶制备工艺 |
| |
| 引用本文： | 谢军, 邢丕峰, 杜凯, 等. 状态方程实验用铜多台阶靶制备工艺[J]. 强激光与粒子束, 2009, 21(10). |
| |
| 作者姓名： | 谢军 邢丕峰 杜凯 黄燕华 孙涛 易泰民 童维超 袁光辉 李朝阳 杨蒙生 郑风成 |
| |
| 作者单位： | 1.中国工程物理研究院 激光聚变研究中心, 四川 绵阳 621 900;;;2.哈尔滨工业大学 精密工程研究所, 哈尔滨 1 50001 |
| |
| 基金项目： | 国家高技术发展计划项目 |
| |
| 摘 要： | 采用单点金刚石切削技术，通过合理的刀具设计、夹具设计及工艺过程设计，确定了加工工艺参数，完成了厚度几μm至几十μm的无氧铜多台阶靶的制备。通过触针式轮廓仪,台阶仪,白光干涉仪对表面轮廓及粗糙度进行了测量。结果表明：通过单点金刚石切削技术加工成形的铜多台阶靶，各台阶表面均方根粗糙度小于50 nm，工件表面轮廓平直，台阶垂直度较好。采用阿基米德原理对材料密度进行测量，加工成形后密度为(8.945±0.074) g/cm3,接近材料理论密度。
|
| 关 键 词： | 单点金刚石车削 多台阶 铜 靶 |
| 收稿时间： | 1900-01-01; |
Fabrication of Cu multi-step target used in EOS experiment |
| |
| xie jun, xing pifeng, du kai, et al. Fabrication of Cu multi-step target used in EOS experiment[J]. High Power Laser and Particle Beams, 2009, 21. |
| |
| Authors: | Xie Jun Xing Pifeng Du Kai Huang Yanhua Sun Tao Yi Taimin Tong Weichao Yuan Guanghui Li Zhaoyang Yang Mengsheng Zheng Fengcheng |
| |
| Affiliation: | 1. Research Center of Laser Fusion,CAEP,P.O.Box 919-987,Mianyang 621900,China;;;2. Research Institute of Precision Engineering,Harbin Institute of Technology,Harbin 150001,China |
| |
| Abstract: | The copper multi-step target with several to several tens of microns in thickness used in equation of state(EOS) experiment was produced by single point diamond turning(SPDT) technology. Parameters of finish process are given by rational tool design, clamp design and technical process design. The surface roughness is characterized by profile testing instrument, profilometer and white light interferometer. The results indicate that surface root mean square roughness of copper multi-step target by SPDT is less than 50 nm. The density of target material is tested by Archimedes principle. The result showed that the density of the copper mutil-step target is （8.945±0.074） g/cm3. |
| |
| Keywords: | multi-step copper target |
| 本文献已被 万方数据 等数据库收录！ |
| 点击此处可从《强激光与粒子束》浏览原始摘要信息 |
|
点击此处可从《强激光与粒子束》下载免费的PDF全文 |
|
