| 数字图像相关曲面拟合法相关系数修正算法的实验研究 |
| |
| 引用本文： | 俞海,郭荣鑫,夏海廷,颜峰,张玉波,何天淳.数字图像相关曲面拟合法相关系数修正算法的实验研究[J].实验力学,2013,28(5):586-594. |
| |
| 作者姓名： | 俞海 郭荣鑫 夏海廷 颜峰 张玉波 何天淳 |
| |
| 作者单位： | 昆明理工大学 工程力学系, 云南省先进材料力学行为与微观结构设计高校重点实验室, 云南昆明 650500;昆明理工大学 工程力学系, 云南省先进材料力学行为与微观结构设计高校重点实验室, 云南昆明 650500;昆明理工大学 工程力学系, 云南省先进材料力学行为与微观结构设计高校重点实验室, 云南昆明 650500;昆明理工大学 工程力学系, 云南省先进材料力学行为与微观结构设计高校重点实验室, 云南昆明 650500;昆明理工大学 工程力学系, 云南省先进材料力学行为与微观结构设计高校重点实验室, 云南昆明 650500;云南大学, 云南昆明 650500 |
| |
| 基金项目： | 云南省应用基础研究基金面上资助项目(2011FB029);高等学校博士学科点专项科研基金(20105314110006) |
| |
| 摘 要： | 为了提高数字图像相关曲面拟合法亚像素定位精度，经研究发现，在实际应用中，曲面拟合法在亚像素位移为0.5像素左右时会发生较大的波动，与实际亚像素位移发生一定偏离，导致此位置位移的不连续。本文通过分析曲面拟合法亚像素位移偏离真实位移的原因,给出了具体修正方法，用模拟平移实验讨论了修正系数k和子区大小对修正结果的影响，用三点弯曲实验验证了修正方法在复杂变形情况下的有效性，提高了曲面拟合法在实际应用中的测量精度。
|
| 关 键 词： | 图像处理 数字图像相关 曲面拟合 相关系数修正 亚像素 |
| 修稿时间： | 5/7/2013 12:00:00 AM |
Experimental Study of Correction Algorithm for Quadratic Surface Fitting in Digital Image Correlation |
| |
| YU Hai,GUO Rong-xin,XIA Hai-ting,YAN Feng,ZHANG Yu-bo and HE Tian-chun.Experimental Study of Correction Algorithm for Quadratic Surface Fitting in Digital Image Correlation[J].Journal of Experimental Mechanics,2013,28(5):586-594. |
| |
| Authors: | YU Hai GUO Rong-xin XIA Hai-ting YAN Feng ZHANG Yu-bo and HE Tian-chun |
| |
| Institution: | Department of Engineering Mechanics,Kunming University of Science and Technology,Key Laboratory of Yunnan Higher Education Institutes for Mechanical Behavior and Microstructure Design of Advanced Materials, Kunming 650500, China;Department of Engineering Mechanics,Kunming University of Science and Technology,Key Laboratory of Yunnan Higher Education Institutes for Mechanical Behavior and Microstructure Design of Advanced Materials, Kunming 650500, China;Department of Engineering Mechanics,Kunming University of Science and Technology,Key Laboratory of Yunnan Higher Education Institutes for Mechanical Behavior and Microstructure Design of Advanced Materials, Kunming 650500, China;Department of Engineering Mechanics,Kunming University of Science and Technology,Key Laboratory of Yunnan Higher Education Institutes for Mechanical Behavior and Microstructure Design of Advanced Materials, Kunming 650500, China;Department of Engineering Mechanics,Kunming University of Science and Technology,Key Laboratory of Yunnan Higher Education Institutes for Mechanical Behavior and Microstructure Design of Advanced Materials, Kunming 650500, China;Yunnan University, Kunming 650500, China |
| |
| Abstract: | In order to improve subpixel positioning accuracy of quadratic surface fitting in digital image correlation, it is found that large subpixel displacement fluctuation occurs round 0.5 pixels in practical application which leads to the deviation of calculation result from actual subpixel displacement and the displacement discontinuity at this position. A specific correction method is proposed in this paper by analyzing the cause of subpixel displacement deviation in surface fitting. The effects of correction factor k and sub-rigion size on the correction results were studied by simulation translation experiment. Correction method effectiveness in complex deformation was verified by three point bending experiment. Above results improve the measurement precision of curved surface fitting in practical application. |
| |
| Keywords: | image processing digital image correlation curved surface fitting correlation coefficient correction subpixel |
|
| 点击此处可从《实验力学》浏览原始摘要信息 |
| 点击此处可从《实验力学》下载免费的PDF全文 |
|
