首页 | 本学科首页   官方微博 | 高级检索  
     检索      

泡沫镍制备中化学镀镍研究
引用本文:李开华,罗江山,刘颖,唐永建.泡沫镍制备中化学镀镍研究[J].强激光与粒子束,2007,19(7):1158-1162.
作者姓名:李开华  罗江山  刘颖  唐永建
作者单位:1. 四川大学 材料科学与工程学院, 成都 610065;2. 中国工程物理研究院 激光聚变研究中心, 四川 绵阳 621900
基金项目:中国工程物理研究院高温高密度等离子体重点实验室基金
摘    要: 探讨了泡沫镍制备过程中,聚氨酯泡沫模板上的低温化学镀镍工艺,考察了镀液温度、pH值、主盐与还原剂浓度对沉积速率的影响。得出了适宜的工艺条件:硫酸镍30 g/L、次亚磷酸钠30 g/L、柠檬酸钠10 g/L、氯化铵30 g/L,镀液pH=9.0~9.5、温度45 ℃。在该工艺条件下,化学镀过程稳定,沉积速率可达40 mg/(cm3×h)。化学镀镍后经电镀、热解和还原退火处理制得泡沫镍,其样品呈3维网络状结构,密度为0.74 g/cm3,孔隙率为91.7%。

关 键 词:化学镀  泡沫镍  聚氨酯  沉积速率
文章编号:1001-4322(2007)07-1158-05
收稿时间:2006/10/30
修稿时间:2006-10-30

Electroless plating in synthesizing nickel foams
LI Kai-hua,LUO Jiang-shan,LIU Ying,TANG Yong-jian.Electroless plating in synthesizing nickel foams[J].High Power Laser and Particle Beams,2007,19(7):1158-1162.
Authors:LI Kai-hua  LUO Jiang-shan  LIU Ying  TANG Yong-jian
Institution:1. Department of Material Science and Engineering, Sichuan University, Chengdu 610065, China;2. Research Center of Laser Fusion, CAEP, P.O.Box 919-987, Mianyang 621900, China
Abstract:The technique of low-temperature electroless-plating nickel on the polyurethane foam in synthesizing nickel foams was investigated. The main factors affecting the deposition rate such as temperature, pH value, the concentration of nickle sulfate and reducing agent were explored. The obtained optimum process conditions are 30 g/L NiSO4, 30 g/L NaH2PO2, 10 g/L Na3C6O7H6, 30 g/L NH4Cl, 9.0~9.5 pH value at the reaction temperature of 45 ℃. In this technical condition, the process is stable with the deposition rate of 40 mg/(cm3·h). Nickel foams with a density of 0.74 g·cm-3 and a hole-rate of 91.7% was fabricated by electrodeposition, pyrogenation and deoxidization annealing after the electroless plating.
Keywords:Electroless plating nickel  Nickel foam  Polyurethane  Deposition rate
本文献已被 CNKI 维普 万方数据 等数据库收录!
点击此处可从《强激光与粒子束》浏览原始摘要信息
点击此处可从《强激光与粒子束》下载免费的PDF全文
设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号