面向传递路径分析方法研究的试验系统设计*

在传递路径分析理论研究中,经典传递路径分析要求在传递函数测量时拆卸激励源,为了减少工作量,设计一套面向传递路径分析方法研究的实验系统。以简化发动机模型作为激励源,真实汽车发动机悬置作为传递路径,简化车身内的响应为目标响应,建立一套完整的传递路径分析模型。在保留主要激励特征情况下简化发动机机体结构,将NI Compact RIO作为控制核心,激振器作为激励施加装置,以缸压信号和机体振动信号为激励信号对机体加载,实现发动机激励特征的模拟。最终验证该实验系统可模拟出发动机的结构噪声,采集信号中阶次成分明显,主要噪声频段基本吻合,可从阶次信号中提取对应转速信息。整个实验系统结构简单,可作为载体用于传递路径分析方法的研究。     

The Analysis and Improving of the Microwave Exciter in the Lower Hybrid Wave System

When we carry out lower hybrid wave heating and current driving plasma experiment at tokamak, we need mega-watt order of microwave power. The microwave signal at frequency of 2450 MHz is generated by a microwave exciter. According to the experiment＇s demands, the microwave exciter must provide output power of 1.5～ 2. 5 W with stabilized frequency and amplitude tobe used as the klystron input. Being amplified by the klystron, the microwave signal is transmitted through the transmitting system to the antenna and is emitted into the HL-2A tokamak. So we can see that the microwave exciter＇s function is very important to the lower hybrid wave heating and current driving plasma experiment.     

LHCD系统微波激励源性能优化设计

使用数字锁相环技术实现一定带宽内高精度可调节的频率输出,解决了速调管长期工作后响应频率发生偏移,模拟锁相环无法工作在系统最佳频率的问题;在移相器后增加功率幅度控制电路,保证了线性放大器的输出功率不会受到相位调节的影响;设计了一种基于数模转换(D/A)技术与微波电调技术相结合的波形控制单元,解决了激励源输出波形不可控的问题。通过以上三方面的改进,完成了HL-2M装置LHCD系统微波激励源的性能优化设计。     

The Design of the Microwave Exciter for Klystron

To carry out lower hybrid wave heating and current drive plasma experiment on tokamak, we need mega-watt order of microwave power generated by the parallel-running klystrons. Those klystrons must be driven by the microwave exciter. Now our microwave exciter is used for many years and its performance is decreased very much. It can not satisfy any more the hybrid wave heating and current drive plasma experiment. So we set out to design a new microwave exciter that is consist of the microwave solid components, amplitudestabilization control, modularization design with multitude-outputs, microwave phase control in order to satisfy the demand of the different work in the hybrid wave heating and current drive plasma experiment.     

全固态激励小型TEA CO_2激光器的研制

基于国产非晶态合金磁芯,研制了采用可控硅开关、脉冲升压变压器、以及两级磁脉冲压缩网络的全固态激励电路系统,并且应用于放电体积为29 cm3,工作气压为100 kPa的电晕预电离小型TEA CO2激光器。讨论了提高系统能量传输效率和减小系统体积的设计方法,并且测量了系统的工作性能以及各部分的能量损失。实验结果表明:磁脉冲压缩网络的能量传输效率大于83%,全固态激励系统的总效率大于75%;连接激光器负载时,输出脉冲的电压峰值约为22 kV,电流上升时间约为100 ns;得到了脉冲能量109 mJ,宽度70ns的激光输出,激光器整体效率约为3.3%。在目前的封离体积与气体循环方式限制下,激光器最大重复频率约为100 Hz,而激励电路部分可以达到400 Hz的工作频率。     

电磁力控制的主动减振实验

用传递函数法对受随机激励的结构作主动减振设计时所获得的反馈,本文以电磁激振器作为控制器进行主动减振实验,试验在受低频正弦和宽带随机两种激励的四自由度汽车模型上进行。结果表明,电磁激振器作为控制器具有很小的机械滞后特性,适用于作低频、宽带的随机振动主动减振,减振效果达到80%以上。     

基于ARM Cortex-M3微控制器与QDUC的嵌入式激励器设计

为解决传统激励器设备体积大、成本高等问题,采用ARM Cortex-M3微控制器与QDUC方案设计了一种嵌入式激励器;系统基于ARM Cortex-M3微控制器、以太网PHY与uIP TCP/IP协议栈构建有线以太网实现与外部上位机之间的数据的收发,使用专用QDUC集成电路芯片对以太网传送来的基带数据进行正交数字上变频,产生任意波形射频激励信号。该方案具有环境适应性强、尺寸小、结构简明、开发难度低、工作稳定可靠、可扩展性强等特点。试验实测系统工作于UDP模式时最大可用基带数据更新速率可达21.5Mbps,输出射频信号载波频率覆盖DC～400MHz,满足实际工程需求。     

Experiment of active control using electromagnetic force

In the use of the feedback designed by the transfer function method, the experiment on active control, in which an electromagnetic exciter is used as an actuator, is studied in this paper. The experiment has been made using a car model with four degrees of freedom (4 DOF) excited by low frequency sine or wider bandwidth random signal. This shows that the electromagnetic exciter is suitable for active control in the case of low frequency and wider bandwidth random signal because of its short mechanical delay, and the attenuating effect is above 80%.The project was supported by National Natural Science Foundation of China.     

HL-2Mװ��LHCDϵͳ3.7GHz΢������Դ���

介绍了HL-2M装置低混杂波系统中3.7GHz微波激励源的设计。微波激励源设计为模块化形式,由3.7GHz点频固态源单元、功率分配器单元、功率放大器单元和现场控制器单元等组成。微波激励源有8路输出端口,每个端口的输出功率在0~10W范围内连续可调,并可以实现远程控制输出功率;采用取样鉴相锁相环技术使微波输出信号具有相位噪声低、频率稳定度高、杂散抑制好等优点。频偏1kHz时,相位噪声是-115dBc/Hz,频偏10kHz时,相位噪声是-117dBc/Hz,频偏100kHz时,相位噪声是-122dBc/Hz;输出频率稳定度≤0.03ppm/30min;杂散抑制≤-80dBc。     

小型大功率脉冲半导体激光器的激励器设计

介绍以WMOS管作开关管的小型大功率脉冲半导体激光器的激励器原理,提出模块化激励器的设计观点,并给出实例。