一种通过梯形PPMgLN波导倍频实现带宽可调谐光源的理论研究

本文设计了一种梯形的周期极化掺镁铌酸锂(PPMgLN)波导,并通过在传播方向上引入温度梯度来拓宽其倍频(SHG)过程的泵浦光源可接收带宽。通过有限差分的光束传输法,计算波导的有效折射率,并进行波导尺寸的设计。结果表明,通过改变梯形波导不同位置的温度,使其形成一个温度梯度,可拓宽泵浦光源的波长可接收带宽。本文所设计的PPMgLN波导最大泵浦光源可接收带宽为C波段,即1 530~1 565 nm,该波导可倍频C波段,得到输出波段带宽为765~782.5 nm,温度调谐范围为30~150 ℃。     

石墨烯负载的氧配位钴单原子稳定金属锂负极

Lithium (Li)-based batteries are the dominant energy source for consumer electronics, grid storage, and electrified transportation. However, the development of batteries based on graphite anodes is hindered by their limited energy density. With its ultrahigh theoretical capacity (3860 mAh∙g⁻¹), low redox potential (−3.04 V), and satisfactorily low density (0.54 g∙cm⁻³), Li metal is the most promising anode for next-generation high-energy-density batteries. Unfortunately, the limited cycling life and safety issues raised by dendrite growth, unstable solid electrolyte interphase, and "dead Li" have inhibited their practical use. An effective strategy is to develop a suitable lithiophilic matrix for regulating initial Li nucleation behavior and controlling subsequent Li growth. Herein, single-atom cobalt coordinated to oxygen sites on graphene (Co-O-G SA) is demonstrated as a Li plating substrate to efficiently regulate Li metal nucleation and growth. Owing to its dense and more uniform lithiophilic sites than single-atom cobalt coordinated to nitrogen sites on graphene (Co-N-G SA), high electronic conductivity, and high specific surface area (519 m²∙g⁻¹), Co-O-G SA could significantly reduce the local current density and promote the reversibility of Li plating and stripping. As a result, the Co-O-G SA based Li anodes exhibited a high Coulombic efficiency of 99.9% at a current density of 1 mA∙cm⁻² with a capacity of 1 mAh∙cm⁻², and excellent rate capability (high current density of 8 mA∙cm⁻²). Even at a high plating capacity of 6 mAh∙cm⁻², the Co-O-G SA electrode could stably cycle for an ultralong lifespan of 1300 h. In the symmetric battery, the Co-O-G SA based Li anode (Co-O-G SA/Li) possessed a stable voltage profile of 18 mV for 780 h at 1 mA∙cm⁻², and even at a high current density of 3 mA∙cm⁻², its overpotential maintained a small hysteresis of approximately 24 mV for > 550 h. Density functional theory calculations showed that the surface of Co-O-G SA had a stronger interaction with Li atoms with a larger binding energy, −3.1 eV, than that of Co-N-G SA (−2.5 eV), leading to a uniform distribution of metallic Li on the Co-O-G SA surface. More importantly, when matched with a sulfur cathode, the resulting Co-O-G SA/lithium sulfur full batteries exhibited a high capacity of 1002 mAh∙g⁻¹, improved kinetics with a small polarization of 191 mV, and an ultralow capacity decay rate of 0.036% per cycle for 1000 cycles at 0.5C (1C = 1675 mA∙g⁻¹) with a steady Coulombic efficiency of nearly 100%. Therefore, this work provides novel insights into the coordination environment of single atoms for the chemistry of Li metal anodes for high-energy-density batteries.     

冷冻法硝酸磷肥工艺中酸不溶物提纯研究

采用酸浸、磁选酸浸、水淬/研磨酸浸等不同工艺对冷冻法硝酸磷肥生产工艺中的废渣-酸不溶物进行了提纯处理,利用X射线荧光光谱仪(XRF测试)对酸不溶物提纯前后各成分含量的变化进行了分析,从中得出了不同工艺流程对酸不溶物纯度的影响,最终确定了最佳的酸不溶物处理工艺.结果表明:在酸浸实验中,盐酸酸浸效果最佳,可将酸不溶物中SiO2纯度达到82.43;;在酸浸工艺前加入磁选、水淬、研磨的工序均可有效提升酸不溶物的提纯效果;冷冻法硝酸磷肥工艺中酸不溶物最佳的提纯工艺路线为:干燥、筛分、水洗、磁选、研磨、盐酸酸浸,处理后酸不溶物中SiO2纯度达到88.92;,符合微硅粉的生产要求.     

熔盐法合成钛酸锂钾片晶及形貌控制

在碳酸钾、碳酸锂和二氧化钛的混合原料中加入熔盐氯化钾,通过高温煅烧一步制备出钛酸锂钾片晶( K0.8 Li0.27Ti1.73O4, KLTO).通过控制熔盐的添加方式以及煅烧工艺(升温速率、煅烧时间)使材料的形貌朝着二维方向生长,并利用XRD和SEM等手段进行表征.分析发现:过快的升温速率或者较短的煅烧时间都会使材料朝三维方向生长成球状或者块状,反之则会使材料趋向一维方向生长成棒状;同时在煅烧温度达到一定值时再加入熔盐则更有利于片晶的生成.最终得到KLTO片状形貌的最佳控制工艺为:先以300 ℃/h升温至800 ℃后,再加入质量分数为40;的KCl熔盐,接着将升温速率变为200 ℃/h,加热至950 ℃,并在此温度下煅烧3 h.     

超导太赫兹天线耦合微测辐射热检测器

超导太赫兹天线耦合微测辐射热检测器具备探测频段宽、响应速度快、灵敏度高、易于阵列化等特点因而具备广阔的应用前景.本文的主要工作是设计并微纳加工出基于氮化铌薄膜的超导器件,针对所制备器件的关键参数进行了表征.测试结果显示,当浴冷温度为4K 时,器件响应时间为4μs,噪声等效功率达到30fW/Hz0.5.基于所制备的器件进行了陶瓷刀被动扫描成像实验并取得了良好的成像效果     

铜铁镁三掺铌酸锂晶体的第一性原理研究

利用基于密度泛函理论的第一性原理,研究了Cu:Fe:Mg:LiNbO3晶体及对比组的电子结构和光学特性.研究显示,单掺铜或铁铌酸锂晶体的杂质能级分别由Cu 3d轨道或Fe 3d轨道贡献,禁带宽度分别为3.45和3.42 eV;铜、铁共掺铌酸锂晶体杂质能级由Cu和Fe的3d轨道共同贡献,禁带宽度为3.24 eV,吸收峰分别在3.01,2.53和1.36 eV处;Cu:Fe:Mg:LiNbO3晶体中Mg^2+浓度低于阈值或高于阈值(阈值约为6.0 mol%)的禁带宽度分别为2.89 eV或3.30 eV,吸收峰分别位于2.45 eV,1.89 eV或2.89 eV,2.59 eV,2.24 eV.Mg^2+浓度高于阈值,会使吸收边较低于阈值情况红移;并使得部分Fe^3+占Nb位,引起晶体场改变,从而改变吸收峰位置和强度.双光存储应用中可选取2.9 eV作为擦除光,2.5 eV作为读取和写入光,选取Mg^2+浓度达到阈值的三掺晶体在增加动态范围和灵敏度等参量以及优化再现图像的质量等方面更具优势.     

复合酶耦合酶解酸处理后玉米秸秆的研究

以玉米秸秆为研究对象,经过2%硫酸预处理后,利用果胶酶、β-葡萄糖苷酶、纤维素酶三种酶协同酶解,以提高玉米秸秆的酶解产糖量。结果表明:当酶解时间为48h,果胶酶、β-葡萄糖苷酶、纤维素酶分别为45U/mL、30U/mL、60U/mL时,葡萄糖、木糖和酶水解得率分别为67.83%、3.25%、73.65%,相比纤维素酶单一酶解的葡萄糖、木糖和酶水解得率分别提高了65.04%、20.82%、65.06%。分步糖化发酵5天后,相比单一酶解发酵乙醇含量提高了72.5%。说明利用三种酶复合处理,能明显提高酶解产糖量。研究结果为玉米秸秆转化为可发酵糖技术的研究提供重要参考。     

50Hz铌酸锂电光调Q开关

目前军用领域电光调Q开关的工作频率基本在30 Hz以下,为满足军用领域对更高重复频率脉冲激光的需求,研究并获得了可工作在50 Hz重复频率下的铌酸锂电光调Q开关.基于折射率椭球理论,通过分析铌酸锂晶体预偏置电光调Q的原理,选取了合适的预偏置角度.在闪光灯泵浦Ce∶ Nd∶ YAG激光系统中,通过合理设计谐振腔参数以及激光晶体的参数,采用预偏置加压式电光调Q方式,实现了频率为50 Hz,脉宽约为6 ns,能量不小于93mJ的1.06 μm激光输出,峰值功率达到了约15 MW.试验证明铌酸锂晶体用作电光调Q开关在中小功率和中低频率1.06μm激光上有很好的应用前景.