重金属污染土壤植物修复的强化措施研究进展

植物修复是一种有着巨大市场潜力的治理重金属污染土壤的技术,由于影响植物修复效率的因素较多,至今实际应用还很少。针对目前植物修复技术的不足,主要从植物本身的性能、重金属的生物有效性以及农艺管理措施等三方面,综述了近年来国内外有关植物修复强化措施的研究进展,并展望了今后该领域的研究方向。     

核磁共振法研究CH2=CHSi（OET）3的水化反应

高强水泥的生产近年来巳成为许多国家发展水泥生产的一个主要方向。在水泥中加入有机单体可以改善混凝土的质量,如加重量比为3％的有机硅烷偶联剂乙烯基三乙氧基硅烷CH_2=CHSi(OEt)_3(简称VTES)于水泥中,即可在较大程度上增加水泥石的强度。     

两性淀粉接枝共聚物在中性抄纸中的应用

为考察两性淀粉与丙烯酰胺接枝共聚及阳离子合成的具有功能化、网络化的多元变性淀粉对纸张的增强效果,采用废纸浆为原料,在中性抄纸条件下,对该多元变性淀粉的增强应用性能进行了研究。结果发现,两性淀粉与丙烯酰胺接枝共聚物(AS-g-PAM)及其阳离子化的衍生物(AS-g-CPAM)比两性淀粉具有更好的增强效果,尤其可大幅度提高纸张的环压强度。与两性淀粉比较,用量为0.5%AS-g-PAM和AS-g-CPAM可分别提高环压指数22%和45%以上,对纸张的抗张指数、耐破度等也比使用两性淀粉有不同程度的提高,同时,AS-g-CPAM在0.05%的低用量时,仍具有较好的增强效果。     

Effect of transition elements on dispersoid formation and elevated-temperature mechanical properties in 6082 aluminum alloy

ABSTRACT

The effect of transition elements, specifically Mn, Cr, V, and Mo, on dispersoid formation and mechanical properties in 6082 aluminum alloy was studied. The elevated-temperature mechanical properties were evaluated based on the compressive yield strength and creep resistance. The results indicated that the addition of Mn to the 6082 alloy resulted in the formation of a large number of the thermally stable α-Al(MnFe)Si dispersoids, thereby significantly improving the elevated-temperature mechanical properties of the alloy. Subsequent additions of Cr, V, and Mo increased the amount of Mn-bearing intermetallic phases, which decreased the supersaturation levels of Mn and Si in the α-Al, and consequently decreased the volume fraction of the dispersoids. The alloys containing Cr, V, and Mo exhibited similar yield strengths at 300°C and higher yield strengths at room temperature compared to the alloy containing only Mn. The size effect of the smaller dispersoids containing Cr, V, and Mo together with the solid-solution hardening of these elements could balance out the strength decrease resulting from the decreased volume fraction of the dispersoids. The additions of Cr, V, and Mo significantly increased the creep resistance of the Mn-containing 6082 alloy. Vanadium induced the highest creep resistance followed by Cr and Mo. Solute atoms of these elements with low diffusivity in the aluminum matrix contributed significantly to increasing the creep resistance at 300°C.     

Theoretical Study on Hydrogen Bonding of Mono‐ and Dihydrated Complexes of 7‐(3′‐Pyridyl)indole in Excited States

The intermolecular hydrogen bonds of mono‐ and dihydrated complexes of 7‐(3′‐Pyridyl)indole (7‐3′PI) have been investigated using the time‐dependent density functional theory (TD‐DFT) method. The electrostatic potential analysis of monomer 7‐3′PI and 7‐(3′‐Pyridyl)indole‐water (7‐3′PI‐W) indicates that an intermolecular hydrogen bond between two waters can be formed for 7‐(3′‐Pyridyl)indole‐2water (7‐3′PI‐2W) complex. The calculated bond lengths of the intermolecular hydrogen bonds of 7‐3′PI‐W and 7‐3′PI‐2W in the S₁ state (the first excited singlet state) are all shortened compared to the ground state. By the analysis of bond length, charge population and infrared spectra, it is demonstrated that the intermolecular hydrogen bonds of 7‐3′PI‐W and 7‐3′PI‐2W are all strengthened upon electronic excitation to the S1 state. Moreover, the fluorescence of 7‐3′PI‐W and 7‐3′PI‐2W are all red‐shifted to larger wavelength compared to monomer 7‐3′PI. The red‐shift of fluorescence peak of 7‐3′PI‐W and 7‐3′PI‐2W should be attributed to the change of hydrogen bond interaction before and after photoexcitation. Therefore, it can be concluded that the intermolecular hydrogen bonding strengthening in the excited S₁ state induces the fluorescence weakening of 7‐3′PI.     

Analysis of interfacial thermal stresses for damaged structures: new theoretical model

The use of the composites for the reinforcement of the beams and structures metallic and non-metallic, is one of the recent methods of the rehabilitation by composites, what permits to replace the classic techniques of the assembly based on soldering, bonding, etc. But this technique gives stresses concentrations to the level of the zone of the assembly. The methods of rehabilitation by composites permit to prolong the life span of these structures under a reduced exploitation cost and with less pollution to the environment. In this article, an original survey on the stresses between the structure and the composite (fiber reinforced polymer [FRP]) was finalized, taking account, as well, of the mechanical and thermal loadings, as well as the effects of deformation shear lag. This originality puts in evidence a new theoretical model which takes into account the thermal effect of the stresses concentration that has not been treated seriously by the previous studies.     

Anchorage strength models for end-debonding predictions in RC beams strengthened with FRP composites

The increase in the flexural capacity of RC beams obtained by externally bonding FRP composites to their tension side is often limited by the premature and brittle debonding of the external reinforcement. An in-depth understanding of this complex failure mechanism, however, has not yet been achieved. With specific regard to end-debonding failure modes, extensive experimental observations reported in the literature highlight the important distinction, often neglected in strength models proposed by researchers, between the peel-off and rip-off end-debonding types of failure. The peel-off failure is generally characterized by a failure plane located within the first few millimetres of the concrete cover, whilst the rip-off failure penetrates deeper into the concrete cover and propagates along the tensile steel reinforcement. A new rip-off strength model is described in this paper. The model proposed is based on the Chen and Teng peel-off model and relies upon additional theoretical considerations. The influence of the amount of the internal tensile steel reinforcement and the effective anchorage length of FRP are considered and discussed. The validity of the new model is analyzed further through comparisons with test results, findings of a numerical investigation, and a parametric study. The new rip-off strength model is assessed against a database comprising results from 62 beams tested by various researchers and is shown to yield less conservative results. Russian translation published in Mekhanika Kompozitnykh Materialov, Vol. 44, No. 3, pp. 373–388, May–June, 2008.     

K9光学玻璃化学钢化技术研究

为提高K9光学玻璃在一些特殊应用领域（如高压、温度变化剧烈等）的力学性能,并保证其光学性能符合精密光学仪器要求,对K9光学玻璃进行了化学钢化技术研究。以脆性材料断裂过程微裂纹扩展理论为基础,导出化学钢化玻璃强度应力因子计算模型,分析化学钢化表面应力与表面微裂纹深度、韧性之间的关系,指出化学钢化工艺应注意的事项。通过实验研究,分析化学钢化温度和钢化时间对K9光学玻璃抗弯强度、表面应力及应力层厚度的影响,优化得出K9光学玻璃化学钢化温度为400 ℃、钢化时间为40 h。采用优化工艺,获得了表面应力为500 MPa、应力层厚度为50 μm量级及规格为220 mm×110 mm×22 mm的化学钢化K9光学玻璃样件。钢化后,样件抗弯强度提高了3.5倍以上,且表面疵病、光学鉴别率、透过率等光学性能指标未见明显变化。     

The elastic fields of misfit cylindrical particles: a dislocation-based numerical approach

Analytical solutions for the displacement and stress fields due to a misfit particle in a host matrix can be difficult to obtain, especially for complex particle geometries. In this work, we present a numerical method for finding such fields in the case of infinitely-long particles. The method is based on discretizing the continuous misfit region between the particle and matrix into local misfit regions consisting of interstitial dislocation loops. The results presented here indicate very good agreement with analytical solutions and better convergence with increasing loop density.     

A method for predicting the deflection of reinforced concrete beams strengthened with carbon plates

For strengthening bent beams, plates of reinforced plastics are glued to their tensioned surface. As s result, the beam becomes layered, and it is possible to control its rigidity and deflection. Based on the methods of structural mechanics of layered media, a method is elaborated for determining the deflection of such beams on the entire range of loading up to their ultimate failure. A comparison between the theoretical and experimental results is carried out. __________ Translated from Mekhanika Kompozitnykh Materialov, Vol. 42, No. 1, pp. 45–60, January–February, 2006.