The reference shrinkage curve of clay soil

The objective of this work is to develop and validate a model that predicts the reference soil shrinkage curve, that is one without crack volume contribution, as a necessary preliminary step in future estimation of soil crack volume from soil shrinkage data. Current soil shrinkage models are based on the approximation of soil shrinkage data by some a priori taken mathematical expressions and justified by the fitting of their parameters to the data. However, the crack volume entering the data is not single valued and depends on shrinkage conditions. Unlike that the reference shrinkage curve is single valued. For soils with sufficiently high clay content when there are no large pores (lacunar pores) inside the intra-aggregate clay, the reference shrinkage curve is derived from the assumption of the rigid superficial (interface) layer of aggregates with changed pore-size range and distribution compared with the intra-aggregate matrix. This consideration is based on accounting for contributions of the interface aggregate layer and intra-aggregate matrix to the soil volume and water content during shrinkage. The reference shrinkage curve is predicted by eight fundamental physical immediately measured parameters of (i) the intra-aggregate matrix (including clay content); (ii) the aggregate structure; and (iii) the mean silt-sand grain size or mean interface layer thickness. The model was validated using the data for eight soils. In addition to the major potential application for estimating a soil crack volume, the model explains differences between the observed shrinkage curves of soil and pure clay, and it can have other numerous applications.     

ABS注塑制品的模内蠕变试验研究

不同于传统的热残余应力分析,本文着眼于注塑制品的模内蠕变研究。通过测试ABS注塑薄板在不同工艺条件下的收缩变形,比较基于弹性理论的热收缩,进而得到了模内蠕变量。分析结果表明,模内蠕变对于降低制品最终的收缩变形起着重要的作用。在研究了各种工艺条件对制件模内蠕变的影响后,发现较低的模腔表面温度或较长的成型周期会导致蠕变增大,而制件在模内的蠕变(或应力松弛)主要发生在固化后的高温区。本文同时探讨了保压压力对蠕变的影响。高注塑保压压力通常会减小注塑件的收缩,但同时会减小制件模内蠕变。     

关于孔隙压力系数

在提出剪缩系数概念和修正体积压缩系数概念的基础上,导出了两种轴对称应力状态和一般三向应力状态下孔隙 压力增量与主应力增量关系的理论公式,给出了这三种应力状态下孔隙压力系数的表达式,对这三种应力状态下孔隙压力系 数的关系和变化规律进行了分析,提出了孔隙压力增量与主应力增量关系表达形式的建议。     

水硬性石灰合成及拉破坏特性试验研究

水硬性石灰在欧洲石质文物修复和加固中获得了很大成功。我国的石质文物主要是砂岩,水硬性石灰的修复效果不好。为满足我国石质文物修复和加固的需求,本文以石灰石和黏土为原料,在950℃煅烧不同时间,制备出水硬性石,对试样的成分、微观形貌、收缩率、抗拉强度和拉破坏过程等进行了研究。结果表明:(1)试样中含有水硬性成分2CaO·SiO2(C2S);煅烧8h时,成分与欧洲水硬性石灰NHL5接近;1.5CaO·SiO2·xH2O(C-S-H)和CaCO3的含量随龄期的增加逐渐增加。(2)龄期1~3d,收缩率较小;龄期4~6d,收缩率以线性规律增加;7d以后,收缩率趋于稳定。(3)局部变形区随拉应力的增加而变大,邻近局部变形区逐渐合并,形成面积更大的应变局部化带;载荷超过峰值后,产生微裂隙;随载荷进一步增加,微裂隙扩展,贯穿整个试件,发展成宏观裂隙,使试件破坏。(4)抗拉强度随龄期的增加而增加,水硬性石灰中C-S-H、CaCO3等相互交织,构成空间致密体,使试件力学强度提高。合成的水硬性石灰物理力学性能与欧洲水硬性石灰NHL5相近,并且成分均匀、可控,在石质文物修复和加固工程中具有良好应用前景。     

考虑收缩徐变影响的新旧混凝土叠合梁单元刚度矩阵改进

混凝土自身的收缩徐变会在新旧混凝土叠合梁中使应力重分布.为了计算重分布应力,首先推导以挠度表达的叠合梁非线性微分方程,然后通过求解该微分方程,引入位移形函数、刚度形函数和等效节点载荷形函数,最后得出新混凝土梁、旧混凝土梁和Goodman弹性夹层三合一的叠合梁改进型单元刚度矩阵和等效节点载荷,从而为收缩徐变影响下的混凝土的内力计算提供了一种有效的新方法.文中还进行了实例验证分析,并从中得出了一些有益的结论.     

Effect of Injection Parameters and Addition of Nanoscale Materials on the Shrinkage of Polypropylene Copolymer

The effect of variation of injection conditions and addition of nano-calcium carbonate (CaCO₃), nano-silicon dioxide (SiO₂) and full-vulcanized nano-powdered styrene butadiene rubber (PSBR) on the shrinkage of injection-molded polypropylene-ethylene copolymer (90/10, co-PP) were investigated. The results showed that the shrinkage was different for different locations along the flow path. The shrinkage in the length direction of the injection-molded sample varied with the adjustment of the processing parameters, while the shrinkage in the width and thickness direction was almost unchanged. The addition of nano-CaCO₃ and PSBR decreased the shrinkage of co-PP, while the shrinkage of co-PP/ SiO₂ composite was almost unchanged.     

The influence of Au-nanoparticles presence in PDMS on microstructures creation by ion beam lithography

3D microstructures in pure poly(dimethylsiloxane) (PDMS) and PDMS with embedded Au nanoparticles were prepared by ion beam lithography without any further etching. Two mega-electron volts helium and 10 MeV oxygen ions were used for ion microstructuring. Parallel lines of 1 mm in length and 10 μm in thickness were fabricated for investigation of the effect of the nanoparticles presence in the polymer on the surface morphology of the created microstructures. The created microstructures were checked by optical microscope. Infrared (IR) spectrometry was used to study the effect of the ions type and fluence on the chemical changes of the material. Atomic force microscopy was used for the fine detail study as well as for checking the microstructure quality. Analysis revealed an increased radiation resistance of the nanocomposite compared to the pure PDMS. Shrinkage is proportional to the fluence, but the maximum value for both materials is limited by saturation. 3D microstructure in modified PDMS obtained at the same irradiation condition as pure PDMS is characterized by its smaller height. Obtaining the microstructure in nanocomposite of the same height as in pure PDMS by increasing the fluence can be impossible due to saturation of shrinkage and/or radiation-induced heating of the material.     

Local shrinkage and stress induced by thermo-oxidation in composite materials at high temperatures

The paper is concerned with the modelling, simulation and experimental characterisation of local shrinkage strains and stresses induced by thermo-oxidation phenomena in the IM7/977-2 carbon/epoxy composite material at elevated temperatures. The oxygen concentration and mechanical fields were established through a coupled model constructed from a unified multiphysical approach and the thermodynamics of irreversible processes. The model was implemented in the ABAQUS^® finite element commercial code. Simulations of thermo-oxidation-induced matrix shrinkage were run at a local scale, i.e., the scale of the elementary constituents of the composite, the fibre and the matrix. The experimental assessment was done at the same scale, and the local matrix shrinkage profiles were measured by confocal interferometric microscopy.A good agreement was found between the simulated and measured profiles, validating the unified model. The thermo-oxidation induced stress field was analysed to understand the influence of the environment on the onset of damage in composite materials at elevated temperature.     

Why Matter Occupies so Large a Volume？

The paper represents a rigorous treatment of the underlying quantum theory, not just in words but providing the underlying technical details, as to why matter occupies so large a volume and its intimate connection with the Pauli exclusion principle, as more and more matter is put together, as well as of the contraction or shrinkage of ＂bosonic matter＂, upon collapse, for which the Panli exclusion is abolished. From the derived explicit bounds of integrals of powers of the particle number densities, explicit bounds on probabilities of the occurrences of the events just described are extracted. These probabilities lead one to infer the change of the ＂size＂ or extension of such matter, upon expansion or contraction, respectively, as their content is increased.     

基于遗传算法和神经网络的注塑工艺参数优化

基于Moldflow模拟仿真的结果,结合GA算法优化BP网络的结构,建立了模具温度,熔体温度,保压压力,注射速度等工艺参数与塑件体积收缩率的BP网络模型.获得了最优的工艺参数组合,同时预测结果与实际结果吻合.通过神经网络算法(BP)预测注塑工艺参数对塑件质量的影响,可以有效降低其他建模方法的难度和工作量,方法可以推广到塑件其他质量预测过程中.