基于Rietveld精修方法解析Bi2O3的原子热振动

三氧化二铋(Bi₂O₃)是氧离子导电体,为了获得它的原子热振动各向同性温度因子,对该粉末晶体进行X射线衍射实验,建立了晶体结构模型,利用Rietveld 精修方法的RIETAN-2000 程序对所得实验结果进行了晶体结构精修,通过最大熵方法(MEM)解析得到了粉末晶体的等高电子密度分布三维(3D) 和二维(2D)可视化图谱。结果表明,各原子Bi₍₁₎、Bi₍₂₎、O₍₁₎、O₍₂₎和O₍₃₎的原子热振动各向同性温度因子分别为0.004 938 nm²、0.004 174 nm²、0.007 344 nm²、0.007 462 nm²、和0.007 857 nm²,等高电子密度分布的可视化,进一步验证了晶体结构模型和原子位置的准确性,这些参数对研究晶体材料的热性质具有一定参考意义。     

Negative thermal expansion in NbF_3 and NbOF_2:A comparative theoretical study

Thermal expansion control is always an obstructive factor and challenging in high precision engineering field. Here,the negative thermal expansion of Nb F_3 and Nb OF_2 was predicted by first-principles calculation with density functional theory and the quasi-harmonic approximation(QHA). We studied the total charge density, thermal vibration, and lattice dynamic to investigate the thermal expansion mechanism. We found that the presence of O induced the relatively strong covalent bond in Nb OF_2, thus weakening the transverse vibration of F and O in Nb OF_2, compared with the case of Nb F_3.In this study, we proposed a way to tailor negative thermal expansion of metal fluorides by introducing the oxygen atoms.The present work not only predicts two NTE compounds, but also provides an insight on thermal expansion control by designing chemical bond type.     

Application of microcrystalline cellulose as an efficient and cheap sorbent for the extraction of metoprolol from plasma and wastewater before HPLC–MS/MS determination

A dispersive solid-phase extraction method based on a new sorbent has been performed on plasma and wastewater samples to determine metoprolol by high-performance liquid chromatography–tandem mass spectrometry. In this study, the analyte was adsorbed from the samples onto microcrystalline cellulose as a green and efficient sorbent and then eluted for use in the determination step. In the mass spectrometer, the analyte was detected in the positive mode and selectivity of the analysis was increased by sequential mass analysis through multiple reaction monitoring. All of the effective parameters in the extraction of metoprolol from plasma and wastewater were optimized. Under optimal conditions the method was linear in the ranges of 1–1,000 and 0.1–1,000 ng/ml in plasma and wastewater samples, respectively. The detection limits of the method were 0.30 and 0.03 ng/ml in plasma and wastewater samples, respectively. The data showed that the method provides low detection limit, wide linear range, good precision and high extraction recovery. Finally several plasma and wastewater samples were successfully analyzed using the method. The use of a small amount of a green and inexpensive sorbent and a low volume of plasma without the need for further pretreatment steps are the main advantages of the method.     

基于2,5-二溴对苯二甲酸配体的锌/钴配合物合成、晶体结构及性质

将有机物2,5-二溴对苯二甲酸(H₂L₁)和2,2′-联吡啶(L₂)作为双配体,使用溶剂热法和七水合硫酸锌(ZnSO₄·7H₂O)、六水合硝酸钴(Co(NO₃)₂·6H₂O)分别反应,得到配合物[Zn(L₁)(L₂)(H₂O)]_n(1)和配合物[Co(L₁)(L₂)(H₂O)]_n(2)。采用单晶X射线衍射、元素分析、红外光谱、紫外光谱、荧光光谱、热重分析等测试方法对这两种物质进行分析研究。单晶测试结果表明配合物1是单斜晶系,以Zn²⁺配位连接L^2-₁与L₂形成一维链状结构,各条链在分子间氢键和π…π共轭作用下有规律地堆叠形成三维网络结构。配合物2是三斜晶系,Co1离子和Co1ⁱ离子由H₂L₁上的羧酸氧原子O4和O4ⁱ连接,形成双齿螯合的配位结构单元,以Co²⁺配位连接 L^2-₁和L₂形成二维网格结构,各层在O—H…O分子间氢键和范德瓦耳斯力作用下有规律的堆叠形成三维网络结构。配合物1和2均含有芳香杂环、羧基杂环和氮杂环,具有良好的荧光性质和热稳定性,最大发射波长分别为345 nm和333 nm。     

金刚石衬底上GaN HEMT沟道温度建模:各向异性且非均匀热导率的影响

为了改善GaN HEMT的自热效应,集成高热导率的金刚石衬底有助于增强器件有源区的热量耗散。然而,化学气相淀积(CVD)生长的多晶金刚石(PCD)具有柱状晶粒结构,导致了各向异性的材料热导率,且其热导率值与生长厚度有关。为此,通过建模金刚石生长过程中晶粒尺寸的演变过程,计算了金刚石沿面内和截面方向的热导率。基于该PCD热导率模型,利用计入材料非线性热导率的GaN器件热阻解析模型,计算得到了GaN HEMT沟道温度的波动范围,并分析了其与器件结构(栅长、栅宽、栅间距、衬底厚度)和功耗的依赖关系。最后,通过与有限元(FEM)仿真结果对比,分区域提取了GaN HEMT器件中PCD衬底的有效热导率,分别为260~310 W/(m·K)和1 250~1 450 W/(m·K)。本文的计算为预测金刚石衬底上GaN HEMT器件的沟道温度提供了快速、有效的方法。     

基于抛光基材的热蒸镀铜箔生长高平整单层石墨烯薄膜

在石墨烯的化学气相沉积工艺中,铜箔是决定石墨烯薄膜质量的重要因素。传统铜箔由于制备工艺的限制,存在大量的缺陷,导致石墨烯薄膜的成核密度较高。本工作选用抛光铝板、抛光不锈钢板、微晶玻璃和SiO₂/Si作为基材,用热蒸镀法制备了不同粗糙度的铜箔,并详细讨论了以该系列铜箔生长高平整度石墨烯薄膜的条件及铜箔对石墨烯薄膜品质的影响。实验结果表明,铜箔以(111)取向为主,与基材分离后,表面具有纳米级平整度。在生长石墨烯后,从SiO₂/Si剥离的铜箔成核密度是4种基材中最小的。同时,从SiO₂/Si剥离的铜箔晶体结构变化最不明显,具有良好的结晶性,表面几乎不存在铜晶界缺陷。当压强为3 000 Pa,氢气和甲烷流速分别为300 mL/min和0.5 mL/min时,可以获得约1 mm横向尺寸的石墨烯单晶晶畴。     

射频等离子制备石墨烯负载Co3O4催化剂及其析氧性能研究

氢能的引入能有效提升配电网的供电可靠性,而电解水制氢是实现低碳转型的关键技术,开发高效的电解水催化剂势在必行。过渡金属氧化物储量大、催化活性高,是具有广阔应用前景的析氧反应催化剂。本文通过射频等离子体处理制备石墨烯上负载Co₃O₄析氧催化剂,XRD、Raman和XPS测试结果显示,二维结构石墨烯的引入加速表面电子迁移,增大了反应面积。等离子体处理促进了纳米粒子在石墨烯上的负载,利用等离子体刻蚀作用在催化剂表面制造出大量碳结构缺陷和氧空位结构,改善了活性位点分布,有效调控Co₃O₄电子结构,提高析氧催化活性。电化学测试表明,本文中合成的Co₃O₄@rGO在电流密度为50 mA·cm^-2时的过电位为410 mV,动力学反应速率较快,表现出优于商业IrO₂的析氧催化活性。     

Anti-fibrosis attributes: UHPLC-MS/MS-based pharmacokinetics profiling of a novel autotaxin inhibitor with excellent in vivo efficacy in rat

3,4-Difluorobenzyl(1-ethyl-5-(4-((4-hydroxypiperidin-1-yl)-methyl)thiazol-2-yl)-1H-indol-3-yl)carbamate (NAI59), a small molecule with outstanding therapeutic effectiveness to anti-pulmonary fibrosis, was developed as an autotaxin inhibitor candidate compound. To evaluate the pharmacokinetics and plasma protein binding of NAI59, a UPLC–MS/MS method was developed to quantify NAI59 in plasma and phosphate-buffered saline. The calibration curve linearity ranged from 9.95 to 1990.00 ng/mL in plasma. The accuracy was −6.8 to 5.9%, and the intra- and inter-day precision was within 15%. The matrix effect and recovery, as well as dilution integrity, were within the criteria. The chromatographic and mass spectrometric conditions were also feasible to determine phosphate-buffered saline samples, and it has been proved that this method exhibits good precision and accuracy in the range of 9.95–497.50 ng/mL in phosphate-buffered saline. This study is the first to determine the pharmacokinetics, absolute bioavailability, and plasma protein binding of NAI59 in rats using this established method. Therefore, the pharmacokinetic profiles of NAI59 showed a dose-dependent relationship after oral administration, and the absolute bioavailability in rats was 6.3%. In addition, the results of protein binding showed that the combining capacity of NAI59 with plasma protein attained 90% and increased with the increase in drug concentration.     

Processing of lignocellulosic polymer wastes using microwave irradiation

Lignin and mixed lignocellulosic natural polymer wastes have been accumulated in landfills over the past hundred years. These wastes should be processed to produce added- value chemicals and materials. This mini-review presents a brief literature survey related to state-of-the-art methods developed recently by the world research community to solve the problem of rational conversion of lignocellulosic polymer wastes, including production of hydrogen, synthesis gas, phenols, and monomers. The focus is made on microwave and plasma technologies used for lignocellulosic wastes processing.