Sample preparation procedure for the determination of sulphur and trace metals in oil products by the ICP with a minitorch using emulsions

A quick sample preparation method was used for the determination of sulphur and trace metals in oil and oily products by the ICP with a minitorch. Stable aqueous emulsions of oils and oil products were made by using two kinds of emulsifiers (one with low sulphur content, the other sulfonated). Aqueous standard solutions can be used for the preparation of calibration solutions. The contents of S, Al, Cr, Cu, Fe, Mg, Ni and Pb in aqueous emulsions were determined and the results were in good agreement with the composition of oil standard solutions used for control analysis procedure.     

Structural properties of charged diblock copolymer solutions

Aqueous micellar solutions of ionic/neutral block copolymers have been studied by light scattering, small angle neutron scattering and small angle X-ray scattering. We made use of a polymer comprised of a short hydrophobic block (polyethylene-propylene) PEP and of a long polyelectrolytic block (polystyrene-sulfonate) PSSNa which has been shown previously to micellize in water. The apparent polydispersity of these micelles is studied in detail, showing the existence of a few large aggregates coexisting with the population of micelles. Solutions of micelles are found to order above some threshold in polymer concentration. The order is liquid-like, as demonstrated by the evolution with concentration of the peak observed in the structure factor (), and the degree of order is found to be identical over a large range of concentrations (up to 20 wt%). Consistent values of the aggregation number of the micelles are found by independent methods. The effect of salt addition on the order is found to be weak. Received: 19 June 1997 / Received in final form: 4 September 1997 / Accepted: 9 October 1997     

Analysis of dielectric relaxations of w/o emulsions in the light of theories of interfacial polarization

An attempt is made to apply dielectric theories of interfacial polarization to observations of dielectric relaxations for W/O emulsions. Approximate formulas for disperse systems in a W/O type were derived from the two theories: one proposed by Maxwell and Wagner for dilute disperse systems of spherical particles, and the other developed by Hanai for concentrated disperse systems. Dielectric measurements were carried out on concentrated W/O emulsions prepared from kerosene and distilled water or KCl aqueous solutions by minimal use of emulsifiers. Marked dielectric relaxations were observed with the emulsions, the dielectric parameters having been determined to characterize the relaxation data. Phase parameters such as relative permittivity, electric conductivity and volume fraction of the disperse phase were evaluated from the dielectric parameters by use of the approximate formulas of the respective theories. The phase parameters evaluated and the frequency dependence of complex permittivity of the W/O emulsions deduced from the theory for concentrated disperse systems are in excellent agreement with the observed data in comparison to that for dilute disperse systems. It is concluded that the dielectric relaxations due to the interfacial polarization of disperse systems of spheres are explained satisfactorily by the theory for concentrated disperse systems.     

Determination of propazine by differential pulse polarography in micellar and emulsified media

An electroanalytical study of the herbicide propazine's reduction process in micellar solutions and oil-in-water emulsions is reported. The anionic surfactant sodium pentanesulphonate was chosen as the most suitable. The differential pulse polarograms of micellar solutions had two reduction peaks below pH 2.0, whereas only one peak was obtained above pH 2.O. Ethyl acetate was chosen as the organic solvent to form propazine emulsions. Unlike in micellar solutions, the DPP polarograms of propazine emulsions showed only one peak even at pH < 2.0, suggesting that propazine hydrolysis was hindered in the emulsified medium. The limiting current is diffusion-controlled and the electrode process is irreversible. Propazine can be determined by differential pulse polarography over the 1.0 × 10^–1 – 1.0 × 10^–1moll^–1 and 1.0 × 10^–15 – 4.0 × 10^–1 moll^–1 concentration ranges and the limit of detection was 2.8 × 10^–1 moll^–1. Of the potential interferents simazine, methoprotryne and terbutryn (alls-triazines), thiram (a dithiocarbamate), dinoseb (nitrophenolic), and heptachlor (chlorinated cyclo-diene herbicide), only the first two were significant (10% error for equimolar concentrations). The method was applied to the determination of propazine in spiked drinking water. At a concentration level of 2.0 × 10^–1 moll^–1 a recovery of 94 ± 6% was obtained, after tenfold concentration on Sep-Pak.     

A differential microcalorimetric study of whey proteins and their behaviour in oil-in-water emulsions

Oil-in-water emulsions (20% soya oil, 1% protein) have been prepared containing lysozyme or isolates of -lactalbumin and β-lactoglobulin from whey protein. The structural characteristics of these proteins adsorbed at an oil/water interface were determined by following their thermal transitions using differential scanning microcalorimetry. Thermograms of the proteins in the adsorbed state differed markedly from the corresponding transitions seen for the proteins in solution. This suggests that the proteins underwent substantial changes in secondary and tertiary structure upon adsorption. In general, for all the proteins studied, a net decrease in the total energy absorbed during denaturation was found when the proteins were in an adsorbed state. Both lysozyme and -lactalbumin were in part “surface denatured”, and they showed a certain degree of reversibility between solution and the adsorbed state. β-Lactoglobulin showed the highest degree of denaturation upon adsorption and the conformational change was irreversible.     

硅氧烷乳液聚合过程中大颗粒形成机理研究：Ⅰ.阳离子型乳液的耐电解质…

探讨了二甲基聚硅氧烷阳离子型乳液耐电解质稳定性的影响因素。结果表明，加入少量的非离子型表面活性剂与阳离子型乳化剂并用进行乳液聚合，可以保护乳液粒子，防止由于电解质引的乳液粒子的相互凝聚而形成大颗粒。     

Use of cetyltrimethylammonium bromide as surfactant for the determination of copper and chromium in gasoline emulsions by electrothermal atomic absorption spectrometry

In this work, the use of cetyltrimethylammonium bromide as surfactant for the preparation of oil-in-water emulsions for the determination of Cu and Cr in gasoline by electrothermal atomic absorption spectrometry (ET AAS) was evaluated. The surfactant amount was tested in the range of 25 to 300 mg, added to 2 ml of gasoline, and completed to 10 mL with 0.1% (v/v) nitric acid solution. 150 mg of surfactant was found optimum, and a sonication time of 10 min sufficient to form an oil-in-water emulsion that was stable for several hours. The ET AAS temperature program was established based on pyrolysis and atomization curves. The pyrolysis temperatures were set at 700 and 1300 °C for Cu and Cr, respectively and the selected atomization temperatures were 2400 and 2500 °C. The time and temperature of the drying stage and the atomization time were experimentally tested to provide optimum conditions. The limits of detection were found to be 5 μg L^− 1 and 1.5 μg L^− 1 for Cu and Cr, respectively in the original gasoline samples. The relative standard deviation (RSD) ranged from 4 to 9% in oil-in-water emulsions spiked with 5 μg L^− 1 and 15 μg L^− 1 of each metal, respectively. Recoveries varied from 90 to 98%. The accuracy of the proposed method was tested by an alternate procedure using complete evaporation of the gasoline sample. The method was adequate for the determination of Cu and Cr in gasoline samples collected from different gas stations in Salvador, BA, Brazil.     

ICP OES Simultaneous Determination of Ca,Cu, Fe,Mg, Mn,Na, and P in Biodiesel by Axial and Radial Inductively Coupled Plasma-Optical Emission Spectrometry

Abstract

A simple and rapid method for the simultaneous determination of seven trace elements in biodiesel by axial and radial view Inductively Coupled Plasma Optical Emission Spectrometry (ICP OES) is proposed, in which the sample is emulsified with Triton X-100 and water, and in which yttrium is employed as an internal standard. The better obtained quantification limits (10 s) were by axial view, 0.165, 0.099, 0.033, 0.007, 0.016, 0.132, 0.660 µg g^?1 for Ca, Cu, Fe, Mg, Mn, Na, and P, respectively, based on a sample mass of 1.0 g diluted to a final mass of 10 g in the analytical solution. Calibration was carried out with aqueous standards, thus avoiding the use of frequently instable organic standards. Elemental recoveries were in the range of 90 to 109% for all seven analytes studied, and also the precision of the method was satisfactory (RSD < 8%).     

Studies on the Particle Morphology of Waterborne Cationic Polyurethane/Polyacrylate Microemulsions

Polyurethane containing tertiary nitrogen atoms was synthesized from polyol, diphenylmethane diisoccyanate (MDI) and N‐methyl diethanolamine. The polymer was converted into cationomers by quarternizing with methacrylic acid (MAA) and then dispersed in water. In this reaction, methyl methacrylate (MMA) was used to decrease viscosity; at the same time, it was the monomer in the later reaction. Finally the cationic polyurethane dispersions were further polymerized with an oil‐soluble initiator, azobisisobutyronitrile (AIBN), water‐soluble initiator, K₂S₂O₈ (KPS) and the mixture of AIBN and KPS. The different emulsion particles with shell‐core structure, “invert” shell‐core structure and “irregular” sandwich structure were obtained; the morphological structures were characterized by TEM observation, FT‐IR and particle size analysis.