光寻址电位传感器的正交相位检波检测方法

光寻址电位传感器的幅度检测方法易受噪声干扰,灵敏度差,信噪比和精度低,且受调制光源的影响较大,影响检测结果的准确性.为此提出了一种基于正交相位检波的光寻址电位传感器检测方法.该方法是将光寻址电位传感器的输出光电流信号分别与两路正交信号相乘,通过低通滤波提取直流分量并相除,即可得到光寻址电位传感器的输出信号相位信息.与已有的光寻址电位传感器相位检测方法相比,该方法具有算法复杂度低、实时性高的优点.实验研究了调制光源光强对光寻址电位传感器幅度检测和相位检测的影响,对比分析了光寻址电位传感器的传统幅度检测方法与正交相位检波检测方法对pH检测的灵敏度、线性度及信噪比.结果表明,相比于幅度检测方法,调制光源光强对光寻址电位传感器的相位检测影响更小,在频率为10 kHz,pH的范围为1.68~10.01的情况下,相位检测方法比幅度检测方法测得的灵敏度增加了7 mV/pH,精度提高了14.9 mpH,非线性误差减小了0.003%,均方差减少了0.1051×10^-5,信噪比增加了8.2827 dB.该方法特别适用于弱光下的光寻址电位传感器检测.     

Extension of the range of resonator scanning spectrometer into submillimeter band and some perspectives of its further developments

Extension of the working frequency of modern resonator spectrometers into submillimeter wave range is described. Experimental record of atmospheric absorption spectrum covering 45-370 GHz range is demonstrated for the first time, and measured water vapor J′_{ka′, kc′}-J_{ka, kc} = 5_1,5-4_2,2 at 325 GHz line parameters are presented. For the first time pressure lineshift for the 325-GHz water vapor line is measured. Further extension of working range is discussed. New estimations of physical limits of time needed for measurements of absorption in the whole Backward Wave Oscillator (BWO) range are given for phase continuous synthesizer regime. Basic schemes of fast broadband continuous phase synthesized sources are discussed. Verification of the previous measurements of water vapor 3_1,3-2_2,0 at 183 GHz line parameters is presented. Comparisons with ringdown resonator spectrometers are given.     

Q value related mass determinations using a Penning trap

We report here about measurements of reaction and decay Q values by precise determination of pairs of atomic masses. These were performed with the Penning trap mass spectrometer SMILETRAP. Measurements with Penning traps give reliable and accurate masses, in particular Q values, due to the fact that certain systematic errors to a great deal cancel in the mass difference between the two atoms defining the Q value. Some Q values that are of fundamental interest will be discussed here, for example, a new Q value for the ⁶Li (n,γ) ⁷Li reaction, for the β-decay of tritium, related to properties of the electron neutrino mass, and for the neutrino-less double β-decay of ⁷⁶Ge, related to the question of whether the neutrino is a Majorana particle or not. In case of the latter two we report the most accurate Q values, namely 18,589.8(12) eV for the tritium decay and 2,038.997(46) keV for the neutrino-less double β-decay of ⁷⁶Ge.     

Quantitation in capillary electrophoresis-mass spectrometry

CE-MS has evolved into a strong alternative to LC-MS. Most of CE-MS applications deal with characterization and identification. However, quantitative aspects have gained importance in, e.g., pharmaceutical and biotechnological applications. Here we summarize and evaluate various methodological aspects in order to achieve sensitive and reproducible results. Similar to LC-MS, aspects of matrix influence on the electrospray process need to be carefully addressed when quantitative results are intended by CE-MS. Due to a more complicated coupling special emphasis needs to be put on the CE-MS interface. Generally linearity over more than three orders of magnitude can be achieved by CE-ESI-MS. Furthermore, a literature survey has been performed in order to give an overview over quantitative measurements performed by CE-MS. The precision can be doubled when changing from a structural related to an isotopically labeled internal standard. Thus a level of precision better than 5% RSD can be achieved.     

Robust estimates of the theoretical standard deviation to be used in interlaboratory precision experiments

Interlaboratory experiments often contain results that strongly deviate from other results obtained in the same laboratory under repeatability conditions, or laboratory means that strongly deviate from other laboratory means. In ISO 5725-2 [1] and IUPAC [2], the basic standards for the organisation and analysis of interlaboratory experiments for the determination of precision of a measurement method, outlier tests are performed in order to detect such situations and to finally decide whether these values are retained in the analysis or discarded as outliers. This outlier treatment, which always has a subjective aspect, becomes unnecessary by using robust estimates of the repeatability and reproducibility standard deviation. This paper proposes to use Rousseeuw’s Q _n as an extremely robust and efficient estimate of the standard deviation. Two examples show the performance of the new method.     

稀土在中国高新材料研制开发中的应用

我国在稀土资源和稀土原料的生产方面都居世界领先地位，近年来稀土高新材料的研制与开发也取得重大进展。本文概述了我国在稀土高新材料开发与研究方面的成果，指出今后应把稀土应用基础研究、中重稀土的应用研究和稀土在能源领域的应用研究作为重点进一步开展工作。     

Patterns in the precision of quantitative data from multicomponent gas chromatographic or gas chromatographic-mass spectrometric analysis

The dispersion of the quantitative results in the analysis of volatile compounds from multicomponent mixtures by different fractionation techniques (solid-phase microextraction and direct thermal desorption) followed by GC or GC-MS presents nonrandom patterns related to the existence of different factors in the fractionation process or in the chromatographic separation which affect, to a different extent, the recovery of the sample components. Statistical techniques have been used to show the relative importance of these factors. The improvement in data precision achieved by using volatile compound concentration ratios is discussed.     

Comparative analysis of bias in the collection of airborne pollutants: Tests on major aromatic VOC using three types of sorbent-based methods

This study was undertaken to establish one of the most reliable sampling methods and to precisely evaluate the bias involved in the collection of airborne pollutant samples. For the purpose of our study, we investigated the performance of three different types of sampling techniques by measuring major aromatic volatile organic compounds (VOC) in outdoor air; the target analytes specifically include benzene, toluene, ethylbenzene, and xylene (commonly called BTEX). As the first step of our approach, we designed and developed a multi-channel sampling system consisting of a six-port mass flow controller (SJU-MFC) system. Because this system allowed the collection of up to six replicate samples, our measurement results were analyzed and screened statistically for the derivation of high-quality BTEX data. The feasibility of this sampling system was further tested through a comparison with concurrent measurement data sets obtained by two additional, but independent, sampling techniques: (1) automatic continuous sampler (ACS) and (2) on-line GC (O-GC) system. Based on the data sets collected concurrently by three different sampling methods, we attempted to evaluate the compatibility of sampling techniques. Although the results obtained by SJU-MFC system were not statistically different from those of the O-GC system, they were moderately distinguishable from those of ACS. Such patterns were seen consistently, when examined by correlation analysis. The overall results of our study thus generally point out that the compatibility of data sets, when the proper caution is taken, improve significantly among different sampling methodologies.     

Precise and accurate quantitative C NMR with reduced experimental time

In order to detect small variations in ¹³C isotopomers concentrations, high sensitivity, accuracy and precision have to be achieved. To assess such criteria, when using ¹³C NMR, ¹³C bi-labelled ethanol has been proposed as a molecular probe. Advantage has been taken of the pre-established structural relationship between the peak areas of the ¹³C NMR spectrum of this molecule, i.e. the ratio of signal areas is set to a fixed value. It is shown that the quality performance, required by quantitative ¹³C NMR spectroscopy, is not affected by a large reduction of the repetition delay using relaxation reagents.     

蒸发器支撑板板孔精密测量系统

建立了蒸发器支撑板板孔精密测量系统,并提出了基于边缘约束条件的轮廓参量测量方法.首先采用图像处理技术将待测目标转化为二维离散坐标点,计算其最小外接矩形并对轮廓进行预定位;然后将轮廓分割成相互重合的"扩展邻域轮廓",建立以曲率角为原则的边缘约束算法对各轮廓段精确定界,实现对轮廓参量的精密测量.实验和误差分析表明,该系统测量准确度优于0.02mm,对具有复杂轮廓的零件参量测量有参考价值.