Formation of low-temperature deformation-induced segregations of nickel in Fe–Ni-based austenitic alloys

ABSTRACT

The authors present the results of an investigation in Fe–Ni-Cr austenitic alloys of the low-temperature deformation-induced segregations of nickel that form in the micro regions being (i) located close to grain- and subgrain boundaries and (ii) characteristic of the concentration and magnetic inhomogeneities indicated by the appearance of a dark diffraction contrast at the electron diffraction patterns taken from these regions typical (at the same time) of an enhanced value of Curie temperature. The observed effects were connected with the micro distortions caused by the local change of lattice parameter because of an increase in nickel concentration, as well as in the result of a magnetostriction dilatation. Using methods of the X-ray energy dispersive spectroscopy (XEDS) and atomic-probe body-section radiography (tomography – APT) has made it possible to determine the borders of those regions of austenite that were characteristic of an enhanced concentration of nickel in the fields of the localisation of a deformation-induced segregation of nickel in the vicinity of grain (subgrain) boundaries of austenitic alloys of the types Fe–13Cr–30Ni and Fe–37Ni–3Ti.     

ZnO nanowire lines and bundles: Template-deformation-guided alignment for patterned field-electron emitters

One-dimensional ZnO materials have been promising for field-emission (FE) application, but how to facially control the alignment of ZnO emitters is still a great challenge especially for patterned display application. Here, we report the fabrication of novel ZnO nanowire (NW) line and bundle arrays for patterned field-electron emitters. The effects of PS template size and heating time on the resulted ZnO nanoarrays were systematically studied. The deformation degree of PS templates was controlled and hence utilized to adjust the alignment of electrochemically deposited ZnO arrays. It was found that the length of NW lines and the density of NW bundles can effectively tuned by the PS template heating time. The optimal FE performance with turn-on electric field as low as of 4.4 V μm⁻¹ and the field-enhancement factor as high as of 1450 were achieved through decreasing the screening effect among the patterned field-electron emitters.     

基于DIS数字信息化系统对透光物质透光性能的研究

采用DIS数字信息化系统,对不同浓度的蓝墨水溶液在激光光源照射下的透射平均照度及照度分布图像进行实验研究,得到了平均照度值随溶液浓度变化的规律。对不同颜色塑料膜片对白炽灯光源透过照度值及照度分布图像进行实验研究得到及其相关之规律。     

Stress-Strain State in the Zone of Load Transfer in a Composite Specimen under Uniaxial Tension

The stress-strain state in the zone of load transfer in a uniaxially stretched specimen made of a unidirectional epoxy carbon-fiber-reinforced plastic (CFRP) is investigated. A parametric analysis of the influence of geometric and mechanical characteristics of the specimen on its stress-strain state is performed by means of finite-element modeling. The parameters allowing us to significantly reduce the dangerous concentration of transverse and tangential stresses are revealed. The mechanical tensile characteristics of a high-strength pultruded unidirectional CFRP are determined experimentally, and the size effect of its strength is estimated.     

双奇核136La的集体带结构

通过重离子核反应与在束γ谱的实验技术, 对A=130缺中子核区的双奇核¹³⁶La的高自旋态进行了研究, 所用核反应为¹³⁰Te(¹¹B,5n). 实验结果扩展了¹³⁶La的能级纲图, 包括3个集体转动带, 最高自旋态达20h. 对于\uppi h_{11/2}\otimes \upnu h_{11/2}$~带, 观测到了旋称反转与集体回弯现象. 通过系统学比较, 对旋称反转特性进行了讨论. 由推转壳模型的计算指出, 此集体回弯是由一对中子的角动量顺排引起的. 另外两个集体带为具有~$\gamma\approx -60^\circ$~的扁椭形变带, 其可能的组态为: $\uppi h_{11/2}\otimes \upnu g_{7/2}h_{11/2}^2$~与~$\uppi g_{7/2}\otimes\upnu g_{7/2}^2 d_{5/2} h_{11/2}^2$.     

Stability and Nonlinear Deformation of Cylindrical Grids

The general stability of single-layer cylindrical grids is studied in linear and nonlinear formulations. Dependence of the general buckling load on the geometry and stiffness parameters of a grid is established in an analytical form. Such grids are numerically analyzed for stability. It is established that the general buckling load is much less than the local buckling load. Typical general buckling modes are found. It is shown that such grids are weakly sensitive to imperfections     

Numerical Prediction of the Strain State of Thermoset Matrix/Mineral Filler Composite Plates

The numerical prediction of the fields of inelastic strains (the linear invariant of the tensor of inelastic strains) in thermoset polyester/marble filler composite plates is discussed. A uniformly distributed load is applied to the plates, which lie on a steel base. The strain fields are predicted by means of the boundary element method by using creep test data for the composites and the polyester matrix itself. Identical creep tests were performed for two ages of the materials (1 month and 13 years), which allowed evaluating the aging effect. The study is carried out in two stages. At the first stage, the application of the generalized Maxwell-Gurevich equation to the thermoset matrix/mineral filler composite is demonstrated. The model parameters determined from the experimental creep data is used for the second stage, where the state of inelastic strains in the plates is predicted by applying the boundary element method. The influence of composite formulation (filler content) and physical aging of the polyester matrix on the state of inelastic strains in the plates is shown.__________Russian translation published in Mekhanika Kompozitnykh Materialov, Vol. 41, No. 2, pp. 145–156, March–April, 2005.     

Mesoscopic details of crack tip deformation field by application of differential interference contrast method

An experimental method is developed to examine the near tip deformation at the mesoscopic scale level. The differential interference contrast (DIC) method is used by application of the Nomarski prism in polarized microscope for measuring the out of surface deformation. The method is very sensitive to small height changes detected by different interference color. Discussed are results for the crack tip deformation field.     

Structural developments in synthetic rubbers during uniaxial deformation by in situ synchrotron X‐ray diffraction

The molecular orientation and strain‐induced crystallization of synthetic rubbers—polyisoprene rubber, polybutadiene rubber, and butyl rubber [poly(isobutylene isoprene)]—during uniaxial deformation were studied with in situ synchrotron wide‐angle X‐ray diffraction. The high intensity of the synchrotron X‐rays and the new data analysis method made it possible to estimate the mass fractions of the strain‐induced crystals and amorphous chain segments in both the oriented and unoriented states. Contrary to the conventional concept, the majority of the molecules (50–75%) remained in an unoriented amorphous state at high strains. Each synthetic rubber showed a different behavior of strain‐induced crystallization and molecular orientation during extension and retraction. Our results confirmed the occurence of strain‐induced networks in the synthetic rubbers due to the inhomogeneity of the crosslink distribution. The strain‐induced networks containing microfibrillar crystals and oriented amorphous tie chains were responsible for the ultimate mechanical properties. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 956–964, 2004     

Toughness mechanism in polypropylene composites: Polypropylene toughened with elastomer and calcium carbonate

Polypropylene (PP) was modified with elastomer or CaCO₃ particles of two different sizes (1 μm and 50 nm) in various volume fractions. The dispersion morphology and mechanical properties of the two systems were investigated as functions of the particle size and volume fraction of the modifier. The brittle‐to‐tough transition occurred when the matrix ligament thickness was less than the critical ligament thickness, which was about 0.1 μm for the PP used here, being independent of the type of modifier. At the same matrix ligament thickness, the improvement of the toughness was obviously higher with the elastomer rather than with CaCO₃, but adding CaCO₃ increased the modulus of PP. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 1656–1662, 2004