氢化丁苯共聚物结构的核磁共振波谱表征Ⅱ.微观结构的定量计算

在氢化丁苯共聚物¹³C-NMR谱脂肪碳部分谱带归属的基础上,根据各谱带的主要来源,推导出六个二单元浓度的计算公式。计算出二单元、一单元的相对含量,各结构单元的数均序列长度、嵌段含量和其它结构参数。加氢前后的¹H-和¹³C-NMR谱的组成计算结果基本一致。初步探讨了作为粘度指数改进剂的氢化丁苯共聚物微观结构与性能的关系,为合成提供了依据。     

固体力学有限元体系的结构拓扑变化理论

本文是文[1]的继续.文[1]提出了杆件系统的结构拓扑变化理论和拓扑变化法本文将这一理论和方法推进到连续体有限元体系;且在此基础上揭示出有限元体系的一个新性质,称为基本位移之梯度的正交性定理,从而给出一套设计敏度的显式表达式,可直接用于计算.     

Diffusion Structural Analysis Study of Titania Films Deposited by Sol-Gel Technique on Silica Glass

The diffusion structural analysis (DSA) was used to characterize microstructure changes of hydrous titania gel films under in situ conditions of heating. TG and DTA were used in order to elucidate the processes controlling the formation of anatase film during heating of hydrous titania gel film. The annealing of porosity and near surface structure defects of the dehydrated titania films was indicated by DSA in the temperature range 255–700°C as the decrease of radon release rate. It was demonstrated that the annealing was enhanced on heating in oxygen in comparison with heating in argon. The DSA experimental results were compared with model curves describing the radon diffusion mobility and the annealing of radon diffusion paths.     

Structure and Structural Nonrigidity of Tetrachlorodibenzo-p-Dioxin Radical Cations

Ab initio calculations showed that the tetrachlorodibenzo-para-dioxin radical cations (TCDD RCs) with a planar structure have two steady states with asymmetric dioxin cycles. The activation barriers between these states are up to 2 kcal/mole, so that the RCs may be regarded as being structurally nonrigid within the dioxin cycle. The 2,3,7,8-TCDD RC is more stable than the 1,4,6,9-TCDD RC, the energy difference being 5.2 kcal/mole. The adiabatic ionization potential of 2,3,7,8-TCDD (7.54 eV) is 0.1 eV smaller than the corresponding potential of 1,4,6,9-TCDD. These factors account for the increased hemoproteide affinity and hence increased biological activity of 2,3,7,8-TCDD.     

Annealing behavior of gel‐spun polyethylene fibers at temperatures lower than needed for significant shrinkage

The annealing at 373 K of ultrastrong, gel‐spun polyethylene (PE) has been studied. At this temperature, the fibers show no significant shrinkage. Still, a significant decrease in the mechanical properties is observed. The fibers have been analyzed with differential scanning calorimetry (DSC), temperature‐modulated differential scanning calorimetry (TMDSC), atomic force microscopy (AFM), and small‐angle X‐ray scattering (SAXS). During the annealing, the glass transition of the intermediate phase is exceeded, as shown by DSC. When split for structure analysis by AFM, the annealed fibers undergo plastic deformation around the base fibrils instead of brittle fracture. The quasi‐isothermal TMDSC experiments are compared to the minor structural changes seen with SAXS and AFM. The loss of performance of the PE fibers at 373 K is suggested to be caused by the oriented intermediate phase, and not by major changes in the structure or morphology. The overall metastable, semicrystalline structure is shown by TMDSC to posses local regions that can melt reversibly. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 403–417, 2003     

Identifying Linking-Pin Organizations in Inter-Organizational Networks

Within the large literature on inter-organizational networks, there has been some discussion of linking-pin organizations and the role they play in integrating these networks. Based on this verbal specification of linking-pin organizations, we construct operational criteria and empirical methods for identifying these structurally important organizations in potentially large and complex inter-organizational networks. These methods are based on ideas drawn from blockmodeling, structural holes, centrality and centralization of networks, and identifying cut-points in networks. These methods are applied to a constructed example and then to real empirical inter-organizational networks. Implications and contrasts with other methods are discussed, together with some open problems.     

FexNi100−x nanometric films deposited by laser ablation on SiO2/Si substrates

Fe_xNi_100−x nanometric films were deposited on SiO₂/Si substrates at room temperature using the pulsed laser deposition technique. The targets were Fe-Ni amorphous magnetic foils with composition Fe₅₀Ni₅₀, Fe₃₅Ni₆₅ and Fe₂₂Ni₇₈. Morphological and structural properties of the deposited films were investigated using scanning electron microscopy, Rutherford backscattering spectrometry, grazing incidence X-ray diffraction, and X-ray reflectivity. Electrical and magnetic characteristics of the films were investigated by using the four-point probe and the magneto-optic Kerr effect techniques, respectively. The film properties are strictly dependent on the Fe-Ni compositional ratio.     

Crossover Critical Behavior in the Three-Dimensional Ising Model

The character of critical behavior in physical systems depends on the range of interactions. In the limit of infinite range of the interactions, systems will exhibit mean-field critical behavior, i.e., critical behavior not affected by fluctuations of the order parameter. If the interaction range is finite, the critical behavior asymptotically close to the critical point is determined by fluctuations and the actual critical behavior depends on the particular universality class. A variety of systems, including fluids and anisotropic ferromagnets, belongs to the three-dimensional Ising universality class. Recent numerical studies of Ising models with different interaction ranges have revealed a spectacular crossover between the asymptotic fluctuation-induced critical behavior and mean-field-type critical behavior. In this work, we compare these numerical results with a crossover Landau model based on renormalization-group matching. For this purpose we consider an application of the crossover Landau model to the three-dimensional Ising model without fitting to any adjustable parameters. The crossover behavior of the critical susceptibility and of the order parameter is analyzed over a broad range (ten orders) of the scaled distance to the critical temperature. The dependence of the coupling constant on the interaction range, governing the crossover critical behavior, is discussed.     

从结构电算谈设计概念

使用计算机进行结构设计虽然能大大减轻计算工作量，但不能取代人的设计概念，只有在设计人员具备较全面的设计概念；有一定设计经验；同时深入了解程度的情况下，才能确保工程设计的质量。     

Surface characterization and barrier properties of plasma‐modified polyethersulfone/layered silicate nanocomposites

This study describes the preparation of polyethersulfone (PES)/layered silicate nanocomposites (PLSNs) by mixing PES polymer chain into organically‐modified layered silicate in 1‐methyl‐2‐pyrrolidinone (NMP) solution. Both X‐ray diffraction data and transmission electron microscopy images of PLSNs indicate that the silicate layers were almost exfoliated and randomly distributed into the PES matrix. The mechanical and barrier properties of PLSNs show remarkable enhancement in the storage modulus and water/oxygen permeability when compared with that of neat PES matrix. Surfaces modification of PES and PLSN films with various treated times, system pressures, and radio frequency (RF) powers were performed using a mixture of oxygen (O₂) and nitrogen (N₂) plasmas. The topographical and physical properties of plasma‐modified PES and PLSN surfaces were investigated using scanning probe microscopy (SPM), contact‐angle measurements, and X‐ray photoelectron spectroscopy (XPS). These results indicate that the surface roughness of PLSNs with the same condition of plasma modification is lower than that of neat PES matrix and is probably due to the increase of stiffness with the presence of inorganic layered silicates in PES matrix. The surface properties of the PES and PLSNs are also changed from hydrophobic to hydrophilic. The XPS spectra suggest that the exposure of the PES and PLSNs to the plasmas led to the combination of etching reactions of polymer surface initiated by plasma and the following addition reactions of new oxygen‐ and nitrogen‐containing functional groups onto polymer surfaces to change their surface properties. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 3185–3194, 2006