Microstructural stability and age-hardening behavior of Re-added dual two-phase Ni3Al and Ni3V intermetallic alloys

The effect of Re addition on the microstructure and hardening behaviour of the dual two-phase Ni₃Al (L1₂) and Ni₃V (D0₂₂) intermetallic alloy was investigated by scanning electron microscopy, transmission electron microscopy and Vickers hardness test. The two-phase eutectoid microstructure accompanying the Re-rich precipitates were observed in the channel region of the alloys in which Re substituted for Ni but not in those in which Re substituted for Al and V. The concomitant addition of Nb (or Ta) with Re more stabilized the two-phase eutectoid microstructure and consequently more induced the fine precipitates in the channel region. The annealing at temperatures below the eutectoid temperature was necessary to induce the fine precipitates in the channel region and thereby result in the precipitation hardening. The fine precipitation in the channel region and related hardening was attributed to the alloying feature so that Re is soluble in the A1 (fcc) phase at high temperatures and becomes less soluble in the two intermetallic phases decomposed from the A1 phase at low temperatures.     

Diffusion Structural Analysis Study of Titania Films Deposited by Sol-Gel Technique on Silica Glass

The diffusion structural analysis (DSA) was used to characterize microstructure changes of hydrous titania gel films under in situ conditions of heating. TG and DTA were used in order to elucidate the processes controlling the formation of anatase film during heating of hydrous titania gel film. The annealing of porosity and near surface structure defects of the dehydrated titania films was indicated by DSA in the temperature range 255–700°C as the decrease of radon release rate. It was demonstrated that the annealing was enhanced on heating in oxygen in comparison with heating in argon. The DSA experimental results were compared with model curves describing the radon diffusion mobility and the annealing of radon diffusion paths.     

Polymerization of 1,3‐dienes with functional groups. III. Free‐radical polymerization of N,N‐diethyl‐2‐methylene‐3‐butenamide

Free‐radical homo‐ and copolymerization behavior of N,N‐diethyl‐2‐methylene‐3‐butenamide (DEA) was investigated. When the monomer was heated in bulk at 60 °C for 25 h without initiator, rubbery, solid gel was formed by the thermal polymerization. No such reaction was observed when the polymerization was carried out in 2 mol/L of benzene solution with with 1 mol % of azobisisobutyronitrile (AIBN) as an initiator. The polymerization rate (R_p) equation was R_p ∝ [DEA]^1.1[AIBN]^0.51, and the overall activation energy of polymerization was calculated 84.1 kJ/mol. The microstructure of the resulting polymer was exclusively a 1,4‐structure where both 1,4‐E and 1,4‐Z structures were included. From the product analysis of the telomerization with tert‐butylmercaptan as a telogen, the modes of monomer addition were estimated to be both 1,4‐ and 4,1‐addition. The copolymerizations of this monomer with styrene and/or chloroprene as comonomers were also carried out in benzene solution at 60 °C. In the copolymerization with styrene, the monomer reactivity ratios obtained were r₁ = 5.83 and r₂ = 0.05, and the Q and e values were Q = 8.4 and e = 0.33, respectively. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 999–1007, 2004     

The role of alkali content in the devitrification mechanisms of SiO2–Fe2O3–Na2O–PbO SYSTEM

Three batch compositions of pure oxides (SiO₂, Fe₂O₃, PbO, Na₂O) with equivalent SiO₂, Fe₂O₃ and PbO contents and a gradually increased Na₂O content were vitrified through heating in a high temperature electric furnace and subsequent quenching. The resulting vitreous products were thermally treated in order to study the devitrification behaviour, under conditions designated from differential thermal analysis experiments. Depending on the Na₂O content, crystal phase separation gave rise to the growth of acmite and hematite or maghemite. A uniformly phase separated glass-ceramic material, with crystallites of similar size and population density, was produced from devitrification of the vitreous product with the higher Na₂O content.     

轻型汽车后桥半轴断裂件的组织及断口特征

采用光学显微镜和扫描电子显微镜等手段，对某轻型汽车40Cr后桥半轴断裂件的组织及断口特征进行了分析结果表明：半轴在调质处理时的淬火温度不够高，使其表层和心部组织中存在较多的铁素体相，造成了工件最终的硬度和疲劳强度不足，导致半轴在使用中发生扭转疲劳断裂．     

Proteinases from Carica papaya Latex

Data on the proteinase complex from Carica papaya latex were reviewed. The properties and applications of the domestic preparation cucumazyme and known medicinal preparations based on papaya proteinases (caripazyme, lecozyme, lecopain) were compared.     

Adhesion studies of latex film surfaces on the meso- and nanoscale

In this paper the effects of surface roughness and annealing temperature (T) of latex coating films on adhesion are discussed for the different stages of the film formation process. The surface free energy of latex films was assessed in terms of practical work of adhesion (W) (or adherence) using a custom-built adhesion-testing device (ATD), atomic force microscopy (AFM), and contact angle measurements. For preannealed latex films surface roughness averages (R_a) were determined from AFM height images and were related to the values of W obtained from ATD measurements at room temperature. The results obtained using these tests exhibiting surface behavior on different length scales indicate a dependence of the measured adhesion on surface roughness and temperature, as well as on the length scale of the measurements.First preannealed samples were studied, which were obtained by heat treatment above the respective glass transition temperatures (T_g). Increasing the temperature of preannealing resulted in a decrease of the adherence observed in ATD experiments at room temperature. However, on the nanoscale, using AFM, no significant variation of the adherence was observed. This observation can be explained by roughness arguments. Preannealing decreases roughness which results in lower adherence values measured by ATD while for essentially single asperity AFM experiments roughness has an insignificant effect. Specimens were also annealed over a constant period of time (90 min) at different temperatures. At the end of the heat treatment, adhesion was measured at the treatment temperature by ATD. The amplified effect of temperature observed in this case on adherence is attributed to the combination of roughness decrease and increasing test temperature. In a third set of experiments completely annealed samples were studied by ATD as well as by AFM as a function of temperature. With increasing T values ATD showed a decrease in adherence, which is attributed to a decreasing surface free energy of the annealed films at elevated T values. AFM, on the other hand, showed an opposite trend which is assigned to increasing penetration of the tip into the tip/wetting polymer samples versus increasing temperature. Finally, annealing isotherms as a function of time were investigated by ATD in situ at different temperatures. This last set of experiments allowed us to optimize annealing time and temperature to achieve complete curing.     

乳液聚合阶段Ⅱ动力学研究的进展

本文简述了乳浓聚合动力学研究的进展,着重于澳大利亚Sydney大学Gilbert等在乳液聚合阶段Ⅱ动力学方面的研究概况。介绍了不同水溶性单体的小尺寸种子乳液体系的SmithEwart递推方程的求解方法及其解析解形式和乳液聚合动力学数据的处理。同时讨论了该研究的局限性。     

Cu-MgF2复合纳米金属陶瓷薄膜的电导特性研究

用射频磁控共溅射法制备了Cu体积分数分别为 10 % ,15 % ,2 0 %和 3 0 %的Cu MgF2 复合金属陶瓷薄膜 .用x射线衍射、x射线光电子能谱和变温四引线技术对薄膜的微结构、组分及电导特性进行了测试分析 .微结构分析表明 :制备的Cu MgF2 复合薄膜由fcc Cu晶态纳米微粒镶嵌于主要为非晶态的MgF2 陶瓷基体中构成 ,Cu晶粒的平均晶粒尺寸随组分增加从 11 9nm增至 17 8nm .5 0— 3 0 0K温度范围内的电导测试结果表明 :当Cu体积分数qM 由 15 %增加到 2 0 %时 ,Cu MgF2 复合薄膜的电阻减小了 8个量级 ,得出制备的复合薄膜渗透阈qCM 应处于 15 %和 2 0 %之间 .qM 在 10 %和 15 %之间的薄膜呈介质导电状态 ,而在 2 0 %和 3 0 %之间的薄膜则呈金属导电状态 .从理论上讨论了复合薄膜中杂质电导和本征电导的激活能及其对电导的贡献 ,并讨论了Cu MgF2 复合纳米金属陶瓷薄膜的渗透阈 ,得到了和实验一致的结果     

The fabrication and characterization of poly(lactic acid) scaffolds for tissue engineering by improved solid–liquid phase separation

In this article a new technique was developed to fabricate scaffolds with a unique microstructure by solid–liquid separation in combination with particulate-leaching. Firstly, the effects of polymer concentration, quenching temperature on the porous morphology and the mechanical property of obtained scaffolds during solid–liquid separation have been investigated. Then, salt granules as porogen were introduced into the solid–liquid phase separation to produce the unique pore structure of the scaffold. The pore diameter of the scaffold could be controlled with the particulate size and the wall of pores possessed special microstructure, which enhanced the pore interconnectivity. The cell culture results confirmed that a good interconnectivity of the scaffold prepared by the improved solid–liquid separation was useful for nutrition transportation and cell proliferation. Copyright © 2003 John Wiley & Sons, Ltd.