TDI三聚体的合成研究

以一种碱金属羧酸盐K-1000作为甲苯二异氰酸酯(TDI)三聚反应的催化剂合成了以TDI三聚体为主要成分的多异氰酸酯固化剂。对合成工艺条件进行了探讨。结果表明,将反应温度控制在35℃,催化剂K-1000用量为0.06%时,用苯甲酰氯作为阻聚剂可得到性能基本稳定的TDI三聚体产品。     

A ONE-STEP SURFACE MODIFICATION PROCEDURE TO PEG-GRAFTED NANO-TITANIA

PEG （Polyethylene Glycol）-grafted nano-titania has been obtained in a one-step procedure using hexamethylene diisocyanate as the coupling agent and dibutyltin dilaurate as the catalyst in toluene at 80℃ and characterized qualitatively by FTIR and quantitatively by elemental analysis and thermogravimetric analysis. A comparison of nano-titania with two other commonly used inorganic nanoparticles, nano-silica and nano-alumina, is made, revealing that reactivity order is nano- silica 〉 nano-alumina 〉 nano-titania in view of PEG grafting. Possible mechanism of PEG grafting is also discussed.     

HTPB／TDI,HDI聚合反应动力学研究

对端羟基聚丁二烯／甲苯二异氰酸酯，端羟基聚丁二烯／己二异氰酸酯甲苯溶液体系进行了反应动力学研究，用基团分析方法计算了相应体系的活化能，并对无催化剂和有催化剂的体系作了比较。结果表明，二丁基二月桂酸象对上述体系有强的催化作用，使体系的活化能降低，反应速度加快。对于对端差基聚丁二烯／甲苯二异氰酸酯体系，无催化剂时前后期反应活化能分别为２９．１ｋＪ／ｍｏｌ、３７．４ｋＪ／ｍｏｌ，有催化剂时前后期反应活化     

Hydrolyzable poly(ester-urethane) networks from L-lysine diisocyanate and D,L-lactide/ϵ-caprolactone homo- and copolyester triols

Bioabsorbable poly(ester-urethane) networks were synthesized from ethyl 2,6-diisocyanatohexanoate (L -lysine diisocyanate) (LDI) and a series of polyester triols. LDI was synthesized by refluxing L-lysine monohydrochloride with ethanol to form the ester, which was subsequently refluxed with 1,1,1,3,3,3-hexamethyldisilazane to yield a silazane-protected intermediate. This product was then phosgenated using triphosgene. Polyester triols were synthesized from D,L-lactide, ?-caprolactone, or comonomer mixtures thereof, using glycerol as initiator and stannous octoate as catalyst. Polyurethane networks were cured using [NCO]/[OH] = 1.05 and stannous octoate (0.05 wt %) for 24 h at room temperature and pressure and 24 h at 50°C and 0.1 mm Hg. LDI-based polyurethane networks were totally amorphous and possessed very low sol contents. Networks based on poly (D,L-lactide) triols were rigid (T_g ∽ 60°C) with ultimate tensile strengths of ～ 40–70 MPa, tensile moduli of ～ 1.2–2.0 GPa, and ultimate elongations of ～ 4–10%. Networks based on ?-caprolactone triols were low-modulus elastomers with tensile strengths and moduli of ～ 1–4 MPa and ～ 3–6 GPa, respectively, and ultimate elongations of ～ 50–300%. Networks based on copolymers displayed physical properties consistent with monomer composition and were tougher than the networks based on the homopolymers. Tensile strengths for the copolymers were ～ 3–25 MPa with ultimate elongations up to 600%. Hydrolytic degradation under simulated physiological conditions showed that D ,L -lactide homopolymer networks were the most resistant to degradation, undergoing virtually no change in mass or physical properties for 60 days. ?-Caprolactone-based networks were resistant to degradation for 40 days, and high-lactide copolymer-based networks suffered substantial losses in physical properties after only 3 days. © 1994 John Wiley & Sons, Inc.     

二氧化碳—环氧丙烷—甲苯二异氰酸酯的三元共聚

二氧化碳和环氧丙烷(PO)在阴离子配位催化剂,如二乙基锌和等摩尔的水作用下,可接式(1)发生共聚。但产物聚丙撑碳酸酯(PPC)的热稳定性较差。改进途径之一是在反应中引入甲苯二异氰酸酯(TDI)进行三元共聚。本文报导在双金属阴离子配位催化剂PBM存在下合成一种热稳定性优于PPC的聚碳酸酯聚氨酯(PCPU)的研究结果(式2)。     

Investigation of a cylindrical chemosorptive denuder for sampling and phase separation of toluene diisocyanate aerosols

A cylindrical chemosorptive denuder in series with a glass fibre filter has been evaluated for sampling toluene diisocyanate (TDI) aerosols. The sampler is designed for measuring personal exposure to diisocyanates. Several denuder coatings and derivatising reagents were investigated. Dimethylpolysiloxane (SE-30) and 5% phenyl dimethylpolysiloxane (SE-54) with either dibutylamine (DBA) or dipentylamine (DPeA) as derivatising reagents yielded the lowest vapour breakthrough (the amount (%) of the vapour that passes through the denuder), close to values predicted by theory. Immobilisation of the SE-30 denuder coating by in-situ cross-linking yielded comparable results. With an SE-30/DBA-coated denuder operating within an airflow range of 100–500 mL min^–1, the phase separation was shown to be consistent with theoretical predictions derived by use of the Gormley–Kennedy equation. This provides a means of calculating the vapour breakthrough and correcting experimentally obtained values with regard to vapour–particulate phase distribution, suggesting that the denuder can provide accurate phase-distribution measurements. The SE-30/DBA denuder can be used over a concentration range spanning nearly six orders of magnitude. Its capacity is sufficient to perform 15-min exposure measurements of a TDI aerosol with air concentrations as high as 1,700 g m^–3, 40 times higher than the Swedish occupational exposure limit (OEL). At the other end of the range, the estimated limit of detection (LOD) was less than 2 ng m^–3 for both the vapour and the aerosol phases when LC–ESI–MS–MS was used for chemical analysis.Electronic Supplementary Material Supplementary material for this article is available at     

Clickable polyurethanes based on s‐triazine ring containing aromatic diisocyanate bearing pendent alkyne group: Synthesis and postmodification

A new s‐triazine ring containing aromatic diisocyanate bearing a pendent alkyne group, namely, 2,4‐bis(4‐isocyanatophenoxy)?6‐(prop‐2‐yn‐1‐yloxy)?1,3,5‐triazine was synthesized and reacted with various diols viz., 1,10‐decanediol, tetraethylene glycol and polyethylene glycols in the presence of dibutyltin dilaurate as the catalyst to obtain a series of linear polyurethanes. The selected polyurethanes possessing pendent alkyne groups were postmodified with chemically diverse azides viz., 1‐(azidomethyl)benzene, 1‐(azidomethyl)pyrene, and methoxy end‐caped poly(ethylene glycol) azide via copper‐catalysed azide‐alkyne Huisgen 1,3‐dipolar cycloaddition. FTIR and ¹H NMR spectra indicated quantitative click reaction. UV–vis and fluorescence spectroscopic analysis confirmed complete incorporation of pyrenyl groups indicating the formation of fluorescence active polyurethane by postmodification with 1‐(azidomethyl)pyrene. TG analysis of polyurethanes indicated two stage weight loss and their thermal stability, as judged by T ₁₀ values, was governed by weight percent of urethane linkages. The water contact angle measurements revealed improved wettability with increased content of PEG either in the backbone of polyurethanes or as grafted chains. DLS and TEM studies confirmed that certain polyurethanes possessing PEG segments displayed self‐assembly in aqueous solution, which was further supported by pyrene encapsulation studies using UV–vis spectroscopy. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55 , 1008–1020     

Solvent‐Free Claisen Condensation of Isophorone and Verbenone with para‐Hydroxyethylaminobenzaldehydes

A solvent‐free Claisen condensation between isophorone or verbenone on two para‐hydroxyethylaminobenzaldehydes is described. The method provides the condensation products quickly and, in most cases, without chromatography.     

Studies on novel thermally stable segmented polyurethanes based on thiourea-derivative diols

Novel thermoplastic segmented poly(urethane-thiourea)s (PURs) were synthesized via one-step polymerization from aromatic diols containing sulfur (thiourea linkage) in the main-chain, including terephthaloyl bis (3-(2-hydroxopyridyl) thiourea) (TBHPT) and terephthaloyl bis (3-(5-naphtholyl) thiourea) (TBNT), along with 1,4-phenylene diisocyanate (PDI) as hard segment and 20, 50 and 80 mol% polyethylene glycol (PEG) as a soft segment. The prepared chain extenders and polymers were characterized by conventional methods, and physical properties such as η_inh, solubility, thermal stability and thermal behavior were studied. Easily processable PURs with excellent thermal stability were obtained by incorporating 20 mol% PEG in the soft segment. Thermogravimetric analysis indicated that poly(urethane-thiourea)s were fairly stable above 500 °C and own high glass transition temperatures about 263-266 °C. These polymers also showed partially crystalline structures. Ultimately, weight average molecular weights (M_w) of PURs were up to 109 × 10³. Compared to typical polyurethanes, PURs exhibited better thermal stability and T_g’s owing to rigid hard segment structure.     

扩链法合成聚乳酸类生物降解材料

详细地综述了聚乳酸类生物降解材料的扩链法合成，特别是使用二异氰酸酯类、二恶唑淋类扩链剂的合成进展。参考文献37篇。