Investigation on crosslinking behaviors of NBR/PVC filled with anhydrous copper sulfate particles by dynamic mechanical analysis

Crosslinking behaviors of acrylonitrile butadiene rubber (NBR)/poly (vinyl chloride) (PVC) alloy, filled with anhydrous copper sulfate (CuSO₄) particles, were investigated for the first time by dynamic mechanical analysis (DMA) under hetero and isothermal modes, respectively. In the heterothermal testing, (NBR/PVC)/CuSO₄ compound showed two marked increases in the storage modulus (E′), corresponding to coordination crosslinking of NBR-CuSO₄ and self-crosslinking of NBR and PVC respectively. During the isothermal testing, a dramatic increase in E′ was found at the initial stage while that of original NBR/PVC alloy was not detected. The marked increase in E′ of (NBR/PVC)/CuSO₄ compound was mainly due to the crosslinking induced by coordination between  CN and Cu²⁺. The increasing extent of E′ increased with the rise of CuSO₄ content, suggesting the formation of a greater number of crosslinks. Moreover, the activation energy (E_a) of crosslinking process was about 139 kJ/mol. In this work, fourier transform infrared spectrum (FT-IR) and equilibrium swelling method were also performed for the characterization of the compound. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 41–51, 2007     

Dynamic mechanical analysis

Using dynamic mechanical analysis (DMA) we have studied thermal degradation for a system containing a diglycidyl ether of bisphenol A (DGEBA) and 1,3-bisaminomethylcylohexane (1,3-BAC). The changes of dynamic mechanical properties during thermal degradation indicated a shift of the glass transition temperature (T _g) to higher temperatures and a decrease in the peak value of the dynamic loss factor (tan δ) with an increasing of aging time. The value of dynamic storage modulus (E′) at the rubbery state showed an increase with aging time, whiteE′ at the glassy state only underwent a moderate change with increased thermal degradation. From these results it can be argued that thermal degradation during the stage prior to the onset of the severe degradation involves structural changes in the epoxy system, as further crosslinking and loss of dangling chains in the crosslinked network.     

Mechanical analysis on rocket propellants

The mechanical properties of solid rocket propellants are very important for good functioning of rocket motors. During use and storage the mechanical properties of rocket propellants are changing, due to chemical and mechanical influences such as thermal reactions, oxidation reactions or vibrations. These influences can result in malfunctioning, leading to an unwanted explosion of the rocket motor. Most of modern rocket propellants consist of a polymer matrix (i.e. HTPB) filled with a crystalline material (i.e. AP, AN). However, the more conventional double base propellants consist of a solid gel matrix with additives, such as stabilizers. Both materials show a mechanical behaviour, quite similar to that of general polymers. To describe the material behaviour of both propellants a linear visco-elastic theory is often used to describe the mechanical behaviour for small deformations. Because the time-temperature dependency is also valid for these materials a mastercurve can be constituted. With this mastercurve the response properties (stiffness) under extreme conditions can be determined. At TNO-PML a mastercurve of a double base propellant was constituted using dynamical mechanical analysis (DMA) and compared with a mastercurve reduced from conventional (static) stress relaxation tests. The mechanical properties of this double base propellant determined by DMA were compared with conventional (quasi-static) tensile test results. This revised version was published online in July 2006 with corrections to the Cover Date.     

Water absorption of a diglycidyl ether of bisphenol A/1,3-bisaminomethylcyclohexane (DGEBA/1,3-BAC) epoxy resin system

The diffusive and dynamic mechanical behavior of the DGEBA/1,3-BAC epoxy resin system was studied during water absorption. The diffusion of water was investigated at 100% relative humidity, by immersion of specimens in water at 60, 80 and 100°C. In all absorption experiments, water diffusion followed Fick's law. Diffusion coefficients and saturated water concentrations are given for these temperatures. The activation energy for diffusion was determined from the relationship between the diffusion coefficient and the reciprocal of the absolute temperature. The value obtained was 31.2 kJ mol^–1. Dynamic mechanical analysis of samples immersed in 100°C water and with various water contents showed both a shift of T_g, defined by thetan peak, to lower temperatures and a slight decrease in the dynamic modulus in the presence of water. These effects are probably a result of plasticization.This work was supported by the Xunta de Galicia through grant XUGA-17201A92.     

Thermoanalytische Charakterisierung Strahlengehärteter Polymerfilme

Thermo-oxidative and thermo-mechanical stabilities of radiation-cured acrylates and epoxides were examined by TG, DMA and DSC.The polymeric trifunctional acrylates PETIA, TMPTA and THEIC displayed the highest temperatures of onset of degradation. The high crosslinking density of the films resulted in an almost temperature-independent complex E-modulus, as measured by DMA. With increasing degree of ethoxylation or propoxylation of the monomers, decreases in thermal stability and strength were found. For difunctional polymeric acrylates and epoxides, the glass transition temperature was measured.The average degree of curing of UV-cured epoxy films can be determined from the temperature of the maximum in the loss modulus (E_max.This revised version was published online in November 2005 with corrections to the Cover Date.     

Influence of the thermal degradation on the dielectric properties of a thermoset

The thermal degradation of an epoxy system consisting of a diglycidyl ether of bisphenol A (DGEBA, n=0) and m-xylylenediamine (m-XDA) was studied by both thermogravimetric analysis (TG) and dielectric analysis (DEA). It has been checked a deviation of the typical behaviour in the Arrhenius plot expected for this kind of systems, owing to the thermal degradation. Both, structural relaxation time and conductivity values, were represented as a function of the mass loss, that allow a relationship to be obtained between characteristic relaxation time and the degree of degradation at the beginning of the degradation process.     

Complexation of an acrylic resin by tertiary amines: synthesis and characterisation of new binders for antifouling paints

Antifouling coatings are the most reliable way to prevent biofouling of immersed surfaces. As concerning the high toxicity of organotin paints, the tendency is the development of coatings, which do not present environmental risks. In this work, we prepare binders from modification of acrylic copolymers containing free carboxylic acid groups. Biocides chosen are tertiary ammonium salts; alkyl chain substituents with different length are considered. The chemical modifications of resins are carried out via a single step reaction. Modification extents are monitored through proton nuclear magnetic resonance and thermogravimetric analysis and the modified resins are characterised by Fourier transform infrared spectroscopy. The glass transition temperature of the acrylate systems is assessed by dynamical mechanical analysis (pin point method) and compared with data obtained by differential scanning calorimetry. The erosion and antifouling properties of the binders are followed during an exposure to marine environment by a visual observation.     

Elastic Moduli and Activation Energies for an Epoxy/m-XDA System by DMA and DSC

The influence of the resin/diamine ratio on the properties of the system diglycidyl ether of bisphenol A (BADGE n=0/m-xylylenediamine) (m-XDA) was studied. Variation of this ratio resulted in significant effects on the cure kinetics and final dynamic mechanical properties of the product material. The study was made in terms of storage modulus (E′), vss modulus (E″) and molecular mass between cross-links (M_c) at different ratios. Two geometries (cylindrical and rectangular) were considered. The influence of temperature was studied through the activation energy (E_a>), which depends on the epoxy/amine ratio and the geometry of the samples. Glass transition temperatures (T_g>) and glass transition temperatures for thermosets with null degree of conversion (T_go>) were determined by DSC. T_g> decreases when amounts of curing agent greatly in excess of the stoichiometric composition were used. This revised version was published online in July 2006 with corrections to the Cover Date.     

Interactions of Some Amino Acids with Aqueous N,N-Dimethylacetamide Solutions at 298.15 and 308.15 K: A Volumetric Approach

The apparent molar volumes, V _φ , of glycine, L-alanine and L-serine were obtained in aqueous 0 to ∼4 mol⋅kg⁻¹ N,N-dimethylacetamide (DMA) solutions from density measurements at 298.15 and 308.15 K. The standard partial molar volume, V _φ ^o, and standard partial molar volumes of transfer, Δ_tr V _φ ^o, were determined for these amino acids. It has been shown that hydrophilic-hydrophilic interactions between charged groups of the amino acids and the —CON= group of DMA are predominant in the case of glycine and L-serine, but for L-alanine the interactions between its side group (—CH₃) and DMA are predominant. An increase in temperature increases the standard partial molar volumes but decreases the transfer volumes of the amino acids. The results have been interpreted in terms of cosphere overlap model.