A post curing strategy toward the feasible covalent adaptable networks in polyacrylate latex films

The implementation of covalent adaptable networks (CANs) in general resin system is becoming attractive. In this work, we propose a simple post-curing strategy based on the core-shell structured acrylate latex for the achievement on both the improved general performance and the CANs characteristics in latex films. The building to the CANs was relied on the introduction of 4,4′-diaminophenyl disulfide as the curing agent, which cured the acetoacetoxy decorated shell polymer through the ketoamine reaction. The metathesis reaction of aromatic disulfides in the crosslinking segments enabled the thermally induced dynamic behavior of the network as revealed in the stress relaxation tests by comparison with other diamine crosslinking agents without the incorporation of disulfide. The synergism of the dynamic crosslinking of the shell polymer and static crosslinking in the core polymer contributed to the improved mechanical strength (15 MPa, strain% = 250%) and the suppressed water adsorption (~1% in 24 h of soaking) of the latex film, which exhibited above 90% of recovery in both strength and strain from a cut-off film damage within 1 h at 80°C. Moreover, the cured latex film could be recycled, and 75% of the mechanical performance was regained after three fragmentation-hot-pressing cycles. These, in addition with the feasible and environmental friendly characteristics, suggest a sustainable paradigm toward the smart thermosetting latex polymers.     

Near-Ultraviolet Circular Dichroism and Two-Dimensional Spectroscopy of Polypeptides

A fully quantitative theory of the relationship between protein conformation and optical spectroscopy would facilitate deeper insights into biophysical and simulation studies of protein dynamics and folding. In contrast to intense bands in the far-ultraviolet, near-UV bands are much weaker and have been challenging to compute theoretically. We report some advances in the accuracy of calculations in the near-UV, which were realised through the consideration of the vibrational structure of the electronic transitions of aromatic side chains.     

A technical review of face mask wearing in preventing respiratory COVID-19 transmission

Since the outbreak of the COVID-19 pandemic, most countries have recommended their citizens to adopt social distance, hand hygiene, and face mask wearing. However, wearing face masks has not been well adopted by many citizens. While the reasons are complex, there is a general perception that the evidence to support face mask wearing is lacking, especially for the general public in a community setting. Face mask wearing can block or filter airborne virus-carrying particles through the working of colloid and interface science. This paper assesses current knowledge behind the design and functioning of face masks by reviewing the selection of materials, mask specifications, relevant laboratory tests, and respiratory virus transmission trials, with an overview of future development of reusable masks for the general public. This review highlights the effectiveness of face mask wearing in the prevention of COVID-19 infection.     

Mono-Aryl/Alkylthio-Substituted (Hetero)acenes of Exceptional Thermal and Photochemical Stability by the Thio-Friedel–Crafts/Bradsher Cyclization Reaction

The highly substituted mono-aryl/alkylthio-(hetero)acenes prepared in this study have been found to be thermally more stable (T_decomp.=331–354 °C) than the known di-aryl/alkylthio-substituted acenes by an average of 25 °C. They are also much more photostable at 254 and 365 nm (in both argon and air) than the parent anthracene and other reported anthracenes. The most photostable aryl/alkylthio-anthracenes at 254 nm were found to be 60–70 (in air) and 130 (in argon) times more stable in solution than the unsubstituted anthracene, and much more stable than known EDG/EWG-substituted anthracenes (EDG=electron-donating group, EWG=electron-withdrawing group) with an extended aromatic core. Furthermore, the acenes showed significantly higher photostability at 365 nm in both air and argon. The anthracenes were obtained by the novel thio-Friedel–Crafts/Bradsher cyclization reaction of hitherto unknown [o-(1,3-dithian-2-yl)aryl](aryl)methyl thioethers. The developed approach provides a general access to mono-aryl/alkylthio-substituted (hetero)acene frameworks containing at least three fused (hetero)aromatic rings. The characteristic feature of this approach, which leads to highly substituted acenes, is that the substituents, unlike in other methods, may be introduced at an early stage of the synthesis. DFT and TD-DFT calculations confirmed the stabilizing role of the aryl/alkylthio substituent in the mono-aryl/alkylthio-substituted anthracenes, which are the most stable anthracenes prepared to date. Their high photostability is mainly due to the quenching of singlet oxygen by the acene and the quenching of the acene S₁ state by molecular oxygen.     

Donor-acceptor copolymers from cyclopentannulation polymerizations with dicyclopenta[cd,jk]pyrene and dicyclopenta[cd,lm] perylene acceptors

A series of donor-acceptor copolymers with dicyclopenta[cd,jk]pyrene and dicyclopenta[cd,lm]perylene acceptor units was prepared via palladium catalyzed cyclopenta-annulation reactions. The acceptor units were paired with diethynyl containing donor groups based on benzo[1,2-b:4,5-b’]dithiophene, thieno[3,2-b]thiophene, and 4-octyl-4H-dithieno[3,2-b:2′,3′-d]pyrrole to create six polymer variants. The cyclopentannulation polymerization resulted in copolymers with molecular weights (Mn) of 6–14 kDa and broad light absorption in the visible region with band gaps of 1.38–1.85 eV. The synthetic methodology, as well as optoelectronic properties, including thin-film absorption and cyclic voltammetry, of the donor-acceptor copolymers are presented.     

Preparation of 3-substituted and 2,3-disubstituted-4,4,4-trifluoro-2-butenoic acids—Perkin condensation of activated aromatic ketones

The Perkin reaction of the activated aromatic ketones (2,2,2-trifluoroacetophenone and its 4′-phenyl-derivative) with various condensing agents (acetic anhydride, propionic anhydride, phenylacetic acid/acetic anhydride) gives the title compounds in good or moderate yields, and high E-stereoselectivity. For some derivatives an appreciable amount of the Z isomer was also formed. Several of the resulting butenoic acids and their methyl esters are synthesised and characterised for the first time.     

Multicyclic polyethers derived from 1,1,1‐tris(4‐hydroxyphenyl)ethane and 2,6‐dihalopyridines

Poly(pyridine ether)s were prepared in two ways: the polycondensation of silylated 1,1,1‐tris(4‐hydroxyphenyl)ethane (THPE) with 2,6‐difluoropyridine (method A) and the polycondensation of free THPE with 2,6‐dichloropyridine (method B). With method A, the THPE/difluoropyridine feed ratio was varied from 1.0:1.0 to 1.0:1.6. Cycles, bicycles, and multicycles were the main reaction products, and crosslinking was never observed. When ideal stoichiometry was used exclusively, multicycles free of functional groups were obtained. These multicycles were detectable in matrix‐assisted laser desorption/ionization time‐of‐flight (MALDI‐TOF) mass spectra up to B₃₈C₇₆ with a mass of approximately 32,000 Da. With method B, the reaction conditions were varied at a fixed feed ratio to achieve an optimum for the preparation of multicyclic polyethers, but because of the lower reactivity of 2,6‐dichloropyridine, a quantitative conversion was not achieved. The reaction products were characterized with MALDI‐TOF mass spectrometry, viscosity measurements, and size exclusion chromatography. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 5725–5735, 2004     

Structure,morphology, and crystallization process of isotactic polypropylene/hydrogenated hydrocarbon resin blends

The structure, morphology, and isothermal and nonisothermal crystallization of isotactic polypropylene/low‐molecular‐mass hydrocarbon resin blends (iPP/HR) (up to 20% in weight of HR) have been studied, using optical and electron microscopy, wide‐ and small‐angle X‐ray and differential scanning calorimetry. New structures and morphologies can be activated, using appropriate preparation and crystallization conditions and blend composition. For every composition and crystallization condition, iPP crystallizes in α‐form, with a spherulitic morphology. The size of iPP spherulites increases with resin content, whereas the long period decreases. In the range of crystallization temperatures investigated, HR modifies the birefringence of iPP spherulites, favoring the formation of radial lamellae and changing the ratio between tangential and radial lamellae. Spherulitic radial growth rates, overall crystallization rates, and melting temperatures are strongly affected by resin, monotonically decreasing with resin content. This confirms miscibility in the melt between the two components of the blends. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 3368–3379, 2004     

Miscible blends of modified poly(aryl ether ketones) with aromatic polyimides

The phase behavior of binary blends of poly(ether ether ketone) (PEEK), sulfonated PEEK, and sulfamidated PEEK with aromatic polyimides is reported. PEEK was determined to be immiscible with a poly(amide imide) (TORLON 4000T). Blends of sulfonated and sulfamidated PEEK with this poly(amide imide), however, are reported here to be miscible in all proportions. Blends of sulfonated PEEK and a poly(ether imide) (ULTEM 1000) are also reported to be miscible. Spectroscopic investigations of the intermolecular interactions suggest that formation of electron donoracceptor complexes between the sulfonated/sulfamidated phenylene rings of the PEEKs and the n-phenylene units of the polyimides are responsible for this miscibility. © 1993 John Wiley & Sons, Inc.     

氢氟烃/烷烃二元混合物的气液相平衡

整理了已公开发表的氢氟烃(HFC)/烷烃(HC)二元混合物气液相平衡实验数据,对实验数据进行了热力学一致性检验。采用PR方程加van der Waals混合规则描述该类混合物的气液相平衡性质,优化得到了11种混合物的二元交互作用系数,经比较表明采用优化结果能够高精度再现气液相平衡实验数据,比k_(ij)取0的计算结果有很大改善.