3D‐morphology reconstruction of nanoscale phase‐separation in polymer memory blends

In many organic electronic devices functionality is achieved by blending two or more materials, typically polymers or molecules, with distinctly different optical or electrical properties in a single film. The local scale morphology of such blends is vital for the device performance. Here, a simple approach to study the full 3D morphology of phase‐separated blends, taking advantage of the possibility to selectively dissolve the different components is introduced. This method is applied in combination with AFM to investigate a blend of a semiconducting and ferroelectric polymer typically used as active layer in organic ferroelectric resistive switches. It is found that the blend consists of a ferroelectric matrix with three types of embedded semiconductor domains and a thin wetting layer at the bottom electrode. Statistical analysis of the obtained images excludes the presence of a fourth type of domains. The criteria for the applicability of the presented technique are discussed. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 1231–1237     

Nano-tribological study on a super-hydrophobic film formed on rough aluminium substrates

A novel super-hydrophobic stearic acid (STA) film with a water contact angle of 166^o was prepared by chemical adsorption on aluminum wafer coated with polyethyleneimine (PEI) film. The micro-tribological behavior of the super-hydrophobic STA monolayer was compared with that of the polished and PEI-coated Al surfaces. The effect of relative humidity on the adhesion and friction was investigated as well. It was found that the STA monolayer showed decreased friction, while the adhesive force was greatly decreased by increasing the surface roughness of the Al wafer to reduce the contact area between the atomic force microscope (AFM) tip and the sample surface to be tested. Thus the friction and adhesion of the Al wafer was effectively decreased by generating the STA monolayer, which indicated that it could be feasible and rational to prepare a surface with good adhesion resistance and lubricity by properly controlling the surface morphology and the chemical composition. Both the adhesion and friction decreased as the relative humidity was lowered from 65% to 10%, though the decrease extent became insignificant for the STA monolayer. The project supported by the National Natural Science Foundation of China (50375151, 50323007, 10225209) and the Chinese Academy of Sciences (KJCX-SW-L2)     

Fracture toughening of epoxy matrices with blends of resins of different molecular weights and other modifiers

The microstructure and fracture behavior of epoxy mixtures containing two monomers of different molecular weights were studied. The variation of the fracture toughness by the addition of other modifiers was also investigated. Several amounts of high‐molecular‐weight diglycidyl ether of bisphenol A (DGEBA) oligomer were added to a nearly pure DGEBA monomer. The mixtures were cured with an aromatic amine, showing phase separation after curing. The curing behavior of the epoxy mixtures was investigated with thermal measurements. A significant enhancement of the fracture toughness was accompanied by slight increases in both the rigidity and strength of the mixtures that corresponded to the content of the high‐molecular‐weight epoxy resin. Dynamic mechanical and atomic force microscopy measurements indicated that the generated two‐phase morphology was a function of the content of the epoxy resin added. The influence of the addition of an oligomer or a thermoplastic on the morphologies and mechanical properties of both epoxy‐containing mixtures was also investigated. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 3920–3933, 2004     

Control of self‐organized low‐dimensional morphology in poly(styrene‐b‐4vinylpyridine)/polystyrene blend thin films

The surface morphologies of poly(styrene‐b‐4vinylpyridine) (PS‐b‐P4VP) diblock copolymer and homopolystyrene (hPS) binary blend thin films were investigated by atomic force microscopy as a function of total volume fraction of PS (?_PS) in the mixture. It was found that when hPS was added into symmetric PS‐b‐P4VP diblock copolymers, the surface morphology of this diblock copolymer was changed to a certain degree. With ?_PS increasing at first, hPS was solubilized into the corresponding domains of block copolymer and formed cylinders. Moreover, the more solubilized the hPS, the more cylinders exist. However, when the limit was reached, excessive hPS tended to separate from the domains independently instead of solubilizing into the corresponding domains any longer, that is, a macrophase separation occurred. A model describing transitions of these morphologies with an increase in ?_PS is proposed. The effect of composition on the phase morphology of blend films when graphite is used as a substrate is also investigated. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 3496–3504, 2004     

Surface and interfacial properties of PVDF/acrylic copolymer blends before and after UV exposure

Morphological and chemical properties of both the surface and interface of poly(vinylidene fluoride)/poly(methyl methacrylate)-co-poly(ethyl acrylate) (PVDF/PMMA-co-PEA) blend films have been investigated before and after the samples were exposed to ultraviolet (UV) irradiation using a xenon arc lamp at 50 °C and 9% relative humidity (RH) for 7 months. Surface and interfacial morphologies were studied by atomic force microscopy (AFM). Chemical composition information was obtained by confocal Raman microscopy, attenuated total reflection-FTIR spectroscopy (ATR-FTIR), X-ray photoelectron spectroscopy (XPS), and contact angle measurements. Results show an enrichment of the PVDF material at the air surface, while the acrylic copolymer enriches the interface. Blends having greater than 50% mass fraction of PVDF show little change in the surface morphology after UV exposure for 7 months. However, for a lower PVDF content, blends exhibit significant degradation of PMMA-co-PEA copolymer and a much rougher surface after UV exposure. Microstructural changes in the PVDF spherulites are also observed after UV degradation. It is found that the surface and interfacial morphologies are correlated with the chemical properties.     

Development of a “Built-in” Scanning Near Field Microscope Head for an Atomic Force Microscope System and Stress Mapping of an Al2O3/ZrO2 Eutectic Composite

We constructed a scanning near-field optical microscope (SNOM) on a commercially available atomic force microscopy (AFM) apparatus (SPM-9500J2; Shimadzu Corp.) to measure the stress distribution in ceramic composite materials. Features of our SNOM system are: (1) a compact SNOM head substituted for the original AFM head; (2) a wide scanning range (125 × 125 μm²) inherited from the original scanner; (3) use of conventional shear-force regulation; (4) an optical system for the illumination-collection (I-C) mode; (5) excitation by a 488 nm line of an Ar-ion laser, and (6) light detection by photon counting or a polychromator equipped with an electronically cooled charge coupled device (CCD). This SNOM system was used to measure the surface structure and stress distribution of an Al₂O₃/ZrO₂ eutectic composite. We simultaneously measured topographic images and fluorescence spectra of an Al₂O₃/ZrO₂ eutectic composite. We estimated its peak intensity, peak position, and peak width from the fluorescence spectrum during scanning, which respectively correspond to the abundance of Al₂O₃, stress in the grain, and the anisotropy of that stress. Mapping images showed that the stress and its anisotropy were weaker in the center of the Al₂O₃ grain than its boundary between Al₂O₃ and ZrO₂. That observation suggests that Al₂O₃ underwent intense anisotropic stress induced by volume expansion in the phase transition of ZrO₂ from the cubic phase to the monoclinic phase during preparation.     

Annealing behavior of gel‐spun polyethylene fibers at temperatures lower than needed for significant shrinkage

The annealing at 373 K of ultrastrong, gel‐spun polyethylene (PE) has been studied. At this temperature, the fibers show no significant shrinkage. Still, a significant decrease in the mechanical properties is observed. The fibers have been analyzed with differential scanning calorimetry (DSC), temperature‐modulated differential scanning calorimetry (TMDSC), atomic force microscopy (AFM), and small‐angle X‐ray scattering (SAXS). During the annealing, the glass transition of the intermediate phase is exceeded, as shown by DSC. When split for structure analysis by AFM, the annealed fibers undergo plastic deformation around the base fibrils instead of brittle fracture. The quasi‐isothermal TMDSC experiments are compared to the minor structural changes seen with SAXS and AFM. The loss of performance of the PE fibers at 373 K is suggested to be caused by the oriented intermediate phase, and not by major changes in the structure or morphology. The overall metastable, semicrystalline structure is shown by TMDSC to posses local regions that can melt reversibly. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 403–417, 2003     

Radiation‐induced migration of additives in PVC‐based biomedical disposable devices. Part 1. Surface morphology by AFM and SEM/XEDS

Two different types of plasticized poly(vinyl chloride) (PVC) used for biomedical disposable devices—extruded and injection moulded—were studied in the non‐sterilized condition and after 25 and 50 kGy of beta irradiation. The polymer surfaces were analysed by scanning electron microscopy (SEM) equipped with an x‐ray energy‐dispersive spectroscopy (XEDS) and by atomic force microscopy (AFM). The inner surface of two parts of a venous line showed a different morphology according to their original formulation (for extrusion or injection moulding process) and reacted differently on sterilization with beta irradiation. Moulded parts were affected only slightly by the radiation step, whereas the variations were bigger for the extruded parts. In order to gain the best performances for the medical devices studied, the utmost care must be taken in the sterilization step, which should be optimized as well as the other steps of the manufacturing process. Copyright © 2003 John Wiley & Sons, Ltd.     

Nanoscale surface of carbon nanotube fibers for medical applications: Structure and chemistry revealed by TOF-SIMS analysis

Surface structure and related chemistry understanding is a vital element in the design of high biocompatible materials since adsorption and adhesion of biological components are involved. These features are even more important in the case of nanostructured materials such as carbon nanotubes (CNTs) fibers. In our preliminary work we synthesised CNTs based fibers for medical applications. This new hybrid system combines polyvinyl alcohol (PVA) with CNTs and polylactic-co-glycolic acid (PLGA), a biodegradable copolymer. The surface properties of this material are investigated in order to guarantee a biocompatible response. Time-of-flight secondary ion mass spectrometry (TOF-SIMS) was found to be an ideal tool for fiber characterisation owing to its capacity to provide chemical specificity combined with detection limits beyond the reach of techniques previously used. Complementary morphological information is provided by atomic force microscopy (AFM). The corroboration of both data enables us to define the chemistry and structure of this new formulation.     

STM/AFM studies of the evolution of morphology of electroplated Ni/W alloys

The surface morphology evolution of Ni/W alloys was studied, as a function of the alloy composition. Using the modified plating baths developed in our laboratory recently, electroplated Ni/W alloys with different W content, in the range of 7–67 atom percent (a/o), can be obtained. This was found to lead to different structures, ranging from polycrystalline fcc-Ni type structure to amorphous, followed by orthorhombic with increasing W content in the alloy. Powder XRD was studied to determine the crystal structures. Ex situ STM, AFM and SEM were used to study in detail the surface morphologies of the different alloys, and their evolution with increasing W content.

The important findings are that a mixture of two crystalline forms can give rise to an amorphous structure. Hillocks that are usually a characteristic of epitaxial growth can also exist in the amorphous alloys. Oriented scratches caused by stress can also be formed.

Up to 20 a/o of W is deposited in the alloys in crystalline form, with the fcc-Ni type structure. Between 20 and about 40 a/o an amorphous structure is observed, and above that an orthorhombic crystal structure is seen, which is characteristic of the NiW binary alloy. Careful choice of the composition of the plating bath allowed us to deposit an alloy containing 67 a/o W, which corresponds to the composition NiW₂.