(111)择优取向的Pb(Zr0.52Ti0.48)O3铁电薄膜的制备及研究

选用不同浓度的Pb(Zr_0.52Ti_0.48)O₃溶胶，用Sol-gel法在Pt/Ti/SiO₂/Si基片上沉积一层厚度不同的Pb(Zr_0.52Ti_0.48)O₃ (PZT52)过渡层，经400℃烘烤、550℃退火等程序后，再用Sol-gel法在PZT52过渡层上沉积Pb(Zr_0.52Ti_0.48)O _{关键词： PZT铁电薄膜 择优取向 过渡层 剩余极化强度}     

Modal interferometer based on tapering single-mode-multimode-single-mode fiber structure by hydrogen flame

A modal interferometer is experimentally demonstrated based on tapering a single-mode-multimode-singlemode (SMS) fiber structure heated by hydrogen flame.The interference fringe begins to form when tapering length is 19.8 mm,and becomes regular and clear when the tapering length is longer and the tapered waist diameter is smaller.Annealing process is undertaken to achieve a high extension ratio of approximately 17 dB with free spectral range of 1.5 nm when the tapering length is 33 mm and the tapered waist diameter is approximately 5μm.The temperature and axial strain dependences of the tapered SMS structure are characterized,and the measured temperature and strain coefficients are +7 pm/℃and -9.536 pm/με, respectively.     

Theoretical analysis on double Rayleigh backscattering noise in optical fibreRaman amplifiers and its suppression

In this paper, amplified double Rayleigh backscattering noise (DRB) in the optical fibre Raman amplifier is analysed. Expressions are presented for both forward pumping and backward pumping schemes. Calculation is performed to show the effective suppression of DRB noise by employing an optical isolator. The optimal position for the isolator is determined and is found to be insensitive to the power levels of the signals and pumps. The results show that a reduction of the DRB noise by almost 2 to 3 orders can be reached.     

高局域性的可调硅基混合表面等离子体光相位调制器

设计和分析了一种可调硅基混合表面等离子体相位调制器.表面等离子体的引入打破了衍射极限的限制,使光场局域在一个纳米尺寸范围.该调制器的实现采用了两种原理:硅材料的等离子体色散效应以及聚合物的电光效应.由于器件结构的电容和寄生电阻较小,RC响应时间为3.77 ps,调制带宽大约100 GHz.当外加2.5V的驱动电压时,该...     

快速可调谐电光聚合物波导光栅

提出并设计了快速可调谐电光聚合物波导光栅.该波导光栅通过极化聚合物的线性电光效应 可实现谐振波长的纳秒级快速调谐，调谐灵敏度为61pm/V.研究了该波导光栅的反射谱和透 射谱特性与光栅周期,周期数,折射率调制函数及其调制大小的关系.讨论了波导光栅的材料 选择,制备工艺,快速可调谐性和偏振相关性.该波导光栅不仅克服了光纤光栅调谐速度慢和不利于大规模集成的不足，而且具有调谐灵敏度高,制备工艺与半导体工艺兼容和偏振无关 等优点. 关键词： 光通信器件 光波导 电光效应 聚合物 波导光栅 光纤光栅     

Numerical analysis of Raman amplification and optical signal-to-noise ratio in a photonic crystal fiber

A numerical design on the triangular photonic crystal fiber (PCF) based backward multi-pump Raman amplifier is presented. It is demonstrated that high flat Raman gain can be reached based on PCF. Influences of different geometric parameters and germanium doping concentrations on the Raman net gain, amplified spontaneous emission (ASE) noise and double Rayleigh backscattering (DRBS) of the signal have been analyzed. For optimizing crystal fiber Raman amplifier (FRA), there is tradeoff between the geometric parameter and germanium doping concentration of triangular PCF. The results show that PCF is an appropriate candidate for high gain Raman amplifiers.     

Measurement of the magnetic index of magnetic field-dependent refractive fluids in bulk

An optical alignment-free and highly accurate method is employed to measure the magnetic field-dependent refractive index of magnetic fluid （MF） in bulk. The measured refractive index decreases significantly with the increasing magnetic strength and then tends to saturate in the high intensity range. By applying a tunable magnetic field ranging between 0 and 1661 Oe, the maximum shift of the refractive index of MF in bulk is found to be 0.0231.     

单模光纤中弯曲损耗的测试与分析

对单模光纤中弯曲损耗随弯曲半径(1～8 mm)和波长(1530～1565 nm)变化的实验进行了测试,结果显示弯曲损耗随弯曲半径和波长呈现振荡.理论分析表明由于光纤纤芯中的基模和在包层以及涂覆层中传播的Whispering-gallery模式之间的耦合,引起了弯曲损耗的振荡,理论分析结果和实验结果基本一致.     

二阶非线性光学聚合物材料的最新研究进展

随着激光技术与光纤通信技术的蓬勃发展 ,迫切要求提高非线性光学极化聚合物的性能 ,以满足器件化的要求 ,这就需要从分子设计和极化方法等方面进行研究和优化。本文以聚合物主链结构为线索 ,以非线性光学性能为依据 ,介绍了二阶非线性光学聚合物的最新研究进展 ,并展望了该类聚合物在光通信领域的应用前景     

Highly efficient fiber-to-chip evanescent coupling based on subwavelength-diameter optical fibers

A novel, compact, and highly efficient fiber-to-chip evanescent coupling structure is proposed based on a subwavelength-diameter fiber. The coupling structure is characterized by a large misalignment tolerance and easy fabrication. The dependence of coupling efficiency on various parameters is calculated and analyzed. The simulation results show that a coupling efficiency as high as 95% can be obtained within a coupling length of <4 μm.