Effect of Hydrolysis Conditions on the Direct Formation of Nanoparticles of Ceria–Zirconia Solid Solutions from Acidic Aqueous Solutions

The effect of the cation concentration, hydrolysis temperature, and composition in the CeO₂–ZrO₂ system on the direct precipitation of ceria–zirconia solid solutions and the structure of the precipitates from acidic aqueous solutions of (NH₄)₂Ce(NO₃)₆ and ZrOCl₂ by hydrolysis under hydrothermal conditions were investigated. Nanometer-sized (8–10 nm) ceria–zirconia solid solution particles in a composition range of 0 to 60 mol% ZrO₂ were directly precipitated from the solutions with total metal cation concentration less than 0.2 mol/dm³ by simultaneous thermal hydrolysis at 150–240°C. The crystalline phase of the precipitates gradually changed from cubic and/or tetragonal to monoclinic with increasing the cation concentration of the solution from 0.2 to 0.8 mol/dm³ at the starting composition of 50 mol% ZrO₂ under hydrolysis condition of 150°C for 48 h, which was attributed to decrease in the supply of hydrolyzed Ce component caused by decrease in the hydrolysis ratio of (NH₄)₂Ce(NO₃)₆. Ceria–zirconia solid solutions containing large amount of ZrO₂ maintained high specific surface area and small-sized crystallite after heat-treatment at 900–1000°C for 1 h.     

Preparation of Sr2CeO4:Eu3+,Dy3+ white luminescence phosphor particles and thin films by using an emulsion liquid membrane system

Sr(2)CeO(4) and Sr(2)CeO(4):Eu(3+),Dy(3+) phosphor particles and thin films were prepared by using an emulsion liquid membrane (ELM, water-in-oil-in-water (W/O/W) emulsion) system, containing VA-10 (2-methyl-2-ethylheptanoic acid) as extractant (cation carrier). A two-step extraction enabled efficient extraction for Sr(3+) and rare earth ions, and the resulting precursor metal oxalate particles produced in the internal water phase of the ELM system were about 60 nm in diameter. Calcination of the oxalate particles in air gave submicrometer-sized Sr(2)CeO(4) and Sr(2)CeO(4):Eu(3+),Dy(3+) particles, which showed blue and white luminescence, respectively, by UV excitation. Blue and white luminescence phosphor thin films were also prepared by soaking alumina substrates into the W/O emulsion containing precursor oxalate particles, followed by calcination in air.     

Electron spin resonance study of polymerization of butadiene with tris(acetylacetonato)titanium and triethylaluminum

ESR spectra of homogeneous catalyst derived from tris(acetylacetonato)titanium(III) and triethylaluminum were observed at several temperatures from ?78°C, to +25°C, at molar ratios of aluminum to titanium of 1–108. At ?78°C, this catalyst yields a violet complex which shows an ESR signal with a g value of 1.959 and is associated with the first intermediate. At ?40°C to ?30°C, this signal decreases, and two signals with g values of 1.947 and 1.960 are observed. The latter two signals diminish at ?5°C to +10°C, while two kinds of new signals with g values of 1.965 and 1.969 appear overlapping each other. The structures of the species corresponding to these five signals are discussed on the basis of the ESR spectra, the intensity change, and the unpaired spin distribution. A new signal with a g value of 1.978 is found in the presence of butadiene at 25°C at Al/Ti > 8 and is assigned to a growing end of polybutadiene with this catalyst. The polymer yield increases remarkedly at Al/Ti molar ratios greater than 10. The microstructure of the resulting polymer consists almost completely of 1,2 units. The structure of the growing end is proposed to be a titanium (III) species containing two 1-substituted allyl groups, by comparison with the structure ascribed to the growing end of polybutadiene with n-butyl titanate-triethylaluminum catalyst.     

Electron spin resonance study on polymerization of alkyl acrylates with n-butyl titanate(IV)–triethylaluminum catalyst

n-Butyl titanate(IV)–triethylaluminum catalyst at Al/Ti molar ratios greater than 6 polymerizes methyl and n-butyl acrylates at ?78°C. The polymerization system which includes methyl acrylate at ?78°C, gives two ESR signals with g factors of 1.958 and 1.961 that overlap each other. The absorption intensity of the latter signal is approximately proportional to the polymer chain concentration calculated from polymer yield and the molecular weight. The polymerization system at Al/Ti ratios smaller than 3 has no catalytic activity on the polymerization and shows only the ESR signal with the g factor of 1.958. On the basis of these facts the ESR signal with the g factor of 1.961 is attributed to the active growing end of poly(methyl acrylate) with this catalyst. The character of this active growing end is discussed.     

Polyiodide composition in poly(vinyl acetate)-iodine-iodide complex

Polyiodide formed by complexation of poly(vinyl acetate) (PVAc) with iodine in the presence of iodide has been investigated by chemical analysis and resonance Raman spectrophotometry. When PVAc films were immersed in iodide-iodine aqueous solutions which had different ratios of iodide to iodine concentration [I^?]/[I₂], the complex films exhibited tremendous variations of swelling degree, despite the relatively small change in the amount of bound iodine. From a quantitative chemical analysis, the composition of polyiodide bound to PVAc was found to be 1.01 ± 0.035 in the molar ratio of iodide to iodine irrespective of the composition of the iodide-iodine aqueous solution ([I^?]/[I₂] = 2–500). The polyiodide formed in PVAc-iodine-iodide complex was therefore inferred to be (I₃^?)_n. Resonance Raman spectra obtained on PVAc-iodine-iodide complexes were also identical to those of the benzamide-iodine complex, in which the polyiodide consists of (I₃^?)_n, consistent with the result from chemical analysis.