Microwave‐assisted polycondensation of 4‐octylaniline with dibromoarylene

The Pd‐catalyzed polycondensation of 4‐octylaniline with various dibromoarylenes was carried out under microwave heating. Microwave heating led to a decrease in the reaction time and an increase in the molecular weight of the polymers as compared to conventional heating. Microwave heating also allowed the catalyst loading to be reduced to 1 mol %, yielding polymerization results that were comparable to those under conventional heating and 5 mol % catalyst. Investigations regarding field‐effect transistors and organic photovoltaic cells using the obtained poly(arylamine) with azobenzene units revealed that increasing the molecular weight of the polymer led to improved device performance, including hole mobility and power conversion efficiency. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 536–542     

A Hydroperoxide-Mediated Decarboxylation of α-Ketoacids Enables the Chemoselective Acylation of Amines

Strategies for the formation of amide bonds, that is, one of the most basic and important transformations in organic synthesis, have so far focused predominantly on dehydration reactions. Herein, we report and demonstrate the practical utility of a novel decarboxylative amidation of α-ketoacids by using inexpensive tert-butyl hydroperoxide (TBHP), which is characterized by high yields, a broad substrate scope, mild reaction conditions, and a unique chemoselectivity. These features enable the synthesis of peptides from amino acid derived α-ketoacids under preservation of the stereochemical information.     

Silicon-Based Integrated Optic Pressure Sensor Using Intermodal Interference between TM-Like and TE-Like Modes

In this paper, a silicon-based integrated optic pressure sensor using an intermodal interference between the fundamental TM-like and TE-like modes is described. The sensor consists of a micromachined rectangular diaphragm and a straight polystyrene optical waveguide passing over the diaphragm. Its sensitivity is theoretically known to be strongly dependent on the position of the waveguide over the diaphragm. To experimentally investigate such dependence, we fabricated a sensor with a 1.2 mm ×10 mm ×20 μm diaphragm, over which waveguides were placed at 50 μm intervals. The measured phase sensitivity was 98 mrad/kPa for the waveguide nearest to the diaphragm edge. The measurement was also carried out for the other waveguides. As theoretically expected, the largest sensitivity was obtained for the waveguide nearest to the edge.     

Light Diffraction of Aligned Polymer Fibers Periodically Dispersed by Phase Separation of Liquid Crystal and Polymer

We have confirmed light diffraction of aligned polymer fibers obtained by a phase separation of an anisotropic-phase solution of liquid crystal and polymer. He—Ne laser light passing through the polymer fibers was scattered in the axis vertical to the fibers, and had two peaks of light intensity symmetrical to the center of the transmitting laser spot. The two peaks were found to be caused by light diffraction due to the periodic polymer-fiber dispersion because the peaks corresponded to values calculated by intervals between the fibers. The periodical fiber networks are considered to be formed by anisotropic spinodal decomposition. This effect can be used to measure the dispersion order of the polymer fibers. © 2004 The Optical Society of Japan     

Changes in the near-edge X-ray absorption fine structure spectra of long-chain diacetylene derivatives through photopolymerization in Langmuir–Blodgett films

Photopolymerization of cadmium 10,12-pentacosadiynoate (CdDA) in Langmuir–Blodgett (LB) films, with the molecular packing well arranged by moderate preannealing, was investigated with near-edge X-ray absorption fine structure (NEXAFS) spectroscopy. Greenish films of polydiacetylene with an absorption wavelength of 705 nm were obtained through the photopolymerization of preannealed monomer LB films, and this resulted in an extended π-conjugate system based on the well-ordered monomer in a two-dimensional arrangement. The electronic structures of the polydiacetylenes were found to be correlated to the variation of the molecular arrangements in the films from the changes in the NEXAFS spectra through photopolymerization in the LB films. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 2329–2336, 2004     

Distributions of major-to-ultratrace elements among the particulate and dissolved fractions in natural water as studied by ICP-AES and ICP-MS after sequential fractionation.

In order to elucidate the distributions of the elements among the particulate and dissolved fractions in pond water, major-to-ultratrace elements in different sizes of particles as well as in the filtrate passed through the 0.05 microm filter were determined by inductively coupled plasma atomic emission spectrometry (ICP-AES) and inductively coupled plasma mass spectrometry (ICP-MS). The different sizes of particle samples (ca. 100-300 microg each) were collected on the membrane filters with pore sizes of 10, 3.0, 1.2, 0.4, 0.2 and 0.05 microm, respectively, by sequential fractionation. As a result, about 40 elements in different sizes of particles could be determined by ICP-AES and ICP-MS, after acid digestion using HNO3/HF/HClO4. Then, the fractional distribution factors of major-to-ultratrace elements among the particulate and dissolved fractions were estimated from the analytical results. The total contents of Al, Fe, Ti, REEs (rare earth elements), Bi, Pb and Ag in the particulate fractions (larger than 0.05 microm) were more than 80-90%, while those of Ca, Sr, Cs, W, Ba, Mn and Co in the dissolved fraction, which corresponded to the filtrate passed through the 0.05 microm membrane filter, were more than 80%. It was further found that the fractional distributions of Cu and Zn in the dissolved fraction were ca. 50%. In addition, the enrichment factors (EFs) of the elements in the particulate fractions with particle sizes of 3.0-10 microm and 0.05-0.2 microm were estimated to elucidate their geochemical characteristics in natural water.     

Facilitated sulfate transfer across the nitrobenzene-water interface as mediated by hydrogen-bonding ionophores.

Facilitated SO4(2-) transfers by hydrogen bond-forming ionophores are investigated across the nitrobenzene (NB)-water interface by using polarography with a dropping electrolyte electrode. Bis-thiourea 1, alpha,alpha'-bis(N'-p-nitrophenylthioureylene)-m-xylene, is found to significantly facilitate the transfer of the highly hydrophilic SO4(2-) whereas its counterpart, N-(p-nitrophenyl)-N'-propylthiourea (ionophore 2), cannot. In contrast to the predominant formation of a 1:1 complex with SO4(2-) in the bulk NB phase, the SO4(2-) transfer assisted by 1 is indeed based on the formation of a 1:2 complex between SO4(2-) and ionophore, even under the condition of [SO4(2-)]aq > [1]org. Such an exclusive formation of the 1:2 (SO4(2-) to ionophore) complex at the NB-water interface is not observed with structurally similar bis-thiourea 3, alpha,alpha'-bis(N'-phenylthioureylene)-m-xylene, where p-nitrophenyl moietes of bis-thiourea 1 are simply replaced by phenyl groups. The facilitated transfer of SO4(2-) with bis-thiourea 1 is further compared to that of HPO4(2-) and H2PO4- across the NB-water interface, which was previously shown to be assisted by 1 through the formation of the 1:1 and 2:1 (anion to ionophore) complexes, respectively. On the basis of these examinations, unique binding behaviors of hydrogen bond-forming ionophores at the NB-water interface are discussed, with a view towards development of ionophore-based anion-selective chemical sensors.     

Curved Ferroelectric Liquid Crystal Matrix Displays Driven by Field-Sequential-Color and Active-Matrix Techniques

This paper describes a curved field-sequential-color matrix display using fast-response ferroelectric liquid crystal. Black matrix and transparent electrode patterns were formed on a thin plastic substrate by a transfer method from a glass substrate. While a composite film of liquid crystal and micro-polymers of walls and fibers was formed between the flexible substrates by printing, laminating and curing processes of a solution of monomers and liquid crystal, the mechanical stability was enhanced by use of multi-functional monomers to form large display panels. The image pixels of the matrix panel were driven by an active matrix scheme using an external switch transistor array at a frequency of 180 Hz for intermittent three-primary-color backlight illumination. The flexible A4-paper-sized color display with 24 × 16 pixels and 60 Hz field frequency was demonstrated by illuminating it with sequential three-primary-color lights from light-emitting diodes of the backlight. Our display system is useful in various information displays because of its freedom of setting and location.     

Optical Glucose Monitoring Based on Femtosecond Two-Color Pulse Interferometry

We demonstrate the potential of femtosecond two-color pulse interferometry for in vitro optical glucose monitoring, by dispersion of the group refractive index in a glucose solution sample with respect to a red-color light and a blue-color light. By comparison with femtosecond one-color pulse interferometry, the basic performance of the present system with regard to sensitivity, quantitativeness, and tolerance to surrounding disturbances, is evaluated. The resulting accuracy and precision of glucose determination are 77 and 118mg/dl for 10-mm-sample-thickness, respectively. This near-common-path configuration of the two-color pulse light provides good stability to fluctuations of sample temperature, which is important in clinical applications. Considering the performance of femtosecond two-color pulse interferometry as an optical glucose sensor, a suitable measurement site for in vivo optical glucose monitoring is discussed.