LAXS investigation of finger phantoms

Osteoporosis is a bone condition that is caused mainly by the degradation of trabecular and cortical bone resulting in the decrease of bone strength and eventually leads to bone fracture. A low angle X-ray scattering (LAXS) system that uses mainly the coherent scattering process for the characterisation of materials was constructed to study such bone conditions. Several finger phantoms were fabricated to simulate bone of varying densities. The LAXS method was able to identify the changes in bone density quite well by comparing energy dispersive X-ray diffraction patterns as well as the angular patterns. Quantitative information can be extracted from such patterns that relate to bone loss. Signature patterns at low exposure times were produced in order to reduce the dose received with reasonable identification power but at slightly higher statistical errors compared with long exposure patterns. Use of other parameters to increase the sensitivity was attempted.     

Radiation pasteurised oil palm empty fruit bunch fermented with Pleurotus sajor-caju as feed supplement to ruminants

In solid state fermentation, Pleurotus sajor-caju has been found to be able to degrade at least 30% oil palm empty Fruit Bunch (EFB) fibre leaving 70 % useful materials. Conditions under which fermentation carried out were investigated. It was found that, in the temperature range between 25– 28 °C, relative ph between 6–8, moisture between 60–70 % and medium composition of CaCO₃: rice bran 2 %: 5 % were the optimum conditions. The results showed in fermented products that, there were substantial reduction in cellulosic component such as Crude Fiber (CF, 18 %); Acid Detergent Fibre (ADF, 45 %), Neutral Detergent Fibre (NDF, 61 %) and Acid Detergent Lignin (ADL, 14 %). However, Crude Protein (CP, 10%) increased resulted from single cell protein enrichment of mycelial microbial mass. The mass reductions of substrate in fermentation process corresponds to the CO₂ released during fermentation. Hence, attributable to the decreased in content of CF, ADF, NDF, and ADL. The digestibility study has also been carried out to determine the useful level of this product to ruminant. Aflatoxin content was detected low in both the initial substrates and products. Based on nutritional value and low content of aflatoxin, the product is useful as a source of roughage to ruminant.     

Flow injection-spectrophotometric determination of cresol compounds in water by reaction withp-aminophenol

A spectrophotometric method has been developed for the simultaneous determination ofo-cresol andm-cresol in water by reaction withp-aminophenol (PAP). Three different methodologies have been assayed; (i) batch analysis, after reaction in an alkaline medium in the presence of dissolved molecular oxygen as oxidizing agent, (ii) a stopped-flow procedure, carried out in the presence of KIO₄ and (iii) a flow injection method based on the same approach. The batch procedure requires 22 min for the full development of colour witho-cresol and 12 min form-cresol. In the stopped-flow mode, using KIO₄ and a reaction time of 12 min, better sensitivity can be obtained for both compounds and limits of detection of 10 g 1^–1 foro-cresol and 30 g 1^–1 form-cresol were found. The flow injection method has a lower sensitivity but permits more than 80 injections per hour. Based on the different maximum absorbance wavelengths obtained for the reaction products of PAP witho-cresol (614 nm) andm-cresol (632 nm), both compounds can be simultaneously determined in water samples and recoveries of 90 to 115% were found in spiked water samples of different types.     

Spectrophotometric determination of phenol and resorcinol by reaction with p-aminophenol

Based on the reaction with p-aminophenol, a series of procedures have been developed for the spectrophotometric determination of phenol and resorcinol. Three basic approaches have been studied: (i) a batch procedure, using the dissolved oxygen as oxidant, (ii) a stopped-flow procedure by use of KIO(4) as oxidant and (iii) a flow injection (FI) procedure developed in the presence of KIO(4). Phenol can be accurately determined at 626 nm, in the stopped-flow mode, after a reaction time of 45 min in 0.005M NaOH, 0.004M KIO(4) and 500 mug/ml of PAP. The development of a manifold, which incorporates a sample parking, is a convenient approach which makes it possible to measure, in the stopped-flow mode, four solutions in one hour. The limit of detection of this method corresponds to 64 ng/ml of phenol Resorcinol can be determined by FI at 540 nm in 0.006M NaOH, 0.0002M KIO(4) and 50 mug/ml PAP with a limit of detection of 6.6 ng/ml and a sample throughput of 300 injections per hour. A combination between the FI procedure for the determination of resorcinol and the stopped-flow procedure for phenol determination provides accurate results in the analysis of spiked samples containing both phenol and resorcinol.     

Starch cellulose acetate co-acrylate (SCAA) polymer as a drug carrier

The present study aims to create a controlled-release system through the preparation and characterization of starch cellulose acetate co-acrylate (SCAA) polymer for application as a carrier for cancer drugs. SCA was prepared from maize starch and different ratios of cellulose acetate. The obtained product SCA was reacted with acrylic acid monomer to give cellulose acetate co-acrylate. The best ratio of starch to cellulose acetate was found to be 90:10, giving a stable product with acrylic acid. The cancer drug 8-(2-methoxyphenyl)-3,4-dioxo-6-thioxo-3,4,6,7-tetrahydro-2h-pyrimido[6,1-c]-[1,2,4]triazine-9-carbonitrile was dissolved in dimethylformamide then added gradually at the end of the previous reaction under stirring for 15 min. The prepared polymers with and without the drug were characterized by Fourier-transform infrared spectroscopy. Cuboids discs of the prepared polymer/drug were subjected to drug release in aqueous media at different pH values. The release was measured spectrophotometrically. It was found that the release rate depends on the pH of the aqueous medium as well as on the concentration of the drug loaded onto the polymer carrier. Above pH 12, the polymer containing the drug degraded completely within 1 h after being subjected to alkaline media. Sustained release of drug extended to about 20 days. The amount released depended on the pH of the media in the following order: basic media > acidic media > neutral. According to Higuch’s equation, the diffusion coefficient was found to be 4.2 × 10^?8 and 5.5 × 10^?8 cm s^?1 for the two evaluated concentrations (1.5 and 2 %) of active organic compound (drug).     

Effect of chitosan derivatives as rubber antioxidants for increasing durability

A series of chitosan derivatives, namely polydiethylamino-ethylmethacrylate-chitosan-graft-copolymer (chitosan-g-DEAEMA), polycarboxy-chitosan-graft copolymer (chitosan-g-COOH), polyvinyl alcohol chitosan-graft-copolymer (chitosan-g-VOH), and carboxymethyl-chitosan (CM-chitosan), were synthesized and investigated as antioxidants for natural rubber (NR) and acrylonitrile butadiene rubber (NBR) mixes and vulcanizates to increase their durability. The rheometric characteristics of the rubber mixes were determined using an oscillating disc rheometer. The physico-mechanical properties of the rubber vulcanized were measured before and after exposure to thermal oxidative aging. It was found that the CM-chitosan had an accelerating effect on the curing process of NR and NBR. Also, the investigated polymers enhanced the properties of rubbers (NR and NBR) especially after ageing up to 7 days compared with commercial antioxidants, such as phenyl ß-naphthylamine (PßN) and N-isopropel-Nphenyl-p-phenylene diamine (IPPD) which are used in the rubber industry. After ageing, the retained values of tensile strength, modulus at 100 % strain, and elongation at break were improved. The optimum concentration of the investigated compounds used to give good properties was found to be 1–2 parts per 100 of rubber (phr). In addition, these prepared polymers showed a decrease in the equilibrium swelling of rubber in toluene which is the proper solvent and consequently increases the crosslink density for rubbers.     

Edge detection by spherical separation

We describe an optimization-based method for tackling the classic image processing problem known as edge detection and we formulate it in the form of a classification one. The novelty of the approach is in the use of spherical separation as a classification tool in the image processing framework. Spherical separation consists in separating by means of a sphere two given discrete point-sets in a finite dimensional Euclidean space; in our context the two sets are the edge points and the non-edge points, respectively, in the digital representation of a given image. Assuming that the center of the sphere is fixed, the problem reduces to the minimization of a convex and nonsmooth function of just one variable, which can be effectively solved by means of an “ad hoc” bisection method. The results of our experiments on some edge detection benchmark images are provided.     

Steps towards a practical synthesis of macrocyclic bisbenzylisoquinolines

There are more than 400‐reported bisbenzylisoquinoline alkaloids, many with interesting biological activity, but the reported syntheses are long and low yielding. As a result, there have been no systematic attempts at exploitation of the potential therapeutic applications. The concept of a sulfur ‘stitch’, restricting the conformational freedom of intermediates in the synthesis, will potentially allow analogues of the natural products to be prepared using relatively efficient routes. The synthesis of intermediate sulfur heterocycles is reported, based on 2,8‐dimethylphenoxathiin, leading via 2,8‐bis(bromomethyl)phenoxathiin‐10,10‐dioxide to a synthesis of 3,4,8,9‐tetrahydro‐13‐oxa‐6‐thia‐2,10‐diazapentacene, a key potential intermediate on the route to a variety of macrocyclic bisbenzylisoquinolines.