水化硅酸钙纳米压痕分子动力学模拟方法优化

针对水化硅酸钙纳米压痕模型忽视了压头与基底之间相互作用的问题，由尺寸差异引起的金刚石压头难以计算的问题，以及Wittmann模型无法得到实际接触面积的问题，提出了新的模型与计算方法．结合分子动力学方法，采用金刚石压头-Wittmann模型基底的组合方式构建无定形态水化硅酸钙纳米压痕试验模型．在建模阶段，考虑到压头模型与基底模型粒子间尺寸差异，提出了等比例替换模型，通过公式推导并就不同尺寸模拟结果验证了等比例替换模型的可行性．在计算阶段，提出了局部前处理的弛豫方法进行模拟．确定最大荷载位置处的接触面积为546 nm2，进而求出水化硅酸钙模型硬度H为0.84 GPa、折合模量Er为30.52 GPa．并通过纳米压痕试验，验证了模拟结果的准确性，证明了模型的科学性，对今后水化硅酸钙(C-S-H)纳米层面的模拟具有重要借鉴意义．     

Comparative analysis of the main active components and hypoglycemic effects after the compatibility of Scutellariae Radix and Coptidis Rhizoma

In this study, a rapid and highly sensitive ultra high performance liquid chromatography with triple quadrupole mass spectrometry method with the mobile phase of acetonitrile and 0.1% aqueous formic acid was established and successfully applied to comparatively analyze main active components after their compatibility. Besides, the effects of Scutellariae Radix, Coptidis Rhizoma and combined extracts on type 2 diabetic rats induced by high‐fat diet along with low dose of streptozocin were investigated. Under the optimized chromatographic conditions, good separation of seven target components was achieved within 12 min. All calibration curves exhibited good linearity (R² ≥ 0.999). The relative standard deviation of precision, repeatability and stability varied from 0.69 to 2.23, 0.98 to 2.56, and 0.92 to 2.57%, respectively. The recovery ranged from 91.11 to 105.35%. The contents of seven active components were notably reduced after compatibility; however, the hypoglycemic effect of combined extracts was stronger than single drug by decreasing the activities of fructose‐1,6‐bisphosphatase, glucose 6‐phosphatase, phosphoenolpyruvate carboxykinase and increasing the activities of glucokinase, phosphofructokinase, pyruvate kinase. Accordingly, the established analytical method was accurate and sensitive enough for quantitative evaluation of seven investigated compounds. Moreover, the combined extract had definite effects on type 2 diabetes through multiple components against multiple targets.     

Analysis of time series in the cumulative residual entropy plane based on oscillation roughness exponent

Nonlinear Dynamics - In this work, we propose the cumulative residual entropy (CRE) plane and CRE curve based on the weighted-multiscale cumulative residual Rényi/Tsallis permutation entropy...     

The High Energy X-ray telescope (HE) onboard the Insight-HXMT astronomy satellite

The Insight-Hard X-ray Modulation Telescope(Insight-HXMT) is a broadband X-ray and γ-ray(1-3000 ke V) astronomy satellite. One of its three main telescopes is the High Energy X-ray telescope(HE). The main detector plane of HE comprises 18 Na I(Tl)/Cs I(Na) phoswich detectors, where Na I(Tl) is used as the primary detector to measure ~ 20-250 ke V photons incident from the field of view(FOV) defined by collimators, and Cs I(Na) is used as the active shielding detector to Na I(Tl) by pulse shape discrimination. Additionally, Cs I(Na) is used as an omnidirectional γ-ray monitor. The HE collimators have a diverse FOV,i.e. 1.1°×5.7°(15 units), 5.7°×5.7°(2 units), and blocked(1 unit). Therefore, the combined FOV of HE is approximately5.7°×5.7°. Each HE detector has a diameter of 190 mm resulting in a total geometrical area of approximately 5100 cm2, and the energy resolution is ~15% at 60 ke V. For each recorded X-ray event by HE, the timing accuracy is less than 10 μs and the deadtime is less than 10 μs. HE is used for observing spectra and temporal variability of X-ray sources in the 20-250 ke V band either by pointing observations for known sources or scanning observations to unveil new sources. Additionally, HE is used for monitoring the γ-ray burst in 0.2-3 Me V band. This paper not only presents the design and performance of HE instruments but also reports results of the on-ground calibration experiments.     

Surface modification of polyolefin separators for lithium ion batteries to reduce thermal shrinkage without thickness increase

Surface chemical modification of polyolefin separators for lithium ion batteries is attempted to reduce the thermal shrinkage, which is important for the battery energy density. In this study, we grafted organic/inorganic hybrid crosslinked networks on the separators, simply by grafting polymerization and condensation reaction. The considerable silicon-oxygen crosslinked heat-resistance networks are responsible for the reduced thermal shrinkage. The strong chemical bonds between networks and separators promise enough mechanical support even at high temperature. The shrinkage at 150 C for 30 min in the mechanical direction was 38.6% and 4.6% for the pristine and present graft-modified separators, respectively. Meanwhile, the grafting organic-inorganic hybrid crosslink networks mainly occupied part of void in the internal pores of the separators, so the thicknesses of the graft-modified separators were similar with the pristine one. The half cells prepared with the modified separators exhibited almost identical electrochemical properties to those with the commercial separators, thus proving that, in order to enhance the thermal stability of lithium ion battery, this kind of grafting-modified separators may be a better alternative to conventional silica nanoparticle layers-coated polyolefin separators.