排序方式: 共有18条查询结果,搜索用时 15 毫秒
1.
2.
3.
平面研磨加工中工件转速的理论分析 总被引:1,自引:0,他引:1
平面研磨加工中工件转速决定了磨具与工件间的相对运动速度分布,并进而影响磨具和工件的面形精度。在考虑了磨具上金刚石丸片的实际排列以及接触区压强的实际分布的前提下,运用力学和运动学的方法,模拟分析了在固着磨料平面研磨加工中镜盘所受的摩擦力矩。在此基础上,根据稳定加工时力矩平衡原理得出了包含转速的数学公式,并重点探讨了工件半径和偏心矩对工件转速的影响。结果表明,工件转速并不总是等于磨具转速,而是随着偏心矩的增大而逐渐增高,随着工件半径的变化发生起伏波动。 相似文献
4.
一种新型TEA CO_2激光器的实验研究 总被引:4,自引:0,他引:4
设计了一种新型结构的激光器———双通道放电激励折叠腔TEA CO2激光器。该激光器通过提高脉冲能量输出水平来增加激光输出谱线数目和激光差分吸收雷达可探测的气体种类。它在增大激光器放电时间长度的同时保证了较小的激光器体积,更好地满足了激光差分吸收雷达光源体积小,重量轻,输出能量高的要求。得到激光器输出能量与气体工作气压的关系曲线,获得了激光器内工作气压与输出脉宽关系曲线,发现脉冲宽度大约在50~70ns之间变化,研究了气体压强对激光器输出脉冲峰值功率的影响。 相似文献
5.
A reliable target-triggering plasma shutter was applied to second harmonic generation (SHG) of AgGaSe2 crystal with a TEA CO2 laser. Under normal air pressure, argon charged plasma shutter was triggered by focusing beam companying with a pair of adjustable metal targets. Conversion efficiency was enhanced by 3.3 times and the maximal efficiency 9.3%, with 1.4-mJ second harmonic energy was obtained. Finally, crystal damage was discussed together with previous work. 相似文献
6.
The optical system for detecting wake profiles based on laser backscattering by bubbles at 180°is reported, in which the monostatic optical geometry is adopted and the power density estimation is used to process bubble scattering signal.The profiles of wakes produced by a two-blade propeller with a diameter of 46 mm at 6000 and 8000 rpm are measured using this system.It is shown that the wake region can be identified,the wake with different shapes can be distinguished,and the fine structure within wakes can be detected.Also,the repeatability of the results is tested experimentally.Results show the feasibility of this system in wake profile detection. 相似文献
7.
A passively Q-switched side-pumped laser with folded resonator is specially constructed for single- longitudinal-mode smooth pulse output. Nd:YAG is chosen as the laser active medium and Cr^4+:YAG as the saturable absorber medium. Additionally, the method of frequency selection by grating with 1200 line/mm and Fabry-Perot (F-P) etalon is used in the twisted-mode cavity. The single-frequency smooth pulses are produced with 10-Hz repetition rate, 20-ns pulse width, and 1.064-μm wavelength. The proba- bility of single-frequency laser output measured is over 99% by using the methods of Fourier analysis and F-P etalon multiple-beam interferometry at the threshold voltage. The measured near-field and far-field angles of divergence are 1.442 and 1.315 mrad, respectively. The values of M^2 are 1.32 and 1.31 separately with the knife-edge method. Single pulse at 1.064 tim with the energy of 8.8 mJ is achieved in TEM00 mode. 相似文献
8.
Investigation results on linear and non-linear optical properties, damage threshold and potential efficiencies of biaxial negative LiInS2 crystal are represented. It shows that the crystal has phase-matching and group-velocity matching in wide spectral range for second harmonic, sum- and difference-frequency generation of visible, near and middle IR lasers. The possibilities of designing middle IR optical parametric oscillator (OPO) pumped by Nd:YAG and dye lasers and specially possibility of frequency conversion with 3 um range femtosecond erbium lasers are given. 相似文献
9.
10.