质子注入能量对垂直腔面发射激光器的阈值和功率的影响

文章研究了如何兼顾质子注入型垂直腔面发射激光器的功率和阈值性能.从模拟和实验两方面分析了质子注入能量与器件功率和阈值特性的关系.发现注入能量过高时,损伤有源区,降低了功率性能.而能量过低则会减弱对注入电流的限制,增加阈值.计算和实验结果表明,对于文中的器件结构,315 keV的注入能量是合适的.在10μm的注入孔径下获得器件的阈值为4.3 mA,功率为1.7 mW.     

跨声速轴流压气机动叶弯和掠效应的应用

对一单级跨声速轴流压气机的动叶分别进行了前掠和正弯研究,然后针对前掠和正弯叶片各自所存在的问题分别作了改进.对掠动叶中部的叶型做了二维改型以降低中部的激波强度和分离损失;对弯动叶不同截面叶型的安装角进行调整以消除正弯对动叶出口气流角的影响.最终应用前掠和正弯动叶的压气机的效率得到明显的提高.在对正弯和前掠动叶研究的基础之上,对动叶进行了前掠和正弯相联合的设计以综合利用弯和掠的有利作用.同时对弯掠动叶中部截面的叶型进行了二维改型以降低中部分离损失,并且对不同叶高截面的安装角进行调整以消除对出口气流角的影响.最终应用弯掠动叶的压气机效率和失速裕度都得到显著提高.     

Vertical cavity surface emitting laser transverse mode and polarization control by elliptical hole photonic crystal

The polarization of traditional photonic crystal(PC) vertical cavity surface emitting laser(VCSEL) is uncontrollable,resulting in the bit error increasing easily.Elliptical hole photonic crystal can control the transverse mode and polarization of VCSEL efficiently.We analyze the far field divergence angle,and birefringence of elliptical hole PC VCSEL.When the ratio of minor axis to major axis b/a = 0.7,the PC VCSEL can obtain single mode and polarization.According to the simulation results,we fabricate the device successfully.The output power is 1.7 mW,the far field divergence angle is less than 10°,and the side mode suppression ratio is over 30 dB.The output power in the Y direction is 20 times that in the X direction.     

Vertical cavity surface emitting laser transverse mode and polarization control by elliptical holes photonic crystal

The polarization of traditional photonic crystal (PC) vertical cavity surface emitting laser (VCSEL) is uncontrollable, resulting in the bit error increasing easily. Elliptical hole photonic crystal can control the transverse mode and polarization of VCSEL efficiently. We analyze the far field divergence angle, and birefringence of elliptical hole PC VCSEL. When the ratio of minor axis to major axis b/a=0.7, the PC VCSEL can obtain single mode and polarization. According to the simulation results, we fabricate the device successfully. The output power is 1.7 mW, the far field divergence angle is less than 10°, and the side mode suppression ratio is over 30 dB. The output power in the Y direction is 20 times that in the X direction.     

氧化孔形状对光子晶体垂直腔面发射激光器模式的影响

用时域有限差分方法对氧化孔限制型外腔式光子晶体垂直腔面发射激光器 (VCSEL) 在小氧化孔下氧化孔形状对激光器模式特性的影响进行了模拟计算. 建立了三维光子晶体面发射激光器光场计算模型, 分析了氧化孔形状变化对器件远场特性与频率特性的影响. 研究发现, 氧化孔形状可影响光子晶体VCSEL的模式特性, 尤其是频谱特性. 从模场分布的角度可解释为菱形氧化孔的对称性与高阶模的不一致. 但随着光子晶体刻蚀深度的增加和氧化孔的增大, 这种影响逐渐减小, 分析解释了其原因. 研究结果为提高光子晶体面发射激光器的性能提供了参考.     

弯掠动叶对跨声压气机非定常气动负荷的影响

对一单级跨声压气机设计工况采用弯掠动叶前、后的非定常流场进行了数值模拟,深入分析了动叶弯掠对压气机叶片非定常气动负荷的影响.结果表明t动叶弯掠后,动、静叶的气动力和气动力矩时均值由于叶片负荷大小及分布的不同变化而产生不同程度的改变;由于动叶对下游静叶的尾迹和二次流干扰远强于动叶所受到的下游静叶的势流干扰,静叶的气动负荷发生较大波动;弯掠动叶减轻了端壁损失并且减弱了顶部泄漏涡强度和根部角区分离,从而减弱了对下游静叶的非定常干扰,这使得静叶各气动参数的波动幅值显著降低.