Surface of room temperature ionic liquid [bmim][PF6] studied by polarization- and experimental configuration-dependent sum frequency generation vibrational spectroscopy

Understanding and control of the surface properties such as molecular orientations are of great importance in numerous applications of ionic liquids. However, there remain discrepancies among the previous experimental and theoretical studies on the surface orientation and structures of room temperature ionic liquids(RTIL) systems. In this article, the orientation of 1-butyl-3-methylimidazolium([bmin]) cation at the air/liquid interface of a characteristic RTIL, 1-butyl-3-methylimidazolium hexafluorophosphate([bmim][PF6]), was investigated by the sum frequency generation vibrational spectroscopy(SFG-VS). Detailed polarization and experimental configuration analyses of the SFG-VS spectra showed the possibility of a small spectral splitting in the CH3 symmetric stretching region, which can be further attributed to the probable existence of multiple orientations for the interfacial [bmim] cations. In addition, the(N)–CH3 vibrations were absent, ruling out the prediction by several recent molecular dynamics simulations which state that portions of the [bmim] cations orient with a standing-up(N)–CH3 group at the ionic liquid surface. Hence, new realistic theoretical models have to be developed to reflect the complex nature of the ionic liquid surface.     

各向异性本构关系在板料成形数值模拟中的应用

对几种能表达面内各向异性的屈服准则Hill、Barlat-Lian、Barlat进行了比较。以弹性变形服从各向同性广义虎克定律的情况下，给出了基于张量算法推导的弹塑性本构关系的一般表达式，并由此导出了相应屈服准则的弹塑性本构关系的显式表达。借助ABAQUS软件本构模块用户子程序接口，分别实现了这些屈服准则在ABAQUS的嵌入。以模拟方形盒的拉延过程为例，分析了不同的屈服准则在板料成形过程数值模拟中的应用。模拟结果表明，基于弹塑性本构关系一般表达所列出的相应屈服准则的显式表达式是正确的；在采用壳元来模拟板料成形时，采用Barlat准则的模拟结果和采用Barlat-Lian准则的结果差别不大。     

La_2O_3和WSi_2增强MoSi_2基复合材料的摩擦磨损性能研究

选用MRH-5A型环-块摩擦磨损试验机测定了3种载荷和2种转速条件下La2O3和WSi2增强MoSi2基复合材料在滑动干摩擦时的摩擦磨损性能,采用扫描电子显微镜分析了复合材料磨损表面形貌.结果表明:La2O3和WSi2增强MoSi2基复合材料的抗磨性能优于MoSi2及WSi2/MoSi2材料;当载荷与速度乘积(pv)值小于183.04N·m/s时,La2O3和WSi2增强MoSi2基复合材料的磨损质量损失仅为相同条件下MoSi2的1/4～1/6和WSi2/MoSi2的1/2;这是由于La2O3和WSi2复合增强相存在硬化和韧化协同作用所致;随着pv值增加,La2O3和WSi2增强MoSi2基复合材料依次呈现犁削、粘着磨损和疲劳磨损特征.     

中心裂纹圆盘应力强度因子的测试误差分析

本文在中心裂纹圆盘应力强度因子解析解的基础上,利用一阶微分法则,给出了与裂纹相对长度和加载角相关的应力强度因子(K 和K )的4个误差传递函数。这4个误差传递函数关于裂纹相对长度和加载角均是非线性的,它们既是误差分析的基础,又是合理确定裂纹相对长度和加载角的基础。分析结果表明,加载角的误差Δθ除了对纯 型K 的误差几乎没有影响,对纯 型K 影响较小外,对复合型K 、K 的误差均有较大影响。最后,本文建议裂纹相对长度的取值范围为0.4～0.6;还建议在复合型断裂试验时,必须依据对K 、K 的总体精度要求来严格控制加载角的精度。     

EFFECTS OF FINELY DISPERSED METALLIC PALLADIUM ON MICROSTRUCTURE AND PROPERTIES OF NANOCOMPOSITES PRODUCED BY SOL-GEL TECHNIQUE

Nanosized palladium particles were incorporated into mesoporous silica matrix to obtain nanocomposites using the sol-gel technique. Effects of the finely dispersed metallic palladium on the microstructure and properties of the nanocomposites were investigated. By means of X-ray diffraction and optical absorption, it was found that palladium particles were 5-9 nm in diameter and their uniform dispersion in the mesoporous silica depended on both the content of the palladium and the structural features of the silica matrix. The results showed that the mixing method of preparation led to wider size distribution of the nanosized particles as compared to the immersion method, but dispersed degree was reduced. Although the incorporation of nanosized palladium particles could not substantially induce significant structural changes of the matrix, the apparent red-shifted optical absorptions for the nanocomposites were observed as compared to the parent monolithic silica, particularly with increase in palladium loading and calcination temperature.     

非保守圆薄板的轴对称振动和稳定性

建立了受切向均布随从力作用的圆薄板在面内周边可移、不可移两种情况下的轴对称控制方程，用打靶法直接导出求解变系数常微分方程特征值问题数值解的计算式．通过数值计算，给出了周边可移、不可移的简支、固支圆板自振频率和临界载荷的特征曲线以及相应的临界发散载荷，并分析了泊松比对圆板自振频率和临界载荷的影响．     

反射焦散线实验中斜入射光对应力强度因子测试精度的影响

本文用空间解析几何方法,推导了在一般非平行斜入射光条件下,裂纹体表面所形成的反射焦散线和初始曲线的方程.分析了倾斜入射光造成的焦散线畸变,给出了这种畸变造成的裂端应力强度因子测量误差的解析表达式.     

SYNTHESIS AND CHARACTERIZATION OF SURFACE-HYPERBRANCHED MAGNETITE NANOPARTICLE FOR BOVINE SERUM ALBUMIN IMMOBILIZATION

A hyperbranched polyamidoamine polymer was synthesized on the surface of magnetite nanoparticles to enhance bovine serum albumin (BSA) immobilization efficiency. The amount of immobilized bovine serum albumin (BSA) on the surface-hyperbranched magnetite nanoparticle was up to 2.5 times as much as that of magnetite nanoparticle modified with only amino silane.     

相变材料接触熔化的研究

对有关相变材料接触熔化的研究成果进行了全面的综述, 内容包括:封闭空间的接 触熔化、围绕热源的接触熔化、滑动接触熔化、滚动接触熔化、冰的压力熔化、接 触熔化的量级分析与修正、由液体边界层内的热扩散引起的熔化、不连续接触点上 熔化与润滑、固体内部传热的影响、玻璃的软化与接触熔化.     

镍钛记忆合金自补偿磨粒磨损性能研究

研究了高临界温度镍钛记忆合金一维自补偿磨粒磨损特性.结果表明,在一定温度下,镍钛记忆合金在摩擦过程中具有形状恢复能力,从而产生一维磨损自补偿作用.超弹状态镍钛记忆合金具有热弹性马氏体相变、高阻尼、应力感生马氏体、超弹性、高应变硬化指数和时效弥散析出强化等特性,这使得硬度较低的镍钛合金的耐磨性能远优于硬度较高的淬火45#钢.利用超弹状态镍钛记忆合金的磨损自补偿作用可望开发出新型抗磨形状记忆合金产品.