Topical application of zein-silk sericin nanoparticles loaded with curcumin for improved therapy of dermatitis

Atopic dermatitis is characterized by leukocyte migration into the skin dermis and typically driven by excessive chemokine production at the site of inflammation. Conventional topical formulations such as gels, creams, and ointments are insufficient for this treatment because of low penetration of drug molecules into the targeted skin tissues. Herein, using a simple, green, sustainable strategy, we have developed novel primary zein nanoparticles embedded in curcumin (Cur) and coated with silk sericin (ZHSCs) for the topical delivery of Cur to penetrate into the dermis and exercise anti-dermatitis effects on the lesion with minimal side-effects. Transdermal delivery experiments and porcine skin fluorescence imaging indicated that ZHSCs facilitate the penetration of Cur across the epidermis layer of skin to reach deep-seated sites. Notably, ZHSCs = 1:0.25 (zein-to-silk sericin mass ratios of 1:0.25) markedly elevated the skin permeability and cumulative turnover of Cur transferred, which were provided a greater than a 3.8-fold increase relative to free Cur. The special nanoparticles of ZHS = 1:0.25 possessed the deepest localization depth and experience a transition of the particle structure and core-shell separation after penetrating into the dermis of skin. In a cell model of dermatitis induced by tumor necrosis factor α/interferon γ co-stimulation, compared with free Cur, Cur-loaded ZHS nanoparticles down-regulated the generation of inflammatory cytokines and chemokines in keratinocytes through suppression of the nuclear translocation of NF-κBp65 and hence exerted an anti-dermatitis effect. This strategy may provide new avenues and direction for the demanding issues of valid topical delivery systems.     

Experimental and Numerical Simulation Research on Boundary Layer Transition Front over a Swept Wing at M = 6

Fluid Dynamics - To predict the boundary layer transition on swept wings, experimental and numerical researches were conducted to obtained the accurate boundary layer transition front and to...     

Preparation and Properties of Sr3B2O6:Dy3+, Eu3+ White Phosphors Using the High-Temperature Solid-State Method

Journal of Applied Spectroscopy - Sr3B2O6:Dy3+, Eu3+ single-matrix white-light-emitting materials are prepared using the high-temperature solid-state method. The microstructure, emission spectrum,...     

Restricted testing conditions for the multilinear maximal operator

Restricted testing conditions were considered recently. For the maximal operator, Hytönen, Li and Sawyer [8] first obtained parental testing condition. Later, they [9] showed that it suffices to restrict testing to doubling cubes. Chen and Lacey [3] gave a similar restricted testing condition. In our paper, we discuss a version of the latter in the multilinear setting.

     

Multi-scale Fractured Coal Gas–Solid Coupling Model and Its Applications in Engineering Projects

With coal mining entering the geological environment of “high stress, rich gas, strong adsorption and low permeability,” the difficulty of joint coal and gas extraction clearly augments, the risk of solid–gas coupling dynamic disasters greatly increases, and the underlying mechanisms become more complex. In this paper, based on the characteristics of coal’s multi-scale structure and spatiotemporal variation, the multi-scale fractured coal gas–solid coupling model (MSFM) was built. In this model, the interaction between coal matrix and its fractures and the mechanical characteristics of gas-bearing coal were considered, as well as their coupling relationship. By MATLAB software, the stress–damage–seepage numerical computation programs were developed, which were applied into Comsol Multiphysics to simulate gas flow caused by coal mining. The simulation results showed the spatial variability of coal elastic modulus and cross-flow behaviors of coal seam gas, which were superior to the results of traditional gas–solid coupling model. And the numerical results obtained from MSFM were closer to the measured results in field, while the computation results of traditional model were slightly higher than the measured results. Furthermore, the MSFM in a large scale was verified by field engineering project.     

Rate sensitivity and deformation mechanism of semi-crystalline polymers during instrumented indentation

Instrumented indentation tests using both constant loading rate (CLR) and continuous stiffness measurement (CSM) operation modes were performed to investigate the deformation mechanism and their sensitivity to the deformation rate in semi-crystalline polymers through the quantitative analysis of load-depth loading and unloading curves. The strain rate was constant during the CSM tests, while the strain rate decreased with the increasing of loading time in CLR tests. The mechanical response mechanism of the semi-crystalline polymers to these tests was very complicated because of the combined effects of strain-hardening in the crystal phase and strain-softening in the amorphous phase. Results show that the loading index m reflects the strain-hardening or strain-softening response during indentation. When m > 2, the mechanical response was due to the strain-hardening, and when m < 2, the response was due to strain-softening. A method based on the measured contact hardness was proposed to obtain the unloading stiffness, and the other mechanical parameters could then be determined according to the unloading stiffness.     

Synthesis and Structural Characterization of a Di-nuclear Uranyl Complex with Quinoline-6-carboxylate

Crystallography Reports - A di-nuclear uranyl complex with the formula of [(UO2)2(L)4(H2O)2]?4H2O (1) (HL = quinoline-6-carboxylic acid) was synthesized hydrothermally and characterized by...     

In situ confinement of iron-based active sites within high porosity carbon frameworks with enhanced activity for rechargeable Zn–air battery

Non-noble bifunctional electrocatalysts with robust activity and stability toward oxygen evolution reaction (OER) and oxygen reduction reaction (ORR) are greatly significant but challenging for Zn-air batteries. Here, in situ confinement of FeN_x active sites in high porosity carbon framework (FeN_x/CMCC) derived from chelate of carboxymethylcellulose (CMC) and iron ions were synthesized. Particularly, construction of FeN_x within porous carbon framework accelerates the electron transfer and the sufficient utilization of active centers, and then expedites the reaction kinetics of ORR and OER. As expected, the optimized FeN_x/CMCC exhibits superior ORR activity with a larger half-wave potential of 0.869 V. The rechargeable Zn-air battery delivers a higher power density of 99.6 mW/cm² and a special capacity of 781.9 mA h/g_Zn at 10 mA/cm², together with excellent durability of over 335 h. Remarkably, the as-assembled solid-state battery exhibits a higher open circuit voltage (OCV) of 1.5 V, a special capacity of 709.7 mA h/g_Zn, as well as prolonged cycling stability (90 h). Moreover, the flexible solid-state battery displays negligible loss of electrochemical performance under various bending angles, illustrating its potential application in flexible electronic devices.     

Simultaneous determination of 75 abuse drugs including amphetamines,benzodiazepines, cocaine,opioids, piperazines,zolpidem and metabolites in human hair samples using liquid chromatography–tandem mass spectrometry

A liquid chromatography–tandem mass spectrometric method for the simultaneous determination of 75 abuse drugs and metabolites, including 19 benzodiazepines, 19 amphetamines, two opiates, eight opioids, cocaine, lysergic acid diethylamide, zolpidem, three piperazines and 21 metabolites in human hair samples, was developed and validated. Ten‐milligram hair samples were decontaminated, pulverized using a ball mill, extracted with 1 mL of methanol spiked with 28 deuterated internal standards in an ultrasonic bath for 60 min at 50°C, and purified with Q‐sep dispersive solid‐phase extraction tubes. The purified extracts were evaporated to dryness and the residue was dissolved in 0.1 mL of 10% methanol. The 75 analytes were analyzed on an Acquity HSS T3 column using gradient elution of methanol and 0.1% formic acid and quantified in multiple reaction monitoring mode with positive electrospray ionization. Calibration curves were linear (r ≥ 0.9951) from the lower limit of quantitation (2–200 pg/mg depending on the drug) to 2000 pg/mg. The coefficients of variation and accuracy for intra‐ and inter‐assay analysis at three QC levels were 4.3–12.9% and 89.2–109.1%, respectively. The overall mean recovery ranged from 87.1 to 105.3%. This method was successfully applied to the analysis of 11 forensic hair samples obtained from drug abusers.