Tailored side‐chain architecture of benzil voltage stabilizers for enhanced dielectric strength of cross‐linked polyethylene

The synthesis and physico‐chemical properties of seven benzil‐type voltage stabilizers are reported. The benzil core is substituted with alkyl chains of different length that are linked to the benzil core via an ester, ether, or tertiary amine group. All additives can be melt‐processed with low‐density polyethylene (LDPE). Fourier‐transform infrared spectroscopy confirms that benzil compounds are not affected by the LDPE cross‐linking reaction induced by dicumyl peroxide. Moreover, a combination of gel content measurements, thermal analysis, and small‐angle X‐ray scattering indicates that the presence of benzil voltage stabilizers does not significantly alter the microstructure of cross‐linked polyethylene (XLPE). Electrical tree inhibition experiments under high‐voltage alternating current conditions show that all investigated additives substantially enhance the dielectric strength of the insulating material at a concentration of only 10 mmol kg^?1. The highest improvement in dielectric strength, of more than 70% with respect to reference XLPE, is obtained with voltage stabilizers, which carry short (methyl) side chains that are linked to the benzil core via an ester or tertiary amine group. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2014 , 52, 1047–1054     

CO2 gasification of char from spent mushroom substrate in TG-MS system

Journal of Thermal Analysis and Calorimetry - Gasification of the char obtained from the spent substrate after mushroom cultivation was carried out in a thermobalance connected to a mass...     

Simple gases to replace non-environmentally friendly polymer foaming agents. A thermodynamic investigation

Foaming constitutes one of the most important industrial activities in polymer engineering to produce efficient thermal insulating materials. In particular, rigid insulating boards are produced worldwide on a large scale using blowing agents which eventually are released in the environment where they adversely impact the natural friendly stratospheric ozone layer. Concomitantly, the chemicals used as blowing agents contribute to the creation of the unfriendly tropospheric ozone layer generating the disastrous green house effect around our planet. The traditional foaming intermediates currently named freons, like chlorofluorocarbons (CFCs) currently used as blowing agents as well as the hydrochlorofluorocarbons (HCFCs) often considered as alternative blowing agents, must be banned from industrial processes and new (friendly) foaming agents have to be suggested and evaluated in terms of both easy engineering and environmental neutrality. Undoubtedly thermodynamics plays a major role in assessing the effective capability of those chemicals. Some CFCs still accepted and other possible simple gases like carbon dioxide and nitrogen have been considered. The in-depth thermodynamic investigation has been made possible thanks to new experimental developments to determine gas solubility in polymers and associated swelling as well as the thermodynamic properties of (gas + polymer) systems, including the thermophysical properties of polymers under gas sorption. Pertinent data have been generated for such properties over extended T and p ranges.     

Design of polyglycidol-containing microspheres for biomedical applications

The paper presents a short review on the synthesis, characterisation and selected medical applications of poly(styrene/α-tert-butoxy-ω-vinylbenzyl-polyglycidol) (P(S/PGL)) microspheres. The soap-free emulsion-polymerisation of styrene and α-tert-butoxy-ω-vinylbenzyl-polyglycidol macromonomer (PGL) in water yielded core-shell microspheres with a low particle-diameter dispersity (ratio of the weight average particle diameter and the number average particle diameter). The interfacial fraction of PGL units, estimated by XPS, was in the range of 0–42 mole % depending on the concentration of the macromonomer in the polymerisation feed. The studies of adsorption of model proteins showed that the surface fraction of adsorbed protein was significantly reduced when the PGL interfacial fraction was higher than 40 mole %. The P(S/PGL) particles with covalently immobilised proteins were used for the preparation of photonic crystal assemblies suitable for applications in optical biosensors and the medical diagnostic test for the detection of Helicobacter pylori antibodies in the blood serum.     

Phase diagram and dielectric relaxation studies of n-octyl-isothiocyanato-biphenyl (8BT) in the crystalline E phase under high pressure

The pressure-temperature phase diagram of n-octyl-isothiocyanato-biphenyl (8BT) in the pressure range up to 250 MPa (2.5 kbar) and the temperature range 250-400 K was established with the aid of DTA. At 1 atm the substance exhibits exclusively CrE polymorphism. At pressures above 190 MPa, the clearing line splits showing an additional phase which is not yet identified. Dielectric relaxation measurements on the CrE phase of 8BT were performed in the pressure range 0.1-120 MPa and the temperature range 304-345 K. A Debye-type relaxation process was observed in the frequency range 100 Hz-1 MHz. The longitudinal relaxation time τ, characterizing the molecular reorientations around the short axis, was analysed with respect to the pressure and temperature, yielding the activation volume, Δ^# V = RT(? ln τ/?p)_T, and activation enthalpy, Δ^# H = R(? ln τ/? T^-1)_p, respectively. The results are compared with analogous data obtained recently for similar compounds having other liquid crystalline phases (N, SmA).     

On Suboptimal LCS-alignments for Independent Bernoulli Sequences with Asymmetric Distributions

Let X = X ₁ ... X _n and Y = Y ₁ ... Y _n be two binary sequences with length n. A common subsequence of X and Y is any subsequence of X that at the same time is a subsequence of Y; The common subsequence with maximal length is called the longest common subsequence (LCS) of X and Y. LCS is a common tool for measuring the closeness of X and Y. In this note, we consider the case when X and Y are both i.i.d. Bernoulli sequences with the parameters ϵ and 1 − ϵ, respectively. Hence, typically the sequences consist of large and short blocks of different colors. This gives an idea to the so-called block-by-block alignment, where the short blocks in one sequence are matched to the long blocks of the same color in another sequence. Such and alignment is not necessarily a LCS, but it is computationally easy to obtain and, therefore, of practical interest. We investigate the asymptotical properties of several block-by-block type of alignments. The paper ends with the simulation study, where the of block-by-block type of alignments are compared with the LCS.     

Efficient calculation of SAMPL4 hydration free energies using OMEGA,SZYBKI, QUACPAC,and Zap TK

Several submissions for the SAMPL4 hydration free energy set were calculated using OpenEye tools, including many that were among the top performing submissions. All of our best submissions used AM1BCC charges and Poisson–Boltzmann solvation. Three submissions used a single conformer for calculating the hydration free energy and all performed very well with mean unsigned errors ranging from 0.94 to 1.08 kcal/mol. These calculations were very fast, only requiring 0.5–2.0 s per molecule. We observed that our two single-conformer methodologies have different types of failure cases and that these differences could be exploited for determining when the methods are likely to have substantial errors.