Microwave‐assisted polycondensation of 4‐octylaniline with dibromoarylene

The Pd‐catalyzed polycondensation of 4‐octylaniline with various dibromoarylenes was carried out under microwave heating. Microwave heating led to a decrease in the reaction time and an increase in the molecular weight of the polymers as compared to conventional heating. Microwave heating also allowed the catalyst loading to be reduced to 1 mol %, yielding polymerization results that were comparable to those under conventional heating and 5 mol % catalyst. Investigations regarding field‐effect transistors and organic photovoltaic cells using the obtained poly(arylamine) with azobenzene units revealed that increasing the molecular weight of the polymer led to improved device performance, including hole mobility and power conversion efficiency. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 536–542     

Measurement of intense microwave field patterns using a neon glow indicator lamp

A novel method using small neon glow lamps with electrodes is developed for measuring intense microwave field patterns. When the lamp axis coincide with the electric field direction, the lamp discharge starts at the feeblest microwave electric field strength. Therefore, the lamp axis shows the field direction and the discharge starting indicates the field strength. The field strength for starting the microwave discharge is less than the strength for AC discharge, because of its low loss discharge mechanism. In the experiments using a microwave oven, it has been demonstrated again comparing with the simulated results that the method is able to use for measuring the intense electric field strength and direction.     

Non-Darcian effects on conjugate natural convection between horizontal concentric cylinders filled with a porous medium

An analysis is presented of steady conjugate free convection between two horizontal concentric cylinders filled with a fluid-saturated porous medium; the innermost cylinder surface is maintained at a high temperature and the outermost cylinder surface at a lower one. The velocity-pressure-gradient relation is taken to be nonlinear, with departure from the linear Darcy situation measured by a parameter F₀. The investigation is based on the numerical solution, by a finite-difference method, of the full momentum and energy equations. The streamline and isotherm patterns as well as the local and mean Nusselt numbers are plotted for several physical parameters to show some of the flow and heat transfer characteristics. It is found that all parameters play an important role in the flow and heat transfer characteristics. The model can be applied to a variety of engineering problems.     

Fluorescence spectra,fluorescence quantum yields and fluorescence lifetimes of polymers having trans-1,2-dicarbazolylyclobutane or carbazolyl group

Quantum yields, lifetimes and shapes of fluorescence from polymers containing the trans-1,2-dicarbazolylcyclobutane (DCZB) or carbazolyl structures were studied in N,N-dimethylformamide. No sandwich-type excimer formation was observed for DCZB polymers. The so-called second excimer observed in poly(9-vinylcarbazole) might also be produced in poly(9-ethyl-3-vinylcarbazole).     

Magnesium-butadiene addition compounds: Isolation,structural analysis and chemical reactivity

The magnesium-butadiene 1 : 1 (1), 1 : 2 (II) and 1 : 3 addition compounds obtained by the direct metalation of butadiene with metallic magnesium were isolated. These compounds have a polymeric structure. Structural analysis of these compounds by NMR and IR methods was carried out. The process for the formation of II via I and III via II was investigated. The results of protolysis and alkylation of the above magnesium compounds corresponded well to those of crotylmagnesium compounds.     

Preparation of Polymer Particles Coated with Hydroxyapatite

Polymer particles coated with hydroxyapatite were prepared by treating Pd0 immobilized polystyrene-co-acrylic acid particles in aqueous CaCl2 and NaH2PO2 solutions. Hydroxyapatite coating took place at neutral to alkaline pH conditions, and the homogeneous growth of the hydroxyapatite layer on the surface of polymer particles was observed at relatively low temperature (30-50 degrees C). The thickness of the hydroxyapatite layer increased with reaction time. Copyright 1999 Academic Press.     

Distribution of polymer deposition in plasma polymerization. III. Effect of discharge power

Distribution of polymer deposition in an inductively coupled rf discharge system is studied as a function of level of discharge power with acetylene and styrene as monomers. When a fixed flow rate is used, the discharge power has a relatively small effect on the pattern of distribution of polymer deposition as long as values of W/FM, where W is discharge wattage, F is flow rate, and M is molecular weight of monomer, are maintained above a critical level to maintain full glow in the reaction tube. It has been shown that plasma polymerization of two monomers which have different molecular weights can be compared in a fair manner by selecting conditions to yield similar value of W/FM.     

Plasma polymerization of tetrafluoroethylene. III. Reproducibility and effects of substrate and reactor materials

Plasma polylmerization occurs in plasmas surrounded by surfaces and polymer formation is one of the complicated interactions that take place between active species and molecules which constitute surfaces and gas phases. Effects of reactor wall, substrate materials, flow rate, and discharge power on polymer formation, and properties of polymer deposits were investigated by ESCA, IR (infrared) spectroscopy, and the measurement of system pressure. The effect of surface is important at the initial stage of plasma polymerization which can be easily detected by the system pressure change; however, integrated properties such as IR spectroscopy and the deposition rate show the effect in a less pronounced manner. ESCA, which reflects the properties of surface (approximately 20 A? in depth), showed the effect of surface in an even less sensitive manner. The amount and properties (including the effects of surfaces) are dependent on plasma polymerization parameter W/FM(W, wattage; F, volume flow rate; and M, molecualar weight of monomer) and the location of deposition within a reactor. IR and ESCA data clearly showed the dependence of polymer properties on W/FM; i.e., increase of W and decrease of M to be equivalent. When all these factors were kept under control, the reproducibility of plasma polymerization was found to be excellent.     

Vaporization and thermal decomposition of transition metal salts in flameless atomic absorption spectrometry with a carbon tube atomizer

Vaporization and thermal decomposition of Cr, Mn, Fe, Co, Ni and Cu salts were investigated by measuring the absorption spectra observed when aqueous solutions of these salts were heated in the carbon tube atomizer. Gaseous metal halides are vaporized in the atomizer at temperatures above 300–500° C. SO₂ and NO are produced by thermal decomposition of metal sulfates and nitrates, respectively. The vaporization of metal halides is also confirmed by the spectra for solutions of metals in hydrochloric acid and for mixtures of metal nitrates and ammonium halides.