一类非线性发展方程的精确解

利用hirota双线性法,得到(3+1)维孤子方程、(3+1)维KP-Boussinesq方程、(2+1)维修正Caudrey-Dodd-Gibbon-Kotera-S awada方程、Hirota-Satsuma浅水波方程的精确解,并做出一部分解的图形,进一步研究解的结构和性质.     

基于级联PPMgLN晶体的双倍/三倍频双波长激光器

本文演示了紧凑的绿色和近红外双色连续波激光光源,其发射波长分别为516 nm和775 nm。设计并制造了级联的周期性极化掺镁铌酸锂晶体,用于同时转换通信波长的二次谐波(SHG)和三次谐波(THG),可以在相同温度下获得绿色和近红外激光的输出。通过建立一个单程激光测量系统,在2 W泵浦功率下获得516 nm的0.15 mW绿光和775 nm的1.19 mW的光,晶体温度控制在30.8 ℃。实验结果将为单激光器泵浦的紧凑型双波长共线激光器提供重要的案例。     

发动机机油滤清器虑层强度分析及优化

针对机油滤清器工作工况下进出口压差、机油滤层强度及导流桩高度等问题, 通过试验测试与仿真相结合, 对滤清器初步设计进行了评估及优化, 以确保滤清器在工作工况下进出口压降及滤层强度能满足要求. 首先进行滤层性能试验, 得到滤层的惯性阻力系数和黏性阻力系数; 再通过滤层多孔介质CFD分析, 对滤清器进出口压降进行分析计算. 结果表明: 在-18℃、25℃和70℃的工况下, 进出口压降都小于10kPa, 满足相关要求. 针对滤层的最大主应力超过其抗拉强度的问题, 通过CAE仿真分析, 优化滤层与导流桩间隙, 将滤层最大主应力由110.1MPa降至36.99MPa, 小于其抗拉强度42.8MPa.     

基于耦合声场建模的膨胀腔消声器声学性能分析及试验

针对圆柱形膨胀腔消声器三维建模及声学性能分析问题, 提出一种基于切比雪夫变分原理的耦合声场建模方法, 建立三维圆柱形膨胀腔消声器理论模型并搭建试验台架, 传递损失试验结果验证了理论模型的准确性. 将膨胀腔消声器内部声场分解为多个子声场, 基于子声场间压力与质点振速连续性条件, 推导声场耦合变分公式, 构建子声场拉格朗日泛函. 将子声场声压函数展开为切比雪夫-傅里叶级数形式, 通过瑞利-里兹法求解膨胀腔消声器频率、声压响应及传递损失. 计算并对比分析扩张比、扩张腔长度、进出口管偏置对膨胀腔消声器消声性能的影响. 结果表明: 扩张比增大会有效提高消声器在低频段的消声性能, 进出口管的偏置对消声器消声性能影响很小.     

基于应变梯度理论的微尺度蜂窝等效模量计算方法

本文提出了一种新的能够计及尺度效应的微纳米蜂窝等效模量的计算方法。将一种单参数应变梯度理论引入到本构方程当中,并基于能量等效原理推导了蜂窝面内等效模量地计算公式。算例分析表明,本文方法能够有效地计及尺度效应对蜂窝等效模量的影响。尺度效应与胞壁厚度和长度的值都有关,当胞壁厚度较小时,尺度效应显著,本文方法预测的模量会明显高于传统方法;而当胞壁厚度较大时,尺度效应变得微弱乃至可以忽略不计。但如果胞壁的长度/厚度比很大,则面内等效模量会趋近于0,此时是否考虑尺度效应意义不大。     

Rational Design of a Near-infrared Fluorescent Material with High Solid-state Efficiency,Aggregation-induced Emission and Live Cell Imaging Property

Near-infrared(NIR) fluorescent materials with high photoluminescent quantum yields(PLQYs) have wide application prospects. Therefore, we design and synthesize a D-A type NIR organic molecule, TPATHCNE, in which triphenylamine and thiophene are utilized as the donors and fumaronitrile is applied as the acceptor. We systematically investigate its molecular structure and photophysical property. TPATHCNE shows high T_gof 110℃ and T_d of 385℃ and displays an aggregation-induced emission(AIE) property. A narrow optical bandgap of 1.65 eV is obtained. The non-doped film of TPATHCNE exhibits a high PLQY of 40.3% with an emission peak at 732 nm, which is among the best values of NIR emitters. When TPATHCNE is applied in organic light-emitting diode(OLED), the electroluminescent peak is located at 716 nm with a maximum external quantum efficiency of 0.83%. With the potential in cell imaging, the polystyrene maleic anhydride(PMSA) modified TPATHCNE nanoparticles(NPs) emit strong fluorescence when labeling HeLa cancer cells, suggesting that TPATHCNE can be used as a fluorescent carrier for specific staining or drug delivery for cellular imaging. TPATHCNE NPs fabricated by bovine serum protein(BSA) are cultivated with mononuclear yeast cells, and the intense intracellular red fluorescence indicates that it can be adopted as a specific stain for imaging.     

一种通过梯形PPMgLN波导倍频实现带宽可调谐光源的理论研究

本文设计了一种梯形的周期极化掺镁铌酸锂(PPMgLN)波导,并通过在传播方向上引入温度梯度来拓宽其倍频(SHG)过程的泵浦光源可接收带宽。通过有限差分的光束传输法,计算波导的有效折射率,并进行波导尺寸的设计。结果表明,通过改变梯形波导不同位置的温度,使其形成一个温度梯度,可拓宽泵浦光源的波长可接收带宽。本文所设计的PPMgLN波导最大泵浦光源可接收带宽为C波段,即1 530~1 565 nm,该波导可倍频C波段,得到输出波段带宽为765~782.5 nm,温度调谐范围为30~150 ℃。     

射频等离子制备石墨烯负载Co3O4催化剂及其析氧性能研究

氢能的引入能有效提升配电网的供电可靠性,而电解水制氢是实现低碳转型的关键技术,开发高效的电解水催化剂势在必行。过渡金属氧化物储量大、催化活性高,是具有广阔应用前景的析氧反应催化剂。本文通过射频等离子体处理制备石墨烯上负载Co₃O₄析氧催化剂,XRD、Raman和XPS测试结果显示,二维结构石墨烯的引入加速表面电子迁移,增大了反应面积。等离子体处理促进了纳米粒子在石墨烯上的负载,利用等离子体刻蚀作用在催化剂表面制造出大量碳结构缺陷和氧空位结构,改善了活性位点分布,有效调控Co₃O₄电子结构,提高析氧催化活性。电化学测试表明,本文中合成的Co₃O₄@rGO在电流密度为50 mA·cm^-2时的过电位为410 mV,动力学反应速率较快,表现出优于商业IrO₂的析氧催化活性。     

A microfluidics-dispensing-printing strategy for Janus photonic crystal microspheres towards smart patterned displays

From the implementation point of view, the printable magnetic Janus colloidal photonic crystals (CPCs) microspheres are highly desirable. Herein, we developed a dispensing-printing strategy for magnetic Janus CPCs display via a microfluidics-automatic printing system. Monodisperse core/shell colloidal particles and magnetic Fe₃O₄ nanoparticles precursor serve as inks. Based on the equilibrium of three-phase interfacial tensions, Janus structure is successfully formed, followed by UV irradiation and self-assembly of colloid particle to generate magnetic Janus CPCs microspheres. Notably, this method shows distinct superiority with highly uniform Janus CPCs structure, where the TMPTA/Fe₃O₄ hemisphere is in the bottom side while CPCs hemisphere is in the top side. Thus, by using Janus CPCs microspheres with two different structural colors as pixel points, a pattern with red flower and green leaf is achieved. Moreover, 1D linear Janus CPCs pattern encapsulated by hydrogel is also fabricated. Both the color and the shape can be changed under the traction of magnets, showing great potentials in flexible smart displays. We believe this work not only offers a new feasible pathway to construct magnetic Janus CPCs patterns by a dispensing-printable fashion, but also provides new opportunities for flexible and smart displays.     

Polymeric Carbon Nitride-based Single Atom Photocatalysts for CO2 Reduction to C1 Products

Photocatalytic CO₂ reduction to C₁ fuels is considered to be an important way for alleviating increasingly serious energy crisis and environmental pollution. Due to the environment-friendly, simple preparation, easy formation of highly-stable metal-nitrogen(M-N_x) coordination bonds, and suitable band structure, polymeric carbon nitride-based single-atom catalysts(C₃N₄-based SACs) are expected to become a potential for CO₂ reduction under visible-light irradiation. In this review, we summarize the recent advancement on C₃N₄-based SACs for photocatalytic CO₂ reduction to C₁ products, including the reaction mechanism for photocatalytic CO₂ reduction to C₁ products, the structure and synthesis methods of C₃N₄-based SACs and their applications toward photocatalytic CO₂ reduction reaction(CO₂RR) for C₁ production. The current challenges and future opportunities of C₃N₄-based SACs for photoreduction of CO₂ are also discussed.