Controlling thermomechanical behavior of semicrystalline hydrogenated polynorbornene through the cis- to trans-cyclopentylene ratio

Though polynorbornene synthesized by ring-opening metathesis polymerization has an intrinsically all-cis configuration of the cyclopentylene backbone rings, a fraction of these rings can be epimerized to the trans configuration during hydrogenation over suitable catalysts. By varying the method of hydrogenation, semicrystalline hydrogenated polynorbornenes (hPNs) with trans levels between 0 and 36% were obtained. With increasing trans content, the glass transition temperature, melting point, and enthalpy of melting decrease modestly. By contrast, the temperature at which the hPN crystal transitions into a rotationally disordered polymorph varies strongly with trans content, ranging from 126 °C (all-cis) to 71 °C at 27% trans; at trans contents of 34% and above, no rotationally-ordered phase is observed at any temperature. The room-temperature Young's modulus shows no dependence on trans content, while the yield stress drops by 20% at 1% trans content and slowly decreases further with additional epimerization. The temperature dependence of the Young's modulus differs for trans-containing versus all-cis polymers, while the temperature dependence of the yield stress is set by the polymorph type (rotationally ordered vs. disordered).     

Catalytic Behavior of Mono-N-Protected Amino-Acid Ligands in Ligand-Accelerated C−H Activation by Palladium(II)

Mono-N-protected amino acids (MPAAs) are increasingly common ligands in Pd-catalyzed C−H functionalization reactions. Previous studies have shown how these ligands accelerate catalytic turnover by facilitating the C−H activation step. Here, it is shown that MPAA ligands exhibit a second property commonly associated with ligand-accelerated catalysis: the ability to support catalytic turnover at substoichiometric ligand-to-metal ratios. This catalytic role of the MPAA ligand is characterized in stoichiometric C−H activation and catalytic C−H functionalization reactions. Palladacycle formation with substrates bearing carboxylate and pyridine directing groups exhibit a 50–100-fold increase in rate when only 0.05 equivalents of MPAA are present relative to Pd^II. These and other mechanistic data indicate that facile exchange between MPAAs and anionic ligands coordinated to Pd^II enables a single MPAA to support C−H activation at multiple Pd^II centers.     

Physicochemical properties and bio-interfacial interactions of surface modified PDLLA-PAMAM linear dendritic block copolymers

Here, we demonstrate the applicability of self-assembling linear-dendritic block copolymers (LDBCs) and their nanoaggregates possessing varied surfaces as therapeutic nanocarriers. These LDBCs are comprised of a hydrophobic, linear polyester chemically coupled to a hydrophilic dendron polyamidoamine (PAMAM)—the latter of which acts as the surface of the self-assembled nanoaggregate in aqueous media. To better understand how surface charge density affects the overall operability of these nanomaterials, we modified the nanoaggregate surface to yield cationic (NH₃⁺), neutral (OH), and anionic (COO⁻) surfaces. The effect of these modifications on the physicochemical properties (i.e., size, morphology, and surface charge density), colloidal stability, and cellular uptake mechanism of the polymeric nanocarrier were investigated. This comparative study demonstrates the viability of nanoaggregates formed from PDLLA-PAMAM LDBCs to serve as nanocarriers for applications in drug delivery.     

Experimental investigation into the nonlinear dynamics of a bistable laminate

Nonlinear Dynamics - An experimental study of the single-well and twin-well, also referred to as intra-well and inter-well, respectively, nonlinear dynamics of a bistable composite laminate is...     

Tuning the phase behavior of semicrystalline hydrogenated polynorbornene via epimerization

Hydrogenated polynorbornene (hPN) synthesized by ring‐opening metathesis polymerization (ROMP) exhibits a thermoreversible change in crystal polymorph at a temperature T _cc below its melting point, T _m. The polymorphic transition corresponds to a sharp increase in rotational disorder around the chain axis as the temperature is increased above T _cc. Saturation of ROMP polynorbornene (PN) to hPN can be achieved through both catalytic and noncatalytic approaches. Here, three different hydrogenation routes were employed on the same precursor polymer: catalytic routes over either supported Pd⁰ or a Ni/Al complex, and noncatalytic saturation with diimide. The different hydrogenation routes result in hPNs with varying degrees of epimerization of the cyclopentylene ring (from cis to trans); these epimerized units are included in the hPN crystals. The crystal structure of the rotationally ordered hPN polymorph, observed below T _cc, changes sharply at low levels of epimerization and then is weakly influenced by further increases in trans content. The stability of the rotationally ordered hPN polymorph decreases with increasing epimerization, as reflected in a reduction of T _cc from 134 °C to 92 °C at 22% epimerization. T _cc is less affected by epimerization than by the inclusion of a similar content of 5‐methylnorbornene units, reflecting the smaller size of the trans defect. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2019 , 57, 1188–1195     

Chemical immobilization of crosslinked polymeric ionic liquids on nitinol wires produces highly robust sorbent coatings for solid-phase microextraction

Super elastic nitinol (NiTi) wires were exploited as highly robust supports for three distinct crosslinked polymeric ionic liquid (PIL)-based coatings in solid-phase microextraction (SPME). The oxidation of NiTi wires in a boiling (30% w/w) H₂O₂ solution and subsequent derivatization in vinyltrimethoxysilane (VTMS) allowed for vinyl moieties to be appended to the surface of the support. UV-initiated on-fiber copolymerization of the vinyl-substituted NiTi support with monocationic ionic liquid (IL) monomers and dicationic IL crosslinkers produced a crosslinked PIL-based network that was covalently attached to the NiTi wire. This alteration alleviated receding of the coating from the support, which was observed for an analogous crosslinked PIL applied on unmodified NiTi wires. A series of demanding extraction conditions, including extreme pH, pre-exposure to pure organic solvents, and high temperatures, were applied to investigate the versatility and robustness of the fibers. Acceptable precision of the model analytes was obtained for all fibers under these conditions. Method validation by examining the relative recovery of a homologous group of phthalate esters (PAEs) was performed in drip-brewed coffee (maintained at 60 °C) by direct immersion SPME. Acceptable recoveries were obtained for most PAEs in the part-per-billion level, even in this exceedingly harsh and complex matrix.